| | |
Undefined action in parameter parameter-name's action action-name
| In the IPQoS configuration file, the action name that you specified
in parameter-name does not exist in the
configuration file.
| Create the action or refer to a different, existing action in the parameter.
|
Action
action-name involved in cycle
| In the IPQoS configuration file, action-name is
part of a cycle of actions, which is not allowed by IPQoS.
| Determine the action cycle. Then, remove one of the cyclical references from the IPQoS
configuration file.
|
Action action-name isn't referenced by any other actions
| A non-ipgpc action definition is not referenced
by any other defined actions in the IPQoS configuration, which is
not allowed by IPQoS.
| Remove the unreferenced action. Alternatively, make another
action reference the currently unreferenced action.
|
Missing/Invalid config file fmt_version
| The format of the configuration file is not specified as the
first entry of the file, which is required by IPQoS.
|
|
Unsupported config file format version
| The format version that is specified in the configuration file
is not supported by IPQoS.
| Change the format version to fmt_version 1.0,
which is required beginning with the Solaris 9 9/02 release of IPQoS.
|
No ipgpc action defined.
| An action is not defined for the ipgpc classifier in the configuration
file, which is an IPQoS requirement.
|
|
Can't commit a null configuration
| ipqosconf -c was run to commit a configuration that was empty, which IPQoS
does not allow.
|
|
Invalid CIDR mask on line line-number
| In the configuration file, a CIDR mask is used as part of the IP address that is out of the
valid range for IP addresses.
| Change the mask value to be in the range of 1–32 for IPv4
and 1–128 for IPv6.
|
Address masks aren't allowed for host names
line line-number
| In the configuration file, a CIDR mask is defined for a host name, which is not allowed in
IPQoS.
| Remove the mask or change the host name to an IP address.
|
Invalid module name line line-number
| In the configuration file, the module name specified in an action statement is invalid.
| Check the spelling of the module name. For a list of IPQoS modules,
refer to Table 6–5.
|
ipgpc action has incorrect name line
line-number
| The name of the ipgpc action in the configuration file is not the required
name ipgpc.classify.
| Rename the action ipgpc.classify.
|
Second parameter clause not supported line line-number
| In the configuration file, two parameter clauses are specified for a single action, which
IPQoS does not allow.
| Combine all parameters for the action into a single parameters
clause.
|
Duplicate named action
| In the configuration file, two actions have the same name.
| Rename or remove one of the actions.
|
Duplicate named filter/class in action action-name
| Two filters or two classes have the same name in the same action, which is not allowed in the
IPQoS configuration file.
| Rename or remove one of the filters or classes.
|
Undefined class in filter filter-name in action action-name
| In the configuration file, the filter references a class that
is not defined in the action.
| Create the class, or change the filter reference to an already
existing class.
|
Undefined action in class class-name action action-name
| The class refers to an action that is not defined in the configuration
file.
| Create the action, or change the reference to an already existing
action.
|
Invalid parameters for action action-name
| In the configuration file, one of the parameters is invalid.
|
|
Mandatory parameter missing for action action-name
| A required parameter is not defined for an action in the configuration file.
|
|
Max number of classes reached in ipgpc
| More classes are specified than are allowed in the ipgpc action of the
IPQoS configuration file. The maximum number is 10007.
| Review the configuration file and remove unneeded classes. Alternatively, you can raise the
maximum number of classes by adding to the /etc/system file the entry
ipgpc_max_classes
class-number.
|
Max number of filters reached in action ipgpc
| More filters are specified than are allowed in the ipgpc action of the
IPQoS configuration file. The maximum number is 10007.
| Review the configuration file, and remove unneeded filters. Alternatively, you can raise the
maximum number of filters by adding the entry ipgpc_max_filters
filter-number to the /etc/system file.
|
Invalid/missing parameters for filter filter-name in action ipgpc
| In the configuration file, filter filter-name has
an invalid or missing parameter.
| Refer to the
ipqosconf
(1M)
man page for the list of valid parameters.
|
Name not allowed to start with '!', line line-number
| An action, filter, or class name begins with an exclamation mark (!), which is not allowed in
the IPQoS file.
| Remove the exclamation mark, or rename the action, class, or
filter.
|
Name exceeds the maximum name length line line-number
| An action, class, or filter name in the configuration file exceeds the maximum length of 23
characters.
| Assign a shorter name to the action, class, or filter.
|
Array declaration line line-number is invalid
| In the configuration file, the array declaration for the parameter
on line line-number is invalid.
|
|
Quoted string exceeds line, line-number
| The string does not have terminating quotation marks on the same line, which is required in
the configuration file.
| Make sure that the quoted string begins and ends on the same
line in the configuration file.
|
Invalid value, line line-number
| The value that is given on line-number of
the configuration file is not supported for the parameter.
|
|
Unrecognized value, line line-number
| The value on line-number of the configuration
file is not a supported enumeration value for its parameter.
|
|
Malformed value list line line-number
| The enumeration that is specified on line-number of
the configuration file does not conform to the specification syntax.
|
|
Duplicate parameter line line-number
| A duplicate parameter was specified on line-number,
which is not allowed in the configuration file.
| Remove one of the duplicate parameters.
|
Invalid action name line line-number
| The name of the action on line-number of the configuration file
uses the predefined name “continue” or “drop.”
| Rename the action so that the action does not use a predefined
name.
|
Failed to resolve src/dst host name for filter
at line line-number, ignoring filter
| ipqosconf could not resolve the source or
destination address that was defined for the given filter in the configuration
file. Therefore, the filter is ignored.
| If the filter is important, try applying the configuration at
a later time.
|
Incompatible address version line line-number
| The IP version of the address on line-number is
incompatible with the version of a previously specified IP address
or ip_version parameter.
| Change the two conflicting entries to be compatible.
|
Action at line line-number has the same name as currently installed
action, but is for a different module
| An action tried to change the module of an action that already exists in the system's IPQoS
configuration, which is not allowed.
| Flush the current configuration before you apply the new configuration.
|