rept-ftp-meas

4.387 rept-ftp-meas

Use this command to manually initiate generation and FTP transfer of a measurements report from the Measurements Platform MCPM or Integrated Measurements enabled E5-OAM to an FTP server.

Parameters

enttype (mandatory)

Entity type to report on in the measurements report.

Range:

aiq: Measurements for ANSI41 AIQ
atinpq: Measurements for ATINP
deir: Measurements for S13/S13' EIR
eir: Measurements for Equipment Identity Register
enum: Measurements for ENUM Mobile Number Portability and Tier One Address Resolution
gttapath: Measurements for GTT Actions Per-Path
gttset: Measurements per GTTSET
idpr: Measurements for IDPR
link: Measurements for signaling links
lnkset: Measurements for linksets
lnp: Measurements for local number portability
lsdestni: Measurements for linkset destination network identifiers
lsonismt: Measurements for ISUP message type screening
lsorigni: Measurements for linkset originating network identifiers
mapscrn: Measurements for GSM MAP message screening
np: Measurements for INP, INP CRP, G-Port, A-Port, MO-based GSM SMS NP, MO-based IS41 SMS NP, IGM, MT-Based GSM SMS NP, and MT-Based IS41 SMS NP
origni: Measurements for originating network identifiers greater than 5
origninc: Measurements for originating network identifiers (less than 5, small networks) for network clusters
sctpasoc: Measurements per association for the SCTP protocol (used to carry M3UA, M2PA, and SUA traffic)
sctpcard: Measurements per card for the SCTP protocol (used to carry M3UA, M2PA, and SUA traffic)
sfthrot: Measurements for SFTHROT GTT Action
sip: Measurements for SIP
stp: Measurements pertaining to the Signaling Transfer Point in general or summarized totals recorded on the STP
tt: Measurements for translation types
ua: Measurements per application server/association for the M3UA and SUA protocols
vflex: Measurements for V-Flex

type (mandatory)

Type of measurement report.

Range:

avl: Availability measurements
avld: Daily availability measurements
avldth: Day to hour availability measurements.
comp: Component measurements
gtwy: Internetwork gateway-related data from the STP for ANSI and ITU measurements. ANSI gateway measurements are pegged on a per-linkset, per-Network Indicator basis, whereas ITU measurements are pegged on a per-linkset basis.
mtcd: Daily maintenance measurements
mtcdth: Day-to-hour maintenance measurements
mtch: Hourly maintenance measurements
mtcs: Link/linkset maintenance status
nm: Network management, on-demand
rbase: Schedule-report type record base measurements
systot: STP system totals

day (optional)

Day of the week for the specified daily measurement report.

Range:

mon
tue
wed
thu
fri
sat
sun

Default:

If not specified, the previous single day is reported.

hh (optional)

Half-hour for the specified report. The end time for the collection interval. For example, hh=0300 generates a report for the interval 2:30-3:00.

Range:: 0000 - 2400
hhmm where hh=00 -24 (hour) and mm=00 or 30 (minute)

period (optional)

The relative period for the report.

Range:

active
last
specific

qh (optional)

Quarter-hour for the specified report. The end time for the collection interval. For example, qh=0315 generates a report for the interval 3:00-3:15.

Range:: 0000 - 2400
hhmm where hh = 00-24 (hour) and mm = 00, 15, 30 or 45

Example

rept-ftp-meas:type=systot:enttype=stp

rept-ftp-meas:type=systot:enttype=sip

rept-ftp-meas:type=mtch:enttype=deir

rept-ftp-meas:type=mtch:enttype=enum

rept-ftp-meas:type=mtcd:enttype=sfthrot

rept-ftp-meas:type=mtch:enttype=gttset

Dependencies

This command cannot be used to specify a report type if that report type is currently printing.

A primary MCPM card must be available when this command is entered.

The 15 Minute Measurements feature must be turned on and the 15 Minute Measurements collection option (chg-measopts:collect15min=on command) must be on before the qh parameter can be specified.

