4.626 tst-j1
Note:
This command can be entered for E5-E1T1-B cards.Parameters
- loc (mandatory)
- The card location as stenciled on the shelf of the system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
- Default:
- All T1 card locations having J1 interfaces configured are listed.
Example
tst-j1:j1port=1:loc=1102:action=stop
Dependencies
This command cannot be entered during upgrade.
The value specified for the loc parameter must indicate an E5-E1T1-B card with card type LIMT1.
The card in the location specified by the loc parameter must be equipped.
The card in the location specified by the loc parameter must be in service.
The J1 port specified by the j1port parameter must have a defined J1 interface.
All signaling links that provide timeslots serviced by J1 interfaces on the specified card must be deactivated before this command can be entered. None of the signaling links can be running link diagnostic tests (tst-slk
and act-cdl
commands) when this command is entered.
Only one port test can be running on the J1 port specified by the j1port parameter at one time.
The J1 table must be accessible.
The action=stop parameter can be specified only when a port test is running.
If the action=stop parameter is specified, a value of feline or fepayload must be specified for the loopback parameter.
If the action=stop parameter is specified, and a value of feline or fepayload is specified for the loopback parameter, then there cannot be an active loopback for the T1 span, or the active loopback must be the one specified in the tst-t1:action=stop command.
Notes
Only one port test can be performed at a time on a J1 port. When a port test is in progress on a J1 port, subsequent test requests are rejected.
If a loopback type of feline or fepayload is specified, then the loopback requests are sent to the far end. No response is given from the far end indicate if the request was acted upon or received. The local card which hosts the J1 span in the EAGLE does not instrument the loopback locally but maintains a knowledge of the far end loopback request. If the local card boots, this knowledge is lost by the card.
To maintain the far end loopback states, if the J1 card with an active feline or fepayload test boots, the card loses any knowledge of the Far End loopback request, but the OAM retains that knowledge. If the OAM boots, the J1 card updates the OAM with its last known loopback state. If both the J1 card and the active OAM card boots while a Far End Loopback is active, then there is no way of determining the J1 state; however, a tst-j1:action=stop:action=(feline or fepayload) command can still be sent.
Output
tst-j1:j1port=1:loc=1102:action=stop
tekelecstp 13-12-19 19:02:51 EST 46.0.0-65.3.0
Command Accepted: Stop Port test message is sent.
;
tekelecstp 13-12-19 19:02:51 EST 46.0.0-65.3.0
Command Completed.
;