4.419 rept-stat-mfc
Use this command to obtain the status of the Message Flow Control (MFC) services.
Parameters
- reset (optional)
- This parameter resets the statistics for all sample periods for the specified service.
- service (optional)
- The MFC service for which information is reported.
- Range:
-
- eroute
- EROUTE MFC service
- inm
- INM MFC service
- mtp3
- MTP3 MFC service
- scpdn
- SCCP DN MFC service
- scpelap
- SCCP ELAP MFC service
- scpepap
- SCCP EPAP MFC service
- scpimsi
- SCCP IMSI MFC service
- sfapp
- SFAPP MFC service
- sflog
- SFLOG MFC service
- sfr
- SFAPP response MFC service
- snm
- SNM MFC service
- vsccp
- VSCCP MFC service
- deirsccp
- DEIR SCCP MFC service
Example
rept-stat-mfc
rept-stat-mfc:service=vsccp:mode=act
rept-stat-mfc:service=eroute
rept-stat-mfc:service=eroute:reset=yes
rept-stat-mfc:mode=stats:service=vsccp:sample=avg30s
rept-stat-mfc:mode=stats:service=scpimsi:sample=avg30s
rept-stat-mfc:service=scpepap
rept-stat-mfc:service=scpelap
rept-stat-mfc:service=sflog
rept-stat-mfc:service=sfapp
rept-stat-mfc:service=sfr
rept-stat-mfc:service=deirsccp
Dependencies
No other command can be in progress when this command is entered.
The mode=stats and sample parameters must be specified together in the command.
If the mode or reset parameter is specified, then the service parameter must be specified.
If a value of mtp3, snm, or inm is specified for the appl parameter, then the mode=act parameter cannot be specified.
The EPAP Data Split feature must be enabled before a value of scpdn or scpimsi can be specified for the service parameter.
The Dual ExAP Config feature must be enabled before a value of scpepap or scpelap can be specified for the service parameter.
The Dual ExAP Config feature or EPAP Data Split feature must be enabled before a value of scpepap can be specified.
Notes
For the SFLOG MFC service, a maximum of two servers can be provisioned in the EAGLE, and only one can be active at a time. This command will provide the basic statistics (i.e., service denied, PDU discard, PDU sent) for the SFLOG MFC service.
Output
Abbreviated output is indicated by 3 vertical dots as shown:
.
.
.
If the card does not support thermal monitoring, and if an MFC service
is hosted on that card, then N/A is shown in the THERMAL column for that card
location in rept-stat-mfc:mode=act output.
The UNAVL state
in the output of rept-stat-mfc:mode=full indicates
the cards that are not in the IS-NR state.
This example shows an MFC report for all the services when EPAP Data Split feature is enabled:
rept-stat-mfc
tklc1141203 22-10-24 04:20:43 EST EAGLE 47.1.0.0.0-79.14.0
Service Type Total
------------------------------
SNM SYSTEM 3
INM SYSTEM 3
MTP3 SERVER 0
MTP3 CLIENT 3
EROUTE SERVER 0
EROUTE CLIENT 2
VSCCP SERVER 3
VSCCP CLIENT 0
SCPDN SERVER 3
SCPDN CLIENT 0
SCPIMSI SERVER 2
SCPIMSI CLIENT 0
SCPEPAP SERVER 2
SCPEPAP CLIENT 0
SFLOG SERVER 0
SFLOG CLIENT 3
SFAPP SERVER 0
SFAPP CLIENT 3
SFR SERVER 0
SFR CLIENT 3
DEIRSCCP SERVER 2
DEIRSCCP CLIENT 1
------------------------------
Command Completed.
