Figures

FIGURE 1-1 Sun StorEdge S1 Array

FIGURE 1-2 SCSI-3 and VHDCI Connectors

FIGURE 1-3 Front of Sun StorEdge S1 Array With Bezel

FIGURE 1-4 Front of Sun StorEdge S1 Array With Bezel Removed

FIGURE 1-5 Releasing the Left Retaining Lug to Release the Nameplate's