4.427 rept-stat-sccp
Use this command to display the following types of reports:
rept-stat-sccp(with no parameters)—displays the status of the Service Module cards and the services executing on those cards:- A-Port (IS41 Mobile Number Portability)
- AIQ (IS41 Analyzed Information Query)
- ATINPQ (ATI Number Portability Query)
- EIR (Equipment Identity Register)
- G-Flex (GSM Flexible Numbering)
- G-Port (GSM Mobile Number Portability)
- GTT (Global Title Translation)
- IAR (Info Analyzed Relay)
- IDP Relay (Prepaid IDP Query Relay)
- IGM (IS41 GSM Migration)
- INP (INAP-based Number Portability)
- INPMR (INP Message Relay)
- LNP (Local Number Portability)
- LNPMR (LNP Message Relay)
- LRNQT (ITU TCAP LRN Query)
- MNPSMS (Portability Check for Mobile Originated SMS)
- MO SMS B-Party Routing
- MO SMS IS41-to-GSM Migration
- MO-based GSM SMS NP
- MO-based IS41 SMS NP
- MTPRTD (MTP Routed messages serviced by the SCCP card)
- PPSMS (Prepaid SMS Intercept)
- TLNP (Triggerless LNP)
- TTR (Triggerless TCAP Relay)
- V-Flex (Voice Mail Router)
- CAT2 (Category 2 Validation)
The command also displays any cards that are denied SCCP service.
rept-stat-sccp:mode=perf—targets the general SCCP traffic performance for Service Module cards. The report supplies message rates for message flow control (MFC) performance.rept-stat-sccp:loc=nnnn—provides a detailed view of the status of SCCP services provided by a specific Service Module card
Note:
Therept-stat-sccp and
rept-stat-sccp:mode=perf reports
include the status of the Service Module cards (E5-SM8G-B and SLIC cards) but
do not differentiate between the card types.
Note:
To retrieve traffic statistics for the LNP feature, therept-stat-lnp command can also be
used.
Note:
Statistics are displayed for the supported features as follows:- AIQ—AIQ Subsystem Report and Service Statistics
- APORT, GPORT, and IGM—MNP Service Statistics
- ATINPQ—ATINPQ Subsystem Report and Service Statistics
- EIR—EIR Subsystem Report and Service Statistics
- G-Flex—GFLEX Service Statistics
- GTT—GTT Service Statistics
- IAR—IAR Service Statistics
- IDP Relay—IDPR Service Statistics
- INPQ—INP Subsystem Report and Service Statistics (includes INPQ and INPMR - AINPQ is combined with INPQ)
- INPMR-INP Message Relay Service Statistics
- LNP—LNP Subsystem Report and Service Statistics (including LNPMR, LNPQS, WNPQS, TLNP, PLNPQS and LRNQT)
- LNPMR-LNP Message Relay Service Statistics
- LNPQS-LNP Query Service Statistics
- MO SMS IS41-to-GSM Migration, MO-based GSM SMS NP, MO-based IS41 SMS NP, PPSMS—SMSMR Service Statistics
- MTPRTD-MTP Routed (MTP routed messages serviced by the SCCP card) Statistics.
- TLNP-Triggerless LNP Service Statistics
- TTR-Triggerless TCAP Relay Service Statistics
- V-Flex—VFLEX Subsystem Report and Service Statistics
- WNPQS-Wireless LNP Query Service Statistics
- CAT2- Category 2 Validation Statistics
Note:
If traffic is being generated while Service Module cards are loading, then superfluous counts may be displayed in Daily and Overall Peak SCCP Loads. To correct this occurrence, reset the Peak SCCP Loads using therept-stat-sccp:peakreset=yes command.
Note:
It will also include the statistics of GTT-enabled LIM cards. If the system has both SCCP and GTT-enabled LIM cards, then it shows the statistics for both cards.Parameters
- appl (optional)
- Used to display the statistics of either SCCP cards
or GTT-enabled IPSG cards.
Note:
Usingdata=gtt, the user is able to see stats of all cards configured withdata=gtt, as in all SM GTT cards, as well as GTT-enabled IPSG cards. With the appl parameter, the user can either see stats of SCCP cards with GTT data or stats of GTT-enabled IPSG cards. - data (optional)
- The subsystem data type used in the report.
- card (optional)
- Used to display statistics of either SCCP cards or
GTT-enabled LIM cards.
Note:
Usingdata=gtt, the stats of all cards configured withdata=gtt, (SM GTT cards as well as GTT-enabled LIM cards) are displayed. With the CARD parameter, the stats of SCCP cards or stats of GTT-enabled LIM cards are displayed.
- loc (optional)
- The location of the Service Module card to be
reported on.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
- Default:
- Report a summary of all cards.
Example
rept-stat-sccp
rept-stat-sccp:mode=perf
rept-stat-sccp:loc=1106
rept-stat-sccp:data=epap
rept-stat-sccp:data=gtt:card=lim
Dependencies
No other
rept-stat-xxx command can be in
progress when this command is entered.
A Service Module card running the VSCCP application must be configured before this command can be entered.
Only one optional parameter at a time can be specified in the command. The parameters DATA, LOC and CARD are mutually exclusive.
The value specified for the loc parameter must identify a configured Service Module card running the VSCCP application or a GTT-enabled IPSG card running the IPSG32 GPL.
The EPAP Data Split feature must be enabled before the data parameter can be specified.
The Dual ExAP Config feature must be enabled before specifying parameter DATA = ELAP/EPAP.
The Dual ExAP Config feature or EPAP Data Split feature must be enabled before a value of DATA=EPAP can be specified.
Notes
In Release 46.5, with the introduction of GTT on LIM,
the output format of the
rept-stat-sccp command has been
changed. The output has been divided into three parts: head, body and tail. The
head of the output informs about the status report, primary state, secondary
state, alarms, and other information.
The body of the output depends on whether or not an SM/GTT-enabled IPSG card is present in EAGLE. If there are only SM cards in the EAGLE, the body of the output will display only the SCCP Subsystem Report. This report will contain information including daily peak load, total system capacity, number of equipped SM cards, number of in-service SM cards, and other information. It will also contain the card list of SM cards and MSU usage, as well as CPU usage of each individual card. If there are only GTT-enabled IPSG cards in the EAGLE, the body of the output will display only the GTT on LIM Report. This report will contain information including number of equipped and in-service GTT-enabled IPSG cards, total GTT on LIM capacity, and a card list of GTT-enabled IPSG cards and MSU/CPU usage of each individual card. If both SM and GTT-enabled IPSG cards are present, the output will be a combination of an SCCP Subsystem Report and GTT on LIM report.
The tail of the output informs about the Total Service Statistics of enabled services on the EAGLE. The GTT service statistics will be a combination of GTT statistics obtained from SM cards as well as from GTT-enabled IPSG cards.
Output
If the EIR, G-Port, INP, 1100 TPS/DSM for ITU NP, AINPQ, A-Port, IGM, Throughput Capacity, IAR, or V-Flex features are enabled, then the ansigflex system option is disabled.