;
This example shows an MFC report for all the services when Dual ExAP Config feature is enabled:
rept-stat-mfc
tklc1141203 22-10-24 04:48:03 EST EAGLE 47.1.0.0.0-79.14.0
Service Type Total
------------------------------
SNM SYSTEM 3
INM SYSTEM 3
MTP3 SERVER 0
MTP3 CLIENT 3
EROUTE SERVER 0
EROUTE CLIENT 2
VSCCP SERVER 3
VSCCP CLIENT 0
SCPELAP SERVER 0
SCPELAP CLIENT 0
SCPEPAP SERVER 2
SCPEPAP CLIENT 0
SFLOG SERVER 0
SFLOG CLIENT 3
SFAPP SERVER 0
SFAPP CLIENT 3
SFR SERVER 0
SFR CLIENT 3
DEIRSCCP SERVER 2
DEIRSCCP CLIENT 1
------------------------------
Command Completed.
;
This example shows a full report for the EROUTE MFC service:
rept-stat-mfc:service=eroute:mode=full
rlghncxa03w 11-03-04 13:46:07 EST EAGLE 44.0.0
LOC SERVICE STATE SERVER CLIENT
---------------------------------------
1101 EROUTE IS-NR X
1103 EROUTE UNAVL X
1105 EROUTE UNAVL X
1106 EROUTE IS-NR X
1113 EROUTE IS-NR X
1115 EROUTE UNAVL X
---------------------------------------
Totals 6 2 4
Command Completed.
;This example shows the EROUTE service 30 second average data calculated over the previous 5 minutes:
rept-stat-mfc:service=eroute:mode=stats:sample=avg30s
rlghncxa03w 11-03-04 14:36:07 EST EAGLE 44.0.0
PER CARD EROUTE SERVER DATA, 30-SEC AVG VALUES CALCULATED OVER PREV 5 MIN
SRVC_RQSTS_RCVD NUM_APPL_ORIG
FC MSEC ----------------------------- --------------------
EVENTS IN FC OUT_FC IN_FC DACT DACTS FC
---------------------------------------------------------------------------
0 0 568 0 0 0 0
CARD LOC: 1217 LAST 5 CLIENTS: 1101,1308,1308,1102,1102
0 0 0 0 0 0 0
CARD LOC: 1218 LAST 5 CLIENTS: 0 ,0 ,0 ,0 ,0
---------------------------------------------------------------------------
TOTAL SRVC RQSTS RCVD: 568
PER CARD EROUTE CLIENT DATA, 30-SEC AVG VALUES CALCULATED OVER PREV 5 MIN
SVC SVC PDUS PDUS SRVR ON_SHLF
RQSTS DENIED SENT DSCRD RESLCTD NOT_AVL
---------------------------------------------------------------------------
95 0 195 0 0 0
CARD LOC: 1101 LAST 5 SERVERS: 1217,0 ,0 ,0 ,0
96 0 196 0 0 0
CARD LOC: 1102 LAST 5 SERVERS: 1217,0 ,0 ,0 ,0
96 0 96 0 0 0
CARD LOC: 1103 LAST 5 SERVERS: 1217,0 ,0 ,0 ,0
47 0 47 0 0 0
CARD LOC: 1308 LAST 5 SERVERS: 1217,0 ,0 ,0 ,0
---------------------------------------------------------------------------
SYSTEM TOTALS: PDUs SENT = 1326690530, PDUs DSCRD = 94670548
Command Completed.
;This example shows the MFC status of all the EROUTE Service Cards:
rept-stat-mfc:appl=eroute:mode=act
rlghncxa03w 11-03-04 15:26:07 EST EAGLE 44.0.0
PER CARD EROUTE SERVER ACTIVATION DATA
IP LINK
LOC STATUS THERMAL STATUS
---------------------------------------
1201 ACT OK OK
1202 ACT N/A OK
1204 UNAVL --- ---
2215 DACT BAD OK
2216 DACT N/A BAD
4214 ACT OK OK
4215 DACT OK BAD
---------------------------------------
Command Completed.
;This example resets the MFC engine statistics at server side and resets application level statistics at client side, for the EROUTE service:
rept-stat-mfc:service=eroute:reset=yes
rlghncxa03w 11-03-06 13:36:07 EST EAGLE 44.0.0
Command Completed.
