Documentation, Support, and Training
Network Management Connector and Pins
USB Management Connector and Pins
Preparing to Install the Gateway
Suggested Tools for Installation
Antistatic Precautions for Installation
Verify Shipping Carton Contents
Assemble the Ethernet Splitter Data Cables
Install the Gateway in the Rack
Verifying the InfiniBand Fabric
Understanding Routing Through the Gateway
Understanding Administrative Commands
Administering the I4 Switch Chip
Controlling the I4 Switch Chip
Administering Gateway Resources
Installing Gateway Supportive Software
Creating VNICs Under Gateway Manual Mode
Creating VNICs Under Host Manual Mode
Controlling Gateway Ports and Parameters
Administering the InfiniBand Fabric
Monitoring the InfiniBand Fabric
Controlling the InfiniBand Fabric
Administering the Subnet Manager
Controlling the Subnet Manager
Understanding Oracle ILOM on the Gateway
Understanding Oracle ILOM Targets
Administering Oracle ILOM (CLI)
Accessing Oracle ILOM From the CLI
Switching Between the Oracle ILOM Shell and the Linux Shell
Monitoring Oracle ILOM Targets (CLI)
Controlling Oracle ILOM Targets (CLI)
Upgrading the Gateway Firmware Through Oracle ILOM (CLI)
Administering Oracle ILOM (Web)
Access Oracle ILOM From the Web Interface
Monitoring Oracle ILOM Targets (Web)
Controlling Oracle ILOM Targets (Web)
Upgrade the Gateway Firmware (Web)
Accessing the Rear Panel Diagram
Accessing Status Pane Information
Monitoring Parameters and Status
Administering Oracle ILOM (SNMP)
Monitoring Oracle ILOM Targets (SNMP)
Controlling Oracle ILOM Targets (SNMP)
Display the Sensor States (IPMI)
Display the Sensor Information (IPMI)
Display the System Event Log (IPMI)
Display FRU ID Information (IPMI)
Display Gateway Status LED States (IPMI)
Disable the Locator LED (IPMI)
Understanding Oracle ILOM Commands
Understanding Service Procedures
Antistatic Precautions for Service
Remove the Gateway From the Rack
Understanding Hardware Commands
Linux Shells for Hardware Commands
Understanding InfiniBand Commands
Linux Shells for InfiniBand Commands
Understanding the SUN-DCS-MIB MIB OIDs
Understanding the SUN-ILOM-CONTROL-MIB MIB OIDs
Understanding the SUN-PLATFORM-MIB MIB OIDs
Sets the Subnet Manager priority.
setsmpriority priority|list
where priority is a number from 0 (lowest) to 13 (highest).
This hardware command sets the priority of the Subnet Manager within the management controller. You use this command when there are multiple Subnet Managers in the InfiniBand fabric. By setting a Subnet Manager to a higher priority than another Subnet Manager, it becomes the primary (or Master) Subnet Manager. When you set a Subnet Manager to a priority lower than another Subnet Manager, it becomes the secondary Subnet Manager. The list option provides a listing of the Subnet Manager settings in respect to priority, controlled handover, and subnet prefix.
The setsmpriority command writes the value of priority to the sm_priority parameter of the /etc/opensm/opensm.conf file.
Note - You must stop or disable the OpenSM Subnet Manager before using the setsmpriority command. See disablesm Command.
Note - Setting Subnet Managers of the same fabric to the same priority can have undesirable results.
The setsmpriority command is available from the /SYS/Fabric_Mgmt Linux shell target of the Oracle ILOM CLI interface.
The following example shows how to set the priority of the Subnet Manager to 3 using the setsmpriority command.
# setsmpriority 3 ------------------------------------------------- OpenSM 3.2.6_20090717 Reading Cached Option File: /etc/opensm/opensm.conf Loading Cached Option:routing_engine = ftree Loading Cached Option:sm_priority = 13 Loading Cached Option:sminfo_polling_timeout = 1000 Loading Cached Option:polling_retry_number = 3 Command Line Arguments: Priority = 3 Creating config file template ’/tmp/osm.conf’. Log File: /var/log/opensm.log ------------------------------------------------- #
The following example shows how to display the current settings of the Subnet Manager priority, controlled handover, and subnet prefix with the list option of the setsubnetprefix command.
# setsmpriority list smpriority 0 controlled_handover FALSE subnet_prefix 0xfe80000000000000 #