Note:
Output for this command displays the status for services associated with features that are enabled and turned on. If a feature is not turned on, then the services for that feature are not displayed. The following examples display output when all possible features are turned on.This example shows a summary report for all the features corresponding to EPAP-based services and subsystems:
rept-stat-sccp
tekelecstp 10-04-06 18:02:43 EST EAGLE5 42.0.0
SCCP SUBSYSTEM REPORT IS-ANR Active -----
SCCP ALARM STATUS = *C 0453 Exceeded Service Error Threshold Lvl 2
GFLEX SERVICE REPORT IS-ANR Active -----
GFLEX ALARM STATUS = * 0527 Service abnormal
MNP SERVICE REPORT IS-NR Active -----
MNP ALARM STATUS = No Alarms
INPQ SUBSYSTEM REPORT OOS-MT Unavail -----
INPQ: SSN STATUS = ---------- MATE SSN STATUS = ----------
INP ALARM STATUS = *C 0395 INP Subsystem is not available
EIR SUBSYSTEM REPORT OOS-MT Unavail -----
EIR: SSN STATUS = ---------- MATE SSN STATUS = ----------
EIR ALARM STATUS = *C 0455 EIR Subsystem is not available
VFLEX SUBSYSTEM REPORT OOS-MT Unavail -----
VFLEX: SSN STATUS = ---------- MATE SSN STATUS = ----------
VFLEX ALARM STATUS = *C 0551 VFLEX Subsystem is not available
ATINPQ SUBSYSTEM REPORT OOS-MT Unavail -----
ATINPQ: SSN STATUS = ---------- MATE SSN STATUS = ----------
ATINPQ ALARM STATUS = *C 0565 ATINPQ Subsystem is not available
AIQ SUBSYSTEM REPORT IS-NR Active -----
AIQ: SSN STATUS = Allowed MATE SSN STATUS = ----------
AIQ ALARM STATUS = No Alarms
SCCP Cards Configured= 1 Cards IS-NR= 1
System Daily Peak SCCP Load 8 TPS 10-01-06 18:00:03
System Overall Peak SCCP Load 8 TPS 00-00-00 00:00:00
System Total SCCP Capacity 2550 TPS (2550 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 2040 TPS ( 80% System N SCCP Capacity)
CARD VERSION PST SST AST MSU CPU
USAGE USAGE
------------------------------------------------------------------
1101 P 007-013-002 IS-NR Active ----- 45% 45%
------------------------------------------------------------------
SCCP Service Average MSU Capacity = 45% Average CPU Capacity = 45%
AVERAGE CPU USAGE PER SERVICE:
GTT = 15% GFLEX = 5% MNP = 10% SMSMR = 10% IDPR = 0%
IAR = 0% MTPRTD = 1%
INPMR = 2% INPQ = 3% EIR = 0% VFLEX = 0% ATINPQ = 0%
AIQ = 0%
TOTAL SERVICE STATISTICS:
FAIL REROUTE\ FORWARD
SERVICE SUCCESS ERRORS RATIO WARNINGS TO GTT TOTAL
GTT: 1995 5 0% - - 2000
GFLEX: 500 1 0% 4 10 515
MNP: 800 0 0% 2 3 805
SMSMR: 67 23 25% 12 14 116
IDPR: 0 0 0% 0 0 0
IAR: 0 0 0% 0 0 0
MTPRTD: 6 0 0% - - 6
INPMR: 50 5 0% 0 15 70
INPQ: 499 1 0% 0 - 500
EIR: 0 0 0% - - 0
VFLEX: 0 0 0% - - 0
ATINPQ: 0 0 0% - - 0
AIQ: 0 0 0% - - 0
Command Completed.
;
This example shows the output for a card location for features corresponding to EPAP-based services and subsystems:
rept-stat-sccp:loc=1101
tekelecstp 10-04-06 19:41:33 EST EAGLE5 42.0.0
CARD VERSION TYPE PST SST AST
1101 127-038-000 DSM IS-NR Active -----
CARD ALARM STATUS = No Alarms
GTT: STAT = ACT CPU USAGE = 10%
GFLEX: STAT = ACT CPU USAGE = 10%
MNP: STAT = ACT CPU USAGE = 10%
SMSMR: STAT = ACT CPU USAGE = 20%
IDPR: STAT = ------- CPU USAGE = 0%
IAR: STAT = ------- CPU USAGE = 0%
MTPRTD: STAT = ACT CPU USAGE = 10%
INPMR: STAT = ------- CPU USAGE = 0%
INPQ: STAT = ------- CPU USAGE = 0%
EIR: STAT = ------- CPU USAGE = 0%
VFLEX: STAT = ------- CPU USAGE = 0%
ATINPQ: STAT = ------- CPU USAGE = 0%
AIQ: STAT = ------- CPU USAGE = 0%
---------------
TOTAL = 50%
CARD SERVICE STATISTICS
SERVICE SUCCESS ERRORS WARNINGS FORWARD TO GTT TOTAL
GTT: 1995 5 - - 2000
GFLEX: 500 1 4 10 515
MNP: 500 1 4 10 515
SMSMR: 50 2 3 15 70
IDPR: 0 0 0 0 0
IAR: 0 0 0 0 0
MTPRTD: 6 0 - - 6
INPMR: 0 0 0 0 0
INPQ: 0 0 0 - 0
EIR: 0 0 - - 0
VFLEX: 0 0 - - 0
ATINPQ: 0 0 - - 0
AIQ: 0 0 - - 0
Command Completed.
;
This example shows a performance report for the EPAP-based services:
rept-stat-sccp:mode=perf
tekelecstp 11-03-06 17:32:58 EST EAGLE5 44.0.0
SCCP SUBSYSTEM REPORT IS-NR Active -----
SCCP ALARM STATUS = No Alarms
GFLEX SERVICE REPORT IS-NR Active -----
GFLEX ALARM STATUS = No Alarms
MNP SERVICE REPORT IS-NR Active -----
MNP ALARM STATUS = No Alarms
SCCP Cards Configured= 1 Cards IS-NR= 1
System Daily Peak SCCP Load 0 TPS 11-03-06 17:23:29
System Overall Peak SCCP Load 0 TPS 00-00-00 00:00:00
System Total SCCP Capacity 6800 TPS (6800 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 5440 TPS ( 80% System N SCCP Capacity)
TPS STATISTICS
==================================================================
CARD CPU TOTAL CLASS 0 CLASS 1
USAGE MSU RATE MESSAGING RATE MESSAGING RATE
------------------------------------------------------------------
1205 5% 0 0 0
------------------------------------------------------------------
AVERAGE MSU USAGE = 0%
AVERAGE CPU USAGE = 5%
TOTAL MSU RATE = 0
STATISTICS FOR PAST 30 SECONDS
==================================================================
TOTAL MSUS: 0
TOTAL ERRORS: 0
HIGHEST 01 OVERALL DAILY PEAKS LAST 01 DAILY PEAK SCCP LOADS
===========================================================================
0 TPS 00-00-00 00:00:00 0 TPS 11-03-06 17:23:29
Command Completed.
