Recovering a Corrupted Disk Label

Sometimes, a power or system failure causes a disk's label to become unrecognizable. A corrupted disk label doesn't always mean that the slice information or the disk's data must be re-created or restored.

The first step to recovering a corrupted disk label is to label the disk with the correct geometry and disk type information. You can complete this step through the normal disk labeling method, by using either automatic configuration or manual disk type specification.

If the format utility recognizes the disk type, the next step is to search for a backup label to label the disk. Labeling the disk with the backup label labels the disk with the correct partitioning information, the disk type, and disk geometry.

How to Recover a Corrupted Disk Label

Boot the system to single-user mode.
If necessary, boot the system from a local Oracle Solaris DVD or the network in single-user mode to access the disk.
See Chapter 12, Booting an Oracle Solaris System (Tasks), in System Administration Guide: Basic Administration or Booting an x86 Based System by Using GRUB (Task Map) in System Administration Guide: Basic Administration for information on booting the system.
Relabel the disk.
```
# format
```
The format utility attempts to automatically configure any unlabeled SCSI disk. If the format utility is able to configure the unlabeled and corrupted disk, it will display this message:
```
cwtxdy: configured with capacity of abcMB
```
The format utility then displays a numbered list of disks on the system.
Type the number of the disk that you need to recover.
```
Specify disk (enter its number): 1
```
Select one of the following to determine how to label the disk.
- If the disk was configured successfully, follow Steps 5 and 6. Then go to step 12.
- If the disk was not configured successfully, follow Steps 7–11. Then go to step 12.

Search for the backup label.

format> verify
Warning: Could not read primary label.
Warning: Check the current partitioning and 'label' the disk or 
use the 'backup' command.
Backup label contents:
Volume name = <        >
ascii name  = <FUJITSU-MAP3147N SUN146G-0501>
pcyl        = 14089
ncyl        = 14087
acyl        =    2
nhead       =   24
nsect       =  848
Part      Tag    Flag     Cylinders         Size            Blocks
  0       root    wm       0 - 14086      136.71GB    (14087/0/0) 286698624
  1       swap    wu       0                0         (0/0/0)             0
  2     backup    wu       0 - 14086      136.71GB    (14087/0/0) 286698624
  3 unassigned    wm       0                0         (0/0/0)             0
  4 unassigned    wm       0                0         (0/0/0)             0
  5 unassigned    wm       0                0         (0/0/0)             0
  6        usr    wm       0                0         (0/0/0)             0
  7 unassigned    wm       0                0         (0/0/0)             0

If the format utility was able to find a backup label and the backup label contents appear satisfactory, use the backup command to label the disk with the backup label.
```
format> backup
Disk has a primary label, still continue? y
 
Searching for backup labels...found.
Restoring primary label
```
The disk label has been recovered. Go to Step 12.
If the format utility was not able to automatically configure the disk, specify the disk type by using the type command.
```
format> type
```
The Available Drives Type menu is displayed.
Select 0 to automatically configure the disk. Or, select a disk type from the list of possible disk types.
```
Specify disk type (enter its number)[12]: 12
```
If the disk was successfully configured, reply with no when the format utility asks if you want to label the disk.
```
Disk not labeled.  Label it now?  no
```

Use the verify command to search for backup labels.

format> verify
Warning: Could not read primary label.
Warning: Check the current partitioning and 'label' the disk
or use the 'backup' command.
.
.
.

If the format utility was able to find a backup label and the backup label contents appear satisfactory, use the backup command to label the disk with the backup label.
```
format> backup
Disk has a primary label, still continue? y
Searching for backup labels...found.
Restoring primary label
```
The disk label has been recovered.
Exit the format utility.
```
format> q
```
Verify the file systems on the recovered disk by using the fsck command.
For information on using the fsck command, see Chapter 20, Checking UFS File System Consistency (Tasks).

Skip Navigation Links
Exit Print View
	System Administration Guide: Devices and File Systems Oracle Solaris 10 8/11 Information Library