;
This example shows the MFC report for the EROUTE service.
rept-stat-mfc:service=eroute
rlghncxa03w 11-03-04 13:37:27 EST EAGLE 44.0.0
Service Type Total
------------------------------
EROUTE SERVER 2
EROUTE CLIENT 4
------------------------------
Command Completed.
;This example shows the MFC status of all the VSCCP Service Cards. This example displays abbreviated output.
rept-stat-mfc:service=vsccp:mode=act
rlghncxa03w 11-03-04 13:36:57 EST EAGLE 44.0.0
PER CARD VSCCP SERVER ACTIVATION DATA
LOC STATUS THERMAL
--------------------------
1201 ACT OK
1204 UNAVL ---
1217 ACT OK
2215 ACT N/A
.
.
.
4214 ACT OK
--------------------------
Command Completed.
;This example shows the MTP3 service 30 second average data calculated over the previous 5 minutes: The server stats will be shown as "-" for SCCP card location.
rept-stat-mfc:service=mtp3:mode=stats:sample=avg30s
rlghncxa03w 11-03-04 11:36:07 EST EAGLE 44.0.0
PER CARD MTP3 SYSTEM DATA, 30-SEC AVG VALUES CALCULATED OVER PREV 5 MIN
SERVER STATS CLIENT STATS
-------------------------- -----------------------------
FC MSEC PDUS PDUS PDUS SRV REQ
LOC EVENTS IN FC RCVD SENT DSCRD DENIED
---------------------------------------------------------------------------
1101 0 0 0 0 0 0
1103 0 0 0 0 0 0
1107 0 0 0 0 0 0
1207 - - - 0 0 0
1208 0 0 0 0 0 0
1211 0 0 0 0 0 0
1212 0 0 0 0 0 0
1213 0 0 0 0 0 0
1214 0 0 0 0 0 0
1215 - - - 0 0 0
1216 - - - 0 0 0
1301 0 0 0 0 0 0
1305 0 0 0 0 0 0
1306 0 0 0 0 0 0
1307 0 0 0 0 0 0
1308 0 0 0 0 0 0
1311 0 0 0 0 0 0
1312 0 0 0 0 0 0
1313 0 0 0 0 0 0
1315 0 0 0 0 0 0
---------------------------------------------------------------------------
Command Completed.
;This example shows a full MFC report for the SNM service:
rept-stat-mfc:service=snm:mode=full
rlghncxa03w 11-03-04 13:36:07 EST EAGLE 44.0.0
LOC SERVICE STATE SYSTEM
--------------------------------
1101 SNM IS-NR X
1103 SNM UNAVL X
1107 SNM IS-NR X
1111 SNM UNAVL X
--------------------------------
Totals 4 4
Command Completed.
;This example shows the SNM service 30 second average data calculated over the previous 5 minutes:
rept-stat-mfc:service=snm:mode=stats:sample=avg30s
rlghncxa03w 11-03-04 13:36:07 EST EAGLE 44.0.0
PER CARD SNM SYSTEM DATA, 30-SEC AVG VALUES CALCULATED OVER PREV 5 MIN
SERVER STATS CLIENT STATS
-------------------------- -----------------------------
FC MSEC PDUS PDUS PDUS SRV REQ
LOC EVENTS IN FC RCVD SENT DSCRD DENIED
---------------------------------------------------------------------------
1101 0 0 0 0 0 0
1103 0 0 0 0 0 0
1107 0 0 0 0 0 0
1207 0 0 0 0 0 0
1208 0 0 0 0 0 0
1211 0 0 0 0 0 0
1212 0 0 0 0 0 0
1213 0 0 0 0 0 0
1214 0 0 0 0 0 0
1215 0 0 0 0 0 0
1216 0 0 0 0 0 0
1301 0 0 0 0 0 0
1305 0 0 0 0 0 0
1306 0 0 0 0 0 0
1307 0 0 0 0 0 0
1308 0 0 0 0 0 0
1311 0 0 0 0 0 0
1312 0 0 0 0 0 0
1313 0 0 0 0 0 0
1315 0 0 0 0 0 0
---------------------------------------------------------------------------
Command Completed.