;
This example shows a summary report for all of the features corresponding to ELAP-based subsystems:
rept-stat-sccp
tekelecstp 10-04-06 18:02:43 EST EAGLE5 42.0.0
SCCP SUBSYSTEM REPORT IS-ANR Active -----
SCCP ALARM STATUS = *C 0453 Exceeded Service Error Threshold Lvl 2
LNP SUBSYSTEM REPORT OOS-MT Unavail -----
LNP: SSN STATUS = ---------- MATE SSN STATUS = ----------
LNP ALARM STATUS = *C 0424 LNP Subsystem is not available
AIQ SUBSYSTEM REPORT IS-NR Active -----
AIQ: SSN STATUS = Allowed MATE SSN STATUS = ----------
AIQ ALARM STATUS = No Alarms
SCCP Cards Configured= 1 Cards IS-NR= 1
System Daily Peak SCCP Load 8 TPS 10-01-06 18:00:03
System Overall Peak SCCP Load 8 TPS 00-00-00 00:00:00
System Total SCCP Capacity 2550 TPS (2550 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 2040 TPS ( 80% System N SCCP Capacity)
CARD VERSION PST SST AST MSU CPU
USAGE USAGE
------------------------------------------------------------------
1101 P 007-013-002 IS-NR Active ----- 45% 45%
------------------------------------------------------------------
SCCP Service Average MSU Capacity = 45% Average CPU Capacity = 45%
AVERAGE CPU USAGE PER SERVICE:
GTT = 0%
LNPMR = 20% LNPQS = 15% WNPQS = 12% TLNP = 14% PLNPQS = 19%
LRNQT = 23% AIQ = 1%
TOTAL SERVICE STATISTICS:
FAIL REROUTE\ FORWARD
SERVICE SUCCESS ERRORS RATIO WARNINGS TO GTT TOTAL
GTT: 1995 5 0% - - 2000
LNPMR: 500 1 0% - - 515
LNPQS: 800 0 0% - - 805
WNPQS: 67 23 25% - - 116
TLNP: 0 0 0% - - 0
PLNPQS: 0 0 0% - - 0
LRNQT: 50 5 0% - - 70
AIQ: 0 0 0% - - 0
Command Completed.
;
This example shows the output for a card location for all of the features corresponding to ELAP-based subsystems:
rept-stat-sccp:loc=1101
tekelecstp 10-04-06 19:41:33 EST EAGLE5 42.0.0
CARD VERSION TYPE PST SST AST
1101 127-038-000 DSM IS-NR Active -----
CARD ALARM STATUS = No Alarms
GTT: STAT = ACT CPU USAGE = 10%
LNPMR: STAT = ACT CPU USAGE = 10%
LNPQS: STAT = ACT CPU USAGE = 10%
WNPQS: STAT = ------- CPU USAGE = 0%
TLNP: STAT = ------- CPU USAGE = 0%
PLNPQS: STAT = ------- CPU USAGE = 0%
LRNQT: STAT = ------- CPU USAGE = 0%
AIQ: STAT = ------- CPU USAGE = 0%
---------------
TOTAL = 30%
CARD SERVICE STATISTICS
SERVICE SUCCESS ERRORS WARNINGS FORWARD TO GTT TOTAL
GTT: 1995 5 - - 2000
LNPMR: 500 15 - - 515
LNPQS: 500 15 - - 515
WNPQS: 0 0 - - 0
TLNP: 0 0 - - 0
PLNPQS: 0 0 - - 0
LRNQT: 0 0 - - 0
AIQ: 0 0 - - 0
Command Completed.
;
This example shows a performance report for the ELAP-based subsystems:
rept-stat-sccp:mode=perf
tekelecstp 11-03-06 17:32:58 EST EAGLE5 44.0.0
SCCP SUBSYSTEM REPORT IS-NR Active -----
SCCP ALARM STATUS = No Alarms
LNP SUBSYSTEM REPORT OOS-MT Unavail -----
LNP: SSN STATUS = ---------- MATE SSN STATUS = ----------
LNP ALARM STATUS = *C 0424 LNP Subsystem is not available
SCCP Cards Configured= 1 Cards IS-NR= 1
System Daily Peak SCCP Load 0 TPS 11-03-06 17:23:29
System Overall Peak SCCP Load 0 TPS 00-00-00 00:00:00
System Total SCCP Capacity 6800 TPS (6800 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 5440 TPS ( 80% System N SCCP Capacity)
TPS STATISTICS
==================================================================
CARD CPU TOTAL CLASS 0 CLASS 1
USAGE MSU RATE MESSAGING RATE MESSAGING RATE
------------------------------------------------------------------
1205 5% 0 0 0
------------------------------------------------------------------
AVERAGE MSU USAGE = 0%
AVERAGE CPU USAGE = 5%
TOTAL MSU RATE = 0
STATISTICS FOR PAST 30 SECONDS
==================================================================
TOTAL MSUS: 0
TOTAL ERRORS: 0
HIGHEST 01 OVERALL DAILY PEAKS LAST 01 DAILY PEAK SCCP LOADS
===========================================================================
0 TPS 00-00-00 00:00:00 0 TPS 11-03-06 17:23:29
Command Completed.
;
This example shows a summary report of SCCP subsystem:
rept-stat-sccp
tekelecstp 10-08-17 13:35:38 EDT EAGLE 42.0.0
SCCP SUBSYSTEM REPORT IS-ANR Active -----
SCCP ALARM STATUS = ** 0262 GTT Duplicate Actn processing stopped
SCCP Cards Configured= 9 Cards IS-NR= 8
System Daily Peak SCCP Load 30147 TPS 10-08-17 13:33:36
System Overall Peak SCCP Load 30147 TPS 10-08-17 13:33:36
System Total SCCP Capacity 54400 TPS (54400 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 43520 TPS ( 80% System N SCCP Capacity)
CARD VERSION PST SST AST MSU CPU
USAGE USAGE
------------------------------------------------------------------
1201 036-027-001 IS-NR Active ----- 0% 1%
1203 036-027-001 IS-NR Active ----- 0% 3%
1205 036-027-001 IS-NR Active ----- 0% 2%
1211 036-027-001 IS-NR Active ----- 0% 3%
1213 036-027-001 IS-NR Active ----- 74% 38%
1215 036-027-001 IS-NR Active ----- 100% 42%
1217 036-027-001 IS-NR Active ----- 100% 40%
1101 036-027-001 IS-NR Active ----- 100% 42%
1107 ----------- OOS-MT Isolated ----- 0% 0%
------------------------------------------------------------------
SCCP Service Average MSU Capacity = 46% Average CPU Capacity = 21%
AVERAGE CPU USAGE PER SERVICE:
GTT = 10%
TOTAL SERVICE STATISTICS:
FAIL REROUTE\ FORWARD
SERVICE SUCCESS ERRORS RATIO WARNINGS TO GTT TOTAL
GTT: 898797 0 0% - - 898797
CARDS NOT PROCESSING GTT DUPLICATE ACTION:
1215, 1217, 1101
Command Completed.
;
This example shows the output for DN data when EPAP Data Split feature is Enabled:
rept-stat-sccp:data=dn:mode=perf
epap240m 12-01-29 15:25:01 CST Eagle 45.0.0
SCCP DN SUBSYSTEM REPORT IS-ANR Active -----
SCCP ALARM STATUS = No Alarms
SCCP Cards Configured= 3 Cards IS-NR= 1
System Daily Peak SCCP Load 0 TPS 12-01-29 14:44:31
System Overall Peak SCCP Load 0 TPS 00-00-00 00:00:00
System Total SCCP Capacity 850 TPS (850 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 680 TPS ( 80% System N SCCP Capacity)
CARD VERSION PST SST AST MSU CPU DATA
USAGE USAGE TYPE
-----------------------------------------------------------------------
1101 P 099-016-000 IS-NR Active ----- 0% 1% DN
1105 ----------- OOS-MT-DSBLD MEA ----- 0% 0% COMB
1107 099-016-000 IS-ANR Standby 29% 0% 5% COMB
-----------------------------------------------------------------------
SCCP Service Average MSU Capacity = 0% Average CPU Capacity = 1%
HIGHEST 01 OVERALL DAILY PEAKS
======================================
TPS s% d% i% DATE TIME
------------------------------------
0 100/0 /0 00-00-00 00:00:00
LAST 01 DAILY PEAK SCCP LOADS
====================================
TPS s% d% i% DATE TIME
------------------------------------
0 100/0 /0 12-01-29 14:44:31
Command Completed.
