| Sun Netra CP3250 Blade Server User’s Guide |     |
Sun Netra CP3250 Blade Server User’s Guide
820-5195-11
|
Contents |
1.4.2 Advanced Rear Transition Module
1.6.1 Required Hardware Components
1.6.2 Optional Hardware Components
1.7 Technical Support and Warranty
1.7.1 Locating the Part Number and Serial Number Information
1.7.2 Viewing the Electronic Blade Server ID Information
2. Hardware Installation and Service
2.1 Safety and Tool Requirements
2.1.1 Equipment and Operator Safety
2.1.2 Materials and Tools Required
2.2 Installing the Blade Server
2.2.1 Preparing for the Installation
2.2.1.1 Check Power, Thermal, Environmental, and Space Requirements
2.2.1.2 Local Network IP Addresses and Host Names Worksheet
2.2.1.3 Installation Procedure Summary
2.2.2 Configuring the Hardware
2.2.2.1 Verify Chassis Fan Tray Upgrade
2.2.2.2 Installing Optional Components
2.2.2.3 Configuring the Advanced Rear Transition Module (ARTM)
2.2.3 Installing the Netra CP3250 Blade Server in an ATCA Shelf
2.2.3.1 Installing an Advanced Rear Transition Module (ARTM)
2.2.3.2 Installing the Blade Server Into the Shelf
2.2.4 Connecting External I/O Cables
2.2.4.1 Connecting Cables to a System Console Running the Solaris OS
2.2.4.2 Connecting Cables to the System Console Not Running the Solaris OS
2.2.4.3 Netinstall Boot Device Map
2.3.1 Hot-Swapping the Netra CP3250 Blade Server
2.3.2 Powering Off the Netra CP3250 Blade Server
2.3.3 Removing the Netra CP3250 Blade Server
2.3.5 Automatic Power-Off Events
2.3.6.2 Installing a DDR2 DIMM
2.3.7 Installing the Optional Compact Flash Card
2.3.9 Adding or Replacing the Battery
2.3.10 Changing Jumper Settings
2.3.10.1 Clearing the CMOS Setting Using Jumper 2
2.3.10.2 Changing the OOS LED Color Using Jumper 13
2.3.11 Checking DIP Switch Settings
2.3.12 Resetting the Netra CP3250 Blade Server
3.5.5 Trusted Platform Module (TPM)
3.5.8 Broadcom 5715C Gigabit Ethernet
3.5.9 Sun Dual 10-Gbit Ethernet/Quad 1-Gbit RGMII Network Interface Chip
3.6.2 EIDE/ATA for Compact Flash
4.4 Configuring Sun Netra CP3250 blade server For 1 GbE or 10 GbE Switches
5. Configuring and Using BIOS Firmware
5.1.3 Description of the BIOS Screens
5.2 Changing the Configuration of a BIOS Menu Item
5.3 Setting the Boot Device Using BIOS Setup Screens
5.4 Setting Supervisor and User Passwords
5.5 Resetting the System Time and System Date
5.8 Perform a Live Firmware Upgrade
B.3.3 Power Connector (Zone 1)
B.3.4 Data Transport Connector (Zone 2)
B.3.5 Advanced Rear Transition Module (ARTM) Connector (Zone 3)
B.3.5.1 Zone 3 (J30) Connector Pin Assignments
B.3.5.2 Zone 3 (J31) Connector PIN Assignments
B.3.5.3 Zone 3 (J32) Connector PIN Assignments
B.3.5.4 Zone 3 (J33) Connector PIN Assignments
B.3.5.5 Zone 3 Signal Descriptions
C.1 Shelf Manager Command-Line Interface
C.2 Shelf Manager CLI Commands
| Sun Netra CP3250 Blade Server User’s Guide | 820-5195-11 | |
Copyright © 2009 Sun Microsystems, Inc. All rights reserved.