The LNP feature must be turned on before the mtchlnp=on, mtcdlnp=on, or enttype=lnp parameter can be specified.

The GSM Map Screening feature must be turned on before the mtcdmap=on and enttype=mapscrn parameters can be specified

The EIR feature must be turned on before the enttype=eir parameter can be specified,.

If a value of avl, avld, comp, gtwy, mtcd, or systot is specified for the type parameter, then the value specified for the hh parameter must indicate a half-hour boundary (the end of the requested half-hour for the report). If the type=mtch parameter is specified, then the value specified for the hh parameter must indicate an hourly boundary (half hours ending in 00, such as 0100, etc).

The qh parameter must specify a quarter-hourly boundary (the end of the requested quarter-hour for the report) for valid report types (avld(th), mtcd(th), mtch, nm, rbase, and mtcs) cannot be specified.

Hourly collection and report processing cannot be in progress when report type mtch is specified.

Day-to-hour collection and report processing cannot be in progress

When report type mtcd is specified
When report type mtcdth is specified

Daily collection and report processing cannot be in progress when report type mtcd is specified.

Half-hourly collection and report processing cannot be in progress when report type comp, systot, avl, or gtwy is specified.

Quarter-hourly collection and report processing cannot be in progress when report type comp, systot, avl, or gtwy is specified.

5-minute collection and report processing cannot be in progress when report type nm is specified.

The mtcdth report type is unavailable between midnight and 1:00 AM (0100).

The day parameter can be specified only for report type mtcd and entity types aiq, eir, lnp, np, vflex, mapscrn, atinpq, and gttapath.

The hh and qh parameters cannot be specified together in the command.

When the period=last parameter is specified, the hh, qh, and day parameter cannot be specified.

When the period=active parameter is specified, the hh, qh, and day parameters cannot be specified.

When the period=specific parameter is specified, the hh, qh, or day parameters must be specified.

Table 4-42 indicates valid parameter combinations for measurements reports; invalid combinations will generate an error message.

Table 4-42 rept-ftp-meas Valid Parameter Combinations

Param. Value	:type Values
	avl	avld	avldth	comp	gtwy	mtcd	mtcdth	mtch	mtcs	nm	systot	rbase
entity
aiq						X		X
atinpq						X		X
deir						X		X
eir						X		X
enum						X		X
gttapath						X		X
gttset						X		X
idpr											X
link	X	X	X	X		X	X		X	X		X
linkset				X	X	X	X		X	X		X
lnp						X		X
lsdestni					X
lsonismt					X
lsorigni					X
mapscrn						X		X
np						X		X
origni					X
origninc					X
sctpasoc				X		X	X
sctpcard				X		X	X
sfthrot						X					X
SIP						X					X
stp					X	X	X			X	X	X
tt											X
ua				X		X	X
:period
active									X			X
last	X	X	X	X	X	X	X	X		X	X
specific	X			X	X	X		X			X

An hourly boundary must be specified for report type mtch.

The oamhcmeas=on or platformenable=on parameter must be specified (see the chg-measopts command) before this command can be entered.

The V-Flex feature must be turned on before the enttype=vflex parameter can be specified.

The A-Port, G-Port, IS41 GSM Migration, Prepaid SMS Intercept Ph1, TIF ASD, TIF GRN, TIF Number Portability, or TIF Simple Number Substitution feature must be enabled, or the INP, MO SMS IS41-to-GSM Migration, MO-based GSM SMS NP, or MO-based IS41 SMS NP feature must be turned on before the mtchnp=on or mtcdnp=on parameter can be specified.

The ANSI41 AIQ feature must be enabled before the enttype=aiq parameter can be specified.

The Integrated Measurements or Measurements Platform feature must be turned on before this command can be entered.

The GTT Action - DUPLICATE, GTT Action - DISCARD, or GTT Action - FORWARD feature must be enabled before the enttype=gttapath parameter can be specified.

At least one SFTHROT GTT Action must be provisioned before the enttype=sfthrot parameter is specified.