;This example shows the output when Dual ExAP Config feature is Enabled:
rept-stat-sccp:data=elap:mode=perf
epap240m 12-01-29 15:25:01 CST Eagle 45.0.0
SCCP ELAP SUBSYSTEM REPORT IS-ANR Active -----
SCCP ALARM STATUS = No Alarms
SCCP Cards Configured= 3 Cards IS-NR= 1
System Daily Peak SCCP Load 0 TPS 12-01-29 14:44:31
System Overall Peak SCCP Load 0 TPS 00-00-00 00:00:00
System Total SCCP Capacity 850 TPS (850 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 4000 TPS ( 80% System N SCCP Capacity)
CARD VERSION PST SST AST MSU CPU DATA
USAGE USAGE TYPE
-----------------------------------------------------------------------
1101 P 099-016-000 IS-NR Active ----- 0% 1% ELAP
1105 ----------- OOS-MT-DSBLD MEA ----- 0% 0% ELAP
1107 099-016-000 IS-ANR Standby 29% 0% 5% ELAP
-----------------------------------------------------------------------
SCCP Service Average MSU Capacity = 0% Average CPU Capacity = 1%
HIGHEST 01 OVERALL DAILY PEAKS
=============================================
TPS sccp% epap% elap% DATE TIME
---------------------------------------------
0 100 0 0 00-00-00 00:00:00
LAST 01 DAILY PEAK SCCP LOADS
=============================================
TPS sccp% epap% elap% DATE TIME
---------------------------------------------
0 100 0 0 00-00-00 00:00:00
This example shows the output when both the Dual ExAP Config and the EPAP Data Split features are Enabled:
rept-stat-sccp:data=dn:mode=perf
epap240m 12-01-29 15:25:01 CST Eagle 45.0.0
SCCP DN SUBSYSTEM REPORT IS-ANR Active -----
SCCP ALARM STATUS = No Alarms
SCCP Cards Configured= 3 Cards IS-NR= 1
System Daily Peak SCCP Load 0 TPS 12-01-29 14:44:31
System Overall Peak SCCP Load 0 TPS 00-00-00 00:00:00
System Total SCCP Capacity 850 TPS (850 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 5000 TPS ( 80% System N SCCP Capacity)
CARD VERSION PST SST AST MSU CPU DATA
USAGE USAGE TYPE
-----------------------------------------------------------------------
1101 P 099-016-000 IS-NR Active ----- 0% 1% DN
1105 ----------- OOS-MT-DSBLD MEA ----- 0% 0% EPAP
1107 099-016-000 IS-ANR Standby 29% 0% 5% EPAP
-----------------------------------------------------------------------
SCCP Service Average MSU Capacity = 0% Average CPU Capacity = 1%
HIGHEST 01 OVERALL DAILY PEAKS
==================================================
TPS sccp% dn% imsi% elap% DATE TIME
--------------------------------------------------
0 100 0 0 0 00-00-00 00:00:00
LAST 01 DAILY PEAK SCCP LOADS
==================================================
TPS sccp% dn% imsi% elap% DATE TIME
--------------------------------------------------
0 100 0 0 0 00-00-00 00:00:00
This example shows the output when both SM and GTT-enabled IPSG cards are present:
rept-stat-sccp
eagle10614 17-04-05 13:08:22 EST EAGLE 46.5.0.0.0-70.22.0
SCCP STATUS REPORT IS-NR Active -----
SCCP ALARM STATUS = No Alarms
SCCP SUBSYSTEM REPORT:
MNP SERVICE REPORT OOS-MA Ueq -----
MNP ALARM STATUS = No Alarms
INPQ SUBSYSTEM REPORT OOS-MA Ueq -----
INPQ: SSN STATUS = ---------- MATE SSN STATUS = ----------
INP ALARM STATUS = No Alarms
EIR SUBSYSTEM REPORT OOS-MA Ueq -----
EIR: SSN STATUS = ---------- MATE SSN STATUS = ----------
EIR ALARM STATUS = No Alarms
ATINPQ SUBSYSTEM REPORT OOS-MA Ueq -----
ATINPQ: SSN STATUS = ---------- MATE SSN STATUS = ----------
ATINPQ ALARM STATUS = No Alarms
SCCP Cards Configured= 1 Cards IS-NR= 1
System Daily Peak SCCP Load 0 TPS 17-04-05 12:48:05
System Overall Peak SCCP Load 0 TPS 00-00-00 00:00:00
System Total SCCP Capacity 5500 TPS (5500 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 4400 TPS ( 80% System N SCCP Capacity)
CARD VERSION PST SST AST MSU CPU DATA
USAGE USAGE TYPE
-----------------------------------------------------------------------
1103 073-023-009 IS-NR Active ----- 0% 1% GTT
-----------------------------------------------------------------------
SCCP Service Average MSU Capacity = 0% Average CPU Capacity = 1%
AVERAGE CPU USAGE PER SERVICE:
GTT = 0% MNP = 0%
INPMR = 0% EIR = 0% ATINPQ = 0%
GTT on LIM REPORT:
GTT LIM Cards Configured= 1 Cards IS-NR= 1
System Total GTT on LIM Cap. 10000 TPS
CARD VERSION PST SST AST MSU CPU DATA
USAGE USAGE TYPE
-----------------------------------------------------------------------
1101 073-025-017 IS-NR Active ----- 13% 12% GTT
-----------------------------------------------------------------------
SCCP Service Average MSU Capacity = 13% Average CPU Capacity = 12%
AVERAGE CPU USAGE PER SERVICE:
GTT = 2%
TOTAL SERVICE STATISTICS:
FAIL REROUTE\ FORWARD
SERVICE SUCCESS ERRORS RATIO WARNINGS TO GTT TOTAL
GTT: 40275 0 0% - - 40275
MNP: 0 0 0% 0 0 0
INPMR: 0 0 0% 0 0 0
INPQ: 0 0 0% 0 - 0
EIR: 0 0 0% - - 0
This example shows the output for DATA GTT when both SM and GTT-enabled IPSG cards are present:
rept-stat-sccp:data=gtt
eagle10614 17-04-05 13:08:47 EST EAGLE 46.5.0.0.0-70.22.0
SCCP GTT STATUS REPORT IS-NR Active -----
SCCP ALARM STATUS = No Alarms
SCCP GTT SUBSYSTEM REPORT:
SCCP Cards Configured= 1 Cards IS-NR= 1
System Daily Peak SCCP Load 0 TPS 17-04-05 12:48:05
System Overall Peak SCCP Load 0 TPS 00-00-00 00:00:00
System Total SCCP Capacity 5500 TPS (5500 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 4400 TPS ( 80% System N SCCP Capacity)
CARD VERSION PST SST AST MSU CPU DATA
USAGE USAGE TYPE
-----------------------------------------------------------------------
1103 073-023-009 IS-NR Active ----- 0% 1% GTT
-----------------------------------------------------------------------
SCCP Service Average MSU Capacity = 0% Average CPU Capacity = 1%
AVERAGE CPU USAGE PER SERVICE:
GTT = 0%
INPMR = 0% EIR = 0% ATINPQ = 0%
GTT on LIM REPORT:
GTT LIM Cards Configured= 1 Cards IS-NR= 1
System Total GTT on LIM Cap. 10000 TPS
CARD VERSION PST SST AST MSU CPU DATA
USAGE USAGE TYPE
-----------------------------------------------------------------------
1101 073-025-017 IS-NR Active ----- 13% 12% GTT
-----------------------------------------------------------------------
SCCP Service Average MSU Capacity = 13% Average CPU Capacity = 12%
AVERAGE CPU USAGE PER SERVICE:
GTT = 2%
TOTAL SERVICE STATISTICS:
FAIL REROUTE\ FORWARD
SERVICE SUCCESS ERRORS RATIO WARNINGS TO GTT TOTAL
GTT: 40312 0 0% - - 40312
This example shows the output for CARD SM when SM cards are present:
rept-stat-sccp:card=sm
eagle10614 17-04-05 13:08:54 EST EAGLE 46.5.0.0.0-70.22.0
rept-stat-sccp:card=sm
Command entered at terminal #23.