;This example shows an MFC report for the MTP3 service:
rept-stat-mfc:service=mtp3:mode=full
rlghncxa03w 11-03-04 13:06:07 EST EAGLE 44.0.0
LOC SERVICE STATE SERVER CLIENT
---------------------------------------
1101 MTP3 IS-NR X X
1103 MTP3 UNAVL X X
1107 MTP3 IS-NR X
1111 MTP3 UNAVL X
---------------------------------------
Totals 6 2 4
Command Completed.
;This example shows an MFC report for the SCPEPAP service when Dual ExAP Config feature is enabled.
rept-stat-mfc:service=scpelap:mode=full
rlghncxa03w 11-03-04 13:06:07 EST EAGLE 45.0.0
LOC SERVICE STATE SERVER CLIENT
--------------------------------------------
1105 SCPELAP IS-NR X
--------------------------------------------
Totals 1 1 0
Command Completed.
;This example shows an MFC report for the SFLOG service:
rept-stat-mfc:service=sflog:mode=full
tekelecstp 15-03-04 13:06:07 EST EAGLE 46.3.0
LOC SERVICE STATE SERVER CLIENT
--------------------------------------------
1101 SFLOG IS-NR X
--------------------------------------------
Totals 1 0 1
Command Completed.
;
This example shows an MFC report for the SFAPP service:
rept-stat-mfc:service=sfapp:mode=full
tklc1110801 18-09-25 17:06:13 EST EAGLE 46.7.0.0.0-75.14.0
rept-stat-mfc:service=sfapp:mode=full
Command entered at terminal #2.
;
tklc1110801 18-09-25 17:06:13 EST EAGLE 46.7.0.0.0-75.14.0
LOC SERVICE STATE SERVER CLIENT
---------------------------------------
1101 SFAPP IS-NR X
1102 SFAPP IS-NR X
1103 SFAPP IS-NR X
1105 SFAPP IS-NR X
1217 SFAPP IS-NR X
---------------------------------------
Totals 5 3 2
Command Completed.
;
This example shows an MFC report for the SFR service:
rept-stat-mfc:service=sfr :mode=full
Command Accepted - Processing
tklc1110801 18-09-25 17:07:45 EST EAGLE 46.7.0.0.0-75.14.0
rept-stat-mfc:service=sfr :mode=full
Command entered at terminal #2.
;
tklc1110801 18-09-25 17:07:45 EST EAGLE 46.7.0.0.0-75.14.0
LOC SERVICE STATE SERVER CLIENT
---------------------------------------
1101 SFR IS-NR X
1102 SFR IS-NR X
1103 SFR IS-NR X
1105 SFR IS-NR X
1217 SFR IS-NR X
---------------------------------------
Totals 5 3 2
Command Completed.
;
This example shows an MFC report for the DEIRSCCP service:
rept-stat-mfc:service=deirsccp:mode=full
Command Accepted - Processing
tklc1141203 22-10-23 21:18:28 EST EAGLE 47.1.0.0.0-79.14.0
rept-stat-mfc:service=deirsccp:mode=full
Command entered at terminal #1.
;
tklc1141203 22-10-23 21:18:28 EST EAGLE 47.1.0.0.0-79.14.0
LOC SERVICE STATE SERVER CLIENT
---------------------------------------
1101 DEIRSCCP IS-NR X
1102 DEIRSCCP IS-NR X
1104 DEIRSCCP IS-NR X
---------------------------------------
Totals 3 2 1
Command Completed.
;
Legend
The MFC Engine provides Server card statistics that are computed every hour (based on a Server card's timer); therefore they are typically posted an hour later. Client card statistics update continuously; current values will be observed at every invocation of the command.