SIPNP Feature must be enabled before the enttype=sip and type=mtcd/systot parameters can be specified.

Period/type parameter combinations:

If the period=specific parameter is specified, then a value of avl, mtcd, comp, systot, gtwy, or mtch must be specified for the type parameter.
If the type=mtcd and period=specific parameters are specified, then a value of lnp, mapscrn, np, eir, vflex, atinpq, aiq, or gttapath must be specified for the enttype parameter.
If the period=active parameter is specified, then a value of mtcs or rbase must be specified for the type parameter.
If the period=last parameter is specified, then a value of mtcs or rbase cannot be specified for the type parameter.

At least one ENUM card must be present before the enttype=enum parameter can be specified.

The EGTT feature must be turned ON before enttype=gttset parameter can be specified.

Notes

None

Output

Note:

Refer to Measurements Reference for the current release for rept-ftp-meas output examples.

 rept-ftp-meas:type=mtcd:enttype=gttapath


    tekelecstp 10-02-11 15:31:25 EST  EAGLE 42.0.0
    FTP measurement report request sent to primary MCP.
    tekelecstp 10-02-11 15:31:25 EST  EAGLE 42.0.0
    Measurement Server Connection Successful
    tekelecstp 10-02-11 15:31:25 EST  EAGLE 42.0.0
    REPT-FTP-MEAS request was successful. 
;

rept-ftp-meas:type=systot:enttype=sip


    tekelecstp 12-07-27 13:12:38 EST EAGLE 45.0.0
    rept-ftp-meas:type=systot:enttype=sip
    Command entered at terminal #4.
;


        tekelecstp 12-07-27 13:12:38 EST EAGLE 45.0.0
    FTP measurement report request sent to primary MCP.
;


    tekelecstp 12-07-27 13:12:38 EST EAGLE 45.0.0
    REPT-FTP-MEAS request was successful.
;


		  rept-ftp-meas:type=mtcd:enttype=deir


    tekelecstp 13-03-15 13:12:38 EST EAGLE 45.1.0
    rept-ftp-meas:type=mtcd:enttype=deir
    Command entered at terminal #4.


    tekelecstp 13-03-15 13:12:38 EST EAGLE 45.1.0
    FTP measurement report request sent to primary MCP.

 
   tekelecstp 13-03-15 13:12:38 EST EAGLE 45.1.0
    REPT-FTP-MEAS request was successful.


		  rept-ftp-meas:type=mtcd:enttype=enum


    tekelecstp 14-05-15 13:12:38 EST EAGLE 46.1.0
    rept-ftp-meas:type=mtcd:enttype=enum
    Command entered at terminal #4.
;

    tekelecstp 14-05-15 13:12:38 EST EAGLE 46.1.0
    FTP measurement report request sent to primary MCP.
;

    tekelecstp 14-05-15 13:12:38 EST EAGLE 46.1.0
    REPT-FTP-MEAS request was successful.
;

rept-ftp-meas:type=mtcd:enttype=sfthrot


    tekelecstp 15-04-15 13:12:38 EST EAGLE 46.3.0
    rept-ftp-meas:type=mtcd:enttype=sfthrot
    Command entered at terminal #4.
    tekelecstp 15-04-15 13:12:38 EST EAGLE 46.3.0
    FTP measurement report request sent to primary MCP.
 
    tekelecstp 15-04-15 13:12:38 EST EAGLE 46.3.0
    REPT-FTP-MEAS request was successful
;

rept-ftp-meas:type=mtcd:enttype=gttset

tekelecstp 17-05-11 15:12:30 EST EAGLE 46.6.0
    rept-ftp-meas:type=mtcd:enttype=gttset
    Command entered at terminal #4.
    tekelecstp 17-05-11 15:12:30 EST EAGLE 46.6.0
    FTP measurement report request sent to primary MCP.
 
    tekelecstp 17-05-11 15:12:30 EST EAGLE 46.6.0
    REPT-FTP-MEAS request was successful
;

Related Topics

rept-meas