;
Command Accepted - Processing
eagle10614 17-04-05 13:08:55 EST EAGLE 46.5.0.0.0-70.22.0
SCCP STATUS REPORT IS-NR Active -----
SCCP ALARM STATUS = No Alarms
SCCP SUBSYSTEM REPORT:
SCCP Cards Configured= 1 Cards IS-NR= 1
System Daily Peak SCCP Load 0 TPS 17-04-05 12:48:05
System Overall Peak SCCP Load 0 TPS 00-00-00 00:00:00
System Total SCCP Capacity 5500 TPS (5500 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 4400 TPS ( 80% System N SCCP Capacity)
CARD VERSION PST SST AST MSU CPU DATA
USAGE USAGE TYPE
-----------------------------------------------------------------------
1103 073-023-009 IS-NR Active ----- 0% 1% GTT
-----------------------------------------------------------------------
SCCP Service Average MSU Capacity = 0% Average CPU Capacity = 1%
AVERAGE CPU USAGE PER SERVICE:
GTT = 0% MNP = 0%
INPMR = 0% EIR = 0% ATINPQ = 0%
TOTAL SERVICE STATISTICS:
FAIL REROUTE\ FORWARD
SERVICE SUCCESS ERRORS RATIO WARNINGS TO GTT TOTAL
GTT: 0 0 0% - - 0
MNP: 0 0 0% 0 0 0
INPMR: 0 0 0% 0 0 0
INPQ: 0 0 0% 0 - 0
EIR: 0 0 0% - - 0
This example shows the output for CARD LIM when GTT-enabled IPSG cards are present:
rept-stat-sccp:card=lim
eagle10614 17-04-05 13:09:02 EST EAGLE 46.5.0.0.0-70.22.0
rept-stat-sccp:card=lim
Command entered at terminal #23.
;
Command Accepted - Processing
eagle10614 17-04-05 13:09:02 EST EAGLE 46.5.0.0.0-70.22.0
SCCP GTT STATUS REPORT IS-NR Active -----
SCCP ALARM STATUS = No Alarms
GTT on LIM REPORT:
GTT LIM Cards Configured= 1 Cards IS-NR= 1
System Total GTT on LIM Cap. 10000 TPS
CARD VERSION PST SST AST MSU CPU DATA
USAGE USAGE TYPE
-----------------------------------------------------------------------
1101 073-025-017 IS-NR Active ----- 13% 12% GTT
-----------------------------------------------------------------------
SCCP Service Average MSU Capacity = 13% Average CPU Capacity = 12%
AVERAGE CPU USAGE PER SERVICE:
GTT = 2%
TOTAL SERVICE STATISTICS:
FAIL REROUTE\ FORWARD
SERVICE SUCCESS ERRORS RATIO WARNINGS TO GTT TOTAL
GTT: 40381 0 0% - - 40381
This example shows a performance report for SCCP and GTT on LIM Subsystem when both subsystems are present:
rept-stat-sccp:mode=perf
eagle10614 17-04-05 13:09:09 EST EAGLE 46.5.0.0.0-70.22.0
rept-stat-sccp:mode=perf
Command entered at terminal #23.
;
Command Accepted - Processing
eagle10614 17-04-05 13:09:09 EST EAGLE 46.5.0.0.0-70.22.0
SCCP STATUS REPORT IS-NR Active -----
SCCP ALARM STATUS = No Alarms
SCCP SUBSYSTEM REPORT:
MNP SERVICE REPORT OOS-MA Ueq -----
MNP ALARM STATUS = No Alarms
SCCP Cards Configured= 1 Cards IS-NR= 1
System Daily Peak SCCP Load 0 TPS 17-04-05 12:48:05
System Overall Peak SCCP Load 0 TPS 00-00-00 00:00:00
System Total SCCP Capacity 5500 TPS (5500 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 4400 TPS ( 80% System N SCCP Capacity)
TPS STATISTICS
===========================================================================
CARD CPU TOTAL CLASS 0 CLASS 1 DATA
USAGE MSU RATE MESSAGING RATE MESSAGING RATE TYPE
-----------------------------------------------------------------------
1103 1% 0 0 0 GTT
-----------------------------------------------------------------------
AVERAGE MSU USAGE = 0%
AVERAGE CPU USAGE = 1%
TOTAL MSU RATE = 0
STATISTICS FOR PAST 30 SECONDS
=========================================================================
TOTAL MSUS: 0
TOTAL ERRORS: 0
HIGHEST 01 OVERALL DAILY PEAKS
====================================
TPS s% d% i% DATE TIME
------------------------------------
0 0 /0 /0 00-00-00 00:00:00
LAST 01 DAILY PEAK SCCP LOADS
====================================
TPS s% d% i% DATE TIME
------------------------------------
0 0 /0 /0 17-04-05 12:48:05
GTT on LIM REPORT:
GTT LIM Cards Configured= 1 Cards IS-NR= 1
System Total GTT on LIM Cap. 10000 TPS
IPSG GTT TPS STATISTICS
===========================================================================
CARD CPU TOTAL CLASS 0 CLASS 1 DATA
USAGE MSU RATE MESSAGING RATE MESSAGING RATE TYPE
-----------------------------------------------------------------------
1101 12% 1315 1315 0 GTT
-----------------------------------------------------------------------
AVERAGE MSU USAGE = 13%
AVERAGE CPU USAGE = 12%
TOTAL MSU RATE = 1341
This example shows a performance report for GTT on LIM Subsystem when the subsystem is present:
rept-stat-sccp:mode=perf:card=lim
eagle10614 17-04-05 13:09:31 EST EAGLE 46.5.0.0.0-70.22.0
rept-stat-sccp:mode=perf:card=lim
Command entered at terminal #23.
;
Command Accepted - Processing
eagle10614 17-04-05 13:09:32 EST EAGLE 46.5.0.0.0-70.22.0
SCCP GTT STATUS REPORT IS-NR Active -----
SCCP ALARM STATUS = No Alarms
GTT on LIM REPORT:
GTT LIM Cards Configured= 1 Cards IS-NR= 1
System Total GTT on LIM Cap. 10000 TPS
IPSG GTT TPS STATISTICS
===========================================================================
CARD CPU TOTAL CLASS 0 CLASS 1 DATA
USAGE MSU RATE MESSAGING RATE MESSAGING RATE TYPE
-----------------------------------------------------------------------
1101 12% 1335 1335 0 GTT
-----------------------------------------------------------------------
AVERAGE MSU USAGE = 13%
AVERAGE CPU USAGE = 12%
TOTAL MSU RATE = 1335
This example shows a summary report of SCCP subsystem:
rept-stat-sccp
Command Accepted - Processing
stpd1091301 18-07-11 08:30:50 MST EAGLE 46.7.0.0.0-75.4.0
rept-stat-sccp
Command entered at terminal #7.
;
stpd1091301 18-07-11 08:30:50 MST EAGLE 46.7.0.0.0-75.4.0
SCCP SUBSYSTEM REPORT IS-NR Active -----
SCCP ALARM STATUS = No Alarms
GFLEX SERVICE REPORT IS-NR Active -----
GFLEX ALARM STATUS = No Alarms
MNP SERVICE REPORT IS-NR Active -----
MNP ALARM STATUS = No Alarms
INPQ SUBSYSTEM REPORT IS-NR Active -----
INPQ: SSN STATUS = Allowed MATE SSN STATUS = ----------
INP ALARM STATUS = No Alarms
ATINPQ SUBSYSTEM REPORT IS-NR Active -----
ATINPQ: SSN STATUS = Allowed MATE SSN STATUS = ----------
ATINPQ ALARM STATUS = No Alarms
SCCP Cards Configured= 6 Cards IS-NR= 6
System Daily Peak SCCP Load 361 TPS 18-07-11 04:40:13
System Overall Peak SCCP Load 361 TPS 18-07-11 04:40:13
System Total SCCP Capacity 40800 TPS (40800 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 32640 TPS ( 80% System N SCCP Capacity)
CARD VERSION PST SST AST MSU CPU
USAGE USAGE
-----------------------------------------------------------------------
2113 145-004-000 IS-NR Active ----- 0% 2%
2201 145-004-000 IS-NR Active ----- 0% 3%
2213 145-004-000 IS-NR Active ----- 0% 2%
2217 145-004-000 IS-NR Active ----- 0% 2%
2317 145-004-000 IS-NR Active ----- 0% 2%
1111 P 145-004-000 IS-NR Active ----- 0% 2%
-----------------------------------------------------------------------
SCCP Service Average MSU Capacity = 0% Average CPU Capacity = 2%
AVERAGE CPU USAGE PER SERVICE:
GTT = 0% GFLEX = 0% MNP = 0% SMSMR = 0% IDPR = 0%
MTPRTD = 0%
INPMR = 0% ATINPQ = 0%
TOTAL SERVICE STATISTICS:
FAIL REROUTE\ FORWARD FORWARD
SERVICE SUCCESS ERROR RATIO WARNINGS TO GTT TO MATE TOTAL
GTT: 0 0 0% - - 0 0
GFLEX: 0 0 0% 0 0 0
MNP: 0 0 0% 0 0 0
SMSMR: 0 0 0% 0 0 0
IDPR: 0 0 0% 0 0 0
MTPRTD: 0 0 0% - - 0
INPMR: 0 0 0% 0 0 0
INPQ: 0 0 0% 0 - 0
ATINPQ: 0 0 0% - - 0
Command Completed.
;
This example shows a performance report for SCCP:
rept-stat-sccp:mode=perf
Command Accepted - Processing
tekelecstp 18-06-07 09:16:15 MST EAGLE 46.7.0.0.0-75.4.0
rept-stat-sccp:mode=perf
Command entered at terminal #1.
;
tekelecstp 18-06-07 09:16:15 MST EAGLE 46.7.0.0.0-75.4.0
SCCP SUBSYSTEM REPORT IS-NR Active -----
SCCP ALARM STATUS = No Alarms
SCCP Cards Configured= 1 Cards IS-NR= 1
System Daily Peak SCCP Load 0 TPS 18-06-07 00:00:01
System Overall Peak SCCP Load 20 TPS 18-06-06 11:07:10
System Total SCCP Capacity 5500 TPS (5500 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 4400 TPS ( 80% System N SCCP Capacity)
TPS STATISTICS
===========================================================================
CARD CPU TOTAL CLASS 0 CLASS 1
USAGE MSU RATE MESSAGING RATE MESSAGING RATE
-----------------------------------------------------------------------
1101 1% 0 0 0
-----------------------------------------------------------------------
AVERAGE MSU USAGE = 0%
AVERAGE CPU USAGE = 1%
TOTAL MSU RATE = 0
STATISTICS FOR PAST 30 SECONDS
=========================================================================
TOTAL MSUS: 0
TOTAL ERRORS: 0
TOTAL MSU SEND TO MATE: 0
HIGHEST 02 OVERALL DAILY PEAKS LAST 02 DAILY PEAK SCCP LOADS
===========================================================================
20 TPS 18-06-06 11:07:10 0 TPS 18-06-07 00:00:01
0 TPS 00-00-00 00:00:00 20 TPS 18-06-06 11:07:10
Command Completed.
;
This example shows a summary report of SCCP subsystem with CAT2:
> rept-stat-sccp
Command Accepted - Processing
tklc1131102 20-07-18 13:54:48 EST EAGLE 46.9.0.0.0-76.23.0
rept-stat-sccp
Command entered at terminal #3.
;
tklc1131102 20-07-18 13:54:49 EST EAGLE 46.9.0.0.0-76.23.0
SCCP SUBSYSTEM REPORT IS-NR Active -----
SCCP ALARM STATUS = No Alarms
SCCP Cards Configured= 2 Cards IS-NR= 1
System Daily Peak SCCP Load 0 TPS 20-07-18 00:00:00
System Overall Peak SCCP Load 3361 TPS 20-07-12 00:23:07
System Total SCCP Capacity 5500 TPS (5500 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 4400 TPS ( 80% System N SCCP Capacity)
CARD VERSION PST SST AST MSU CPU
USAGE USAGE
-----------------------------------------------------------------------
1101 093-023-013 IS-NR Active ----- 0% 2%
-----------------------------------------------------------------------
SCCP Service Average MSU Capacity = 0% Average CPU Capacity = 2%
AVERAGE CPU USAGE PER SERVICE:
GTT = 0%
TOTAL SERVICE STATISTICS:
FAIL REROUTE\ FORWARD FORWARD
SERVICE SUCCESS ERROR RATIO WARNINGS TO GTT TO MATE TOTAL
GTT: 0 0 0% - - 0 0
CAT2: 0 0 0% 0 - 0 0
Command Completed.
;
This example shows the output for CARD SM when SM cards are present with CAT2:
>
rept-stat-sccp:card=smCommand Accepted - Processing
tklc1131102 20-07-18 13:57:46 EST EAGLE 46.9.0.0.0-76.23.0
rept-stat-sccp:card=sm
Command entered at terminal #3.
;
tklc1131102 20-07-18 13:57:46 EST EAGLE 46.9.0.0.0-76.23.0
SCCP SUBSYSTEM REPORT IS-NR Active -----
SCCP ALARM STATUS = No Alarms
SCCP Cards Configured= 2 Cards IS-NR= 1
System Daily Peak SCCP Load 0 TPS 20-07-18 00:00:00
System Overall Peak SCCP Load 3361 TPS 20-07-12 00:23:07
System Total SCCP Capacity 5500 TPS (5500 max SCCP Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 4400 TPS ( 80% System N SCCP Capacity)
CARD VERSION PST SST AST MSU CPU
USAGE USAGE
-----------------------------------------------------------------------
1101 093-023-013 IS-NR Active ----- 0% 2%
1105 ----------- OOS-MT-DSBLD MEA ----- 0% 0%
-----------------------------------------------------------------------
SCCP Service Average MSU Capacity = 0% Average CPU Capacity = 2%
AVERAGE CPU USAGE PER SERVICE:
GTT = 0%
TOTAL SERVICE STATISTICS:
FAIL REROUTE\ FORWARD FORWARD
SERVICE SUCCESS ERROR RATIO WARNINGS TO GTT TO MATE TOTAL
GTT: 0 0 0% - - 0 0
CAT2: 0 0 0% 0 - 0 0
Command Completed.
;
This example shows the output for a card location with CAT2 of SCCP subsystem:
>
rept-stat-sccp:loc=1101Command Accepted - Processing
tklc1131102 20-07-18 14:07:26 EST EAGLE 46.9.0.0.0-76.23.0
rept-stat-sccp:loc=1101
Command entered at terminal #3.
;
tklc1131102 20-07-18 14:07:26 EST EAGLE 46.9.0.0.0-76.23.0
CARD VERSION TYPE PST SST AST
1101 093-023-013 SLIC IS-NR Active -----
CARD ALARM STATUS = No Alarms.
GTT: STAT = ACT CPU USAGE = 0%
---------------
TOTAL = 0%
CARD SERVICE STATISTICS
FORWARD FORWARD
SERVICE SUCCESS ERRORS WARNINGS TO GTT TO MATE TOTAL
GTT: 0 0 - - 0 0
CAT2: 0 0 0 - - 0
Command Completed.
;
> rept-stat-sccp
Command Accepted - Processing
tklc1121001 22-12-07 23:07:50 EST EAGLE 47.1.0.0.0-79.14.0
rept-stat-sccp
Command entered at terminal #4.
;
tklc1121001 22-12-07 23:07:50 EST EAGLE 47.1.0.0.0-79.14.0
SCCP SUBSYSTEM REPORT IS-NR Active -----
SCCP ALARM STATUS = No Alarms
MNP SERVICE REPORT OOS-MT-DSBLD Manual -----
MNP ALARM STATUS = *C 0529 Service is disabled
EIR SUBSYSTEM REPORT IS-ANR Active -----
EIR: SSN STATUS = Allowed MATE SSN STATUS = ----------
EIR ALARM STATUS = ** 0460 EIR Subsystem degraded, cards abnormal
SCCP Cards Configured= 2 Cards IS-NR= 1
System Daily Peak SCCP Load 0 TPS 22-12-07 00:00:01
System Overall Peak SCCP Load 0 TPS 00-00-00 00:00:00
System Total SCCP Capacity 10000 TPS (10000 max SCCP Capacity)
System Total SCCP DEIR Capacity 8000 TPS (8000 max SCCP DEIR Capacity)
System SCCP Capacity Calc. Method (N)
System TPS Alarm Threshold 8000 TPS ( 80% System N SCCP Capacity)
CARD VERSION PST SST AST MSU CPU DATA
USAGE USAGE TYPE
-----------------------------------------------------------------------
1106 ----------- OOS-MT-DSBLD Manual ----- 0% 0% IMSI
1108 P 076-014-000 IS-NR Active ----- 0% 2% EPAP
-----------------------------------------------------------------------
SCCP Service Average MSU Capacity = 0% Average CPU Capacity = 2%
AVERAGE CPU USAGE PER SERVICE:
GTT = 0% MNP = 0% DEIR = 0%
EIR = 0%
TOTAL SERVICE STATISTICS:
FAIL REROUTE\ FORWARD FORWARD
SERVICE SUCCESS ERROR RATIO WARNINGS TO GTT TO MATE TOTAL
GTT: 0 0 0% - - 0 0
MNP: 0 0 0% 0 0 0
CAT2: 0 0 0% 0 - 0 0
DEIR: 210 0 0% - - 250
EIR: 0 0 0% - - 0
Command Completed.
;
Legend
This section defines the fields of the three
rept-stat-sccp
reports:
rept-stat-sccpwith no parametersrept-stat-sccp:mode=perfrept-stat-sccp:loc=nnnn
A dash (-) in an output field indicates that the statistic does not apply.
Note:
The ERRORS and TOTAL ERRORS fields indicate that errors have occurred for Service Module cards in the system. Refer to UIMs generated by the system for the specific errors, and refer to the Maintenance Guide for error explanations and recovery procedures.Report
Type:
rept-stat-sccp with no parameters
- SCCP SUBSYSTEM REPORT,GTT ON LIM REPORT, GFLEX/MNP SERVICE REPORT and LNP/INPQ/EIR/VFLEX/ATINPQ/AIQ SUBSYSTEM REPORT—Summary of the SCCP subsystem status, GTT on LIM subsystem status, GFLEX and MNP service status, LNP, INPQ (INP Query), EIR, VFLEX, ATINPQ and AIQ subsystem status
- SCCP CARDS CONFIGURED—Number of provisioned Service Module cards running the VSCCP application
- GTT LIM CARDS CONFIGURED—Number of provisioned GTT-enabled LIM cards running the IPSG32 GPL
- CARD IS-NR—Number of Service Module or GTT-enabled LIM cards that can be used by the system (status is In-Service Normal, IS-NR)
- SYSTEM PEAK SCCP LOAD—Highest SCCP transactions-per-second (TPS) processed by the EAGLE
- SYSTEM TOTAL SCCP CAPACITY—Sum of the maximum capacity of all active SCCP cards
- SYSTEM TOTAL GTT ON LIM CAPACITY—Sum of the maximum capacity of all active GTT-enabled LIM cards
- SYSTEM TPS ALARM
THRESHOLD—Percentage of traffic that triggers an alarm to warn that the
EAGLE is approaching the total system SCCP transactions-per-second (TPS)
capacity. This value is set by the
chg-th-almcommand. - CARD—Card location of the cards running the VSCCP/IPSG application
- P—When G-Flex, GPORT, INP, APORT, EIR, V-Flex, IAR, or IGM feature is turned on, a P indicates the primary Service Module card. The primary Service Module card provides the MPS status to the EAGLE. This indicator is displayed between the card location and the GPL version.
- VERSION—Version number of the GPL running on the Service Module card
- PST—Primary state of the card. See Possible Values for PST/SST/AST.
- SST—Secondary state of the card. See Possible Values for PST/SST/AST.
- AST—Associated state of the card. See Possible Values for PST/SST/AST.
- MSU USAGE—Percentage of the maximum number of MSUs received by each card during the last 30 seconds
- CPU USAGE—Percentage of the amount of CPU used by each card during the last 30 seconds to process messages and to handle other foreground and background tasks
- SCCP SERVICE AVERAGE MSU CAPACITY—Average MSU capacity used over the last 30-second interval. This field includes all services provided by the Service Module or GTT-enabled LIM cards.
- AVERAGE CPU CAPACITY—Average CPU capacity used over the last 30-second interval. This field includes all services provided by the Service Module or GTT-enabled LIM cards.
- AVERAGE CPU USAGE PER SERVICE—System-wide view of the service traffic composition.
- TOTAL SERVICE
STATISTICS—System-wide view of per-service statistics
for the last 30-second interval. An "A" in the
field indicates that the statistic does not apply. The report tracks the
following information:
- SERVICE
- SUCCESS—Total number of successful messages processed by the specified card for each service. Applies to all services.
- ERRORS—Total number of messages with errors for each service. Applies to all services.
- WARNINGS—Total number of messages that output UIM warnings and were forwarded to GTT by the specified card for G-Flex, MNP, SMSMR, IDPR, IAR, INPMR and INPQ services and total number of messages for which CAT2 validation has not been applied in case of CAT2.
- FORWARD TO GTT—Total number of messages that could not find a match in the MPS database (did not produce any errors or warnings) and were successfully forwarded to GTT by the specified card for G-Flex, MNP, SMSMR, IDPR, IAR and INPMR services
- FORWARD TO MATE— Total number of ACK messages on which GTT is performed and send to mate STP.
rept-stat-sccp:mode=perf
This report includes the status of E5-SM8G-B and SLIC cards, but does not differentiate between these card types.
- SCCP SUBSYSTEM REPORT, GTT ON LIM REPORT,LNP SUBSYSTEM REPORT and GFLEX/MNP SERVICE REPORT—Summary status of the SCCP subsystem, GTT on LIM subsystem status, GFLEX and MNP services, LNP subsystem along with their corresponding Alarm Status
- SCCP CARDS CONFIGURED—Number of Service Module cards provisioned
- GTT LIM CARDS CONFIGURED—Number of provisioned GTT-enabled LIM cards running the IPSG32 GPL
- CARD IS-NR—Number of Service Module or GTT-enabled LIM cards that can be used by the system (status is in-service normal, IS-NR)
- SYSTEM PEAK SCCP LOAD—Highest SCCP TPS processed by the EAGLE
- SYSTEM TOTAL SCCP CAPACITY—Sum of the maximum capacity of all active Service Module cards
- SYSTEM TOTAL GTT ON LIM CAPACITY—Sum of the maximum capacity of all active GTT-enabled LIM cards
- SYSTEM TPS ALARM
THRESHOLD—Percentage of traffic that triggers an alarm to warn that the
EAGLE is approaching the total system SCCP TPS capacity. This value is set by
the
chg-th-almcommand. - TPS
STATISTICS—Section of the report that provides TPS statistics on each
Service Module or GTT-enabled LIM card
- CARD—Card location of the cards running the VSCCP/IPSG application
- CPU USAGE—Percentage of the amount of CPU used to process messages by each card during the last 30 seconds
- TOTAL MSU RATE—Total number of messages processed per second. This and the other message rates are obtained from statistics maintained by the Service Module card for the last 30-second period.
- CLASS 0 and CLASS 1 MESSAGING RATE—Number of messages received per second.
The next section of the
rept-stat-sccp:mode=perf
report provides system-wide SCCP traffic statistics.
- AVERAGE MSU USAGE
- Total of the MSU usage fields from each Service Module card divided by the number of active Service Module or GTT-enabled LIM cards
- AVERAGE CPU USAGE
- Total of the CPU usage fields from each Service Module card divided by the number of active Service Module or GTT-enabled LIM cards
- TOTAL MSU RATE
- Sum of all MSU rates processed by all active Service Module or GTT-enabled LIM cards
- STATISTICS FOR PAST 30 SECONDS
- Statistics that represent the last 30-second period
- TOTAL MSUS
- Sum of all transactions on all active Service Module or GTT-enabled LIM cards
- TOTAL ERRORS
- Sum of all errors on all active Service Module or GTT-enabled LIM cards
- TOTAL MSU SEND TO MATE
- Sum of all transactions that are sent to the mate STP
Report Type:
rept-stat-sccp:loc=nnnn
- CARD—Card location of the card running the VSCCP/IPSG application
- VERSION—Version number of the GPL the card is running
- TYPE—Type of the card
- PST—Primary state of the card. See Possible Values for PST/SST/AST.
- SST—Secondary state of the card. See Possible Values for PST/SST/AST.
- AST—Associated state of the card. See Possible Values for PST/SST/AST.
- CARD ALARM STATUS—If there are no card alarms present, this field displays No Alarms.
The next section of the
rept-stat-sccp:loc=nnnn
report supplies the status of the individual services
provided by the card and the associated CPU usage for the service.
- GTT: STAT
- Possible values are ACTIVE and SWDL (software loading)
- SMSMR: STAT
- Possible values are ACTIVE and SWDL (software loading)
- IDPR: STAT
- Possible values are ACTIVE and SWDL (software loading)
- IAR: STAT
- Possible values are ACTIVE and SWDL (software loading)
- INPMR: STAT
- Possible values are ACTIVE and SWDL (software loading)
- MTPRTD: STAT
- Possible values are ACTIVE and SWDL (software loading)
- GFLEX: STAT
- Possible values are ACTIVE, OFFLINE and SWDL (software loading)
- MNP: STAT
- Possible values are ACTIVE, OFFLINE, and SWDL (software loading)
- INPQ: STAT
- Possible values are ACTIVE, OFFLINE, and SWDL (software loading)
- EIR: STAT
- Possible values are ACTIVE, OFFLINE and SWDL (software loading)
- VFLEX: STAT
- Possible values are ACTIVE, OFFLINE and SWDL (software loading)
- LNPMR: STAT
- Possible values are ACTIVE, OFFLINE and SWDL (software loading)
- LNPQS: STAT
- Possible values are ACTIVE, OFFLINE and SWDL (software loading)
- WNPQS: STAT
- Possible values are ACTIVE, OFFLINE and SWDL (software loading)
- TLNP: STAT
- Possible values are ACTIVE, OFFLINE and SWDL (software loading)
- PLNPQS: STAT
- Possible values are ACTIVE, OFFLINE and SWDL (software loading)
- LRNQT: STAT
- Possible values are ACTIVE, OFFLINE and SWDL (software loading)
- ATINPQ: STAT
- Possible values are ACTIVE, OFFLINE and SWDL (software loading)
- AIQ: STAT
- Possible values are ACTIVE, OFFLINE and SWDL (software loading)
- TOTAL
- Sum of the CPU usage for the services running over the previous 30-second period
- CARD SERVICE STATISTICS
- Card service statistics over the previous 30-second period for the specified card. The report tracks the following:
- SERVICE
- Name of the individual service provided by the card
- SUCCESS
- Total number of successful messages processed by the specified card for each service. Applies to all services.
- ERRORS
- Total number of messages with errors for each service. Applies to all services.
- WARNINGS
- Total number of messages that output UIM warnings and were forwarded to GTT by the specified card for G-Flex, MNP, SMSMR, IDPR, IAR, INPMR and INPQ services and total number of messages for which CAT2 validation has not been applied in case of CAT2.
- FORWARD TO GTT
- Total number of messages that could not find a match in the MPS database (did not produce any errors or warnings) and were successfully forwarded to GTT by the specified card for G-Flex, MNP, SMSMR, IDPR, IAR, and INPMR services
- FORWARD TO MATE
- Total number of successful ACK messages that are send to mate STP by a specific card for GTT service only.
- TOTAL
- Total number of SUCCESS, ERRORS, WARNINGS, and FORWARD TO GTT messages
IMEI Challenge Legend
This section of the
rept-stat-sccp report supplies the stats for the
IMEI Challenge. The legends mean the following:
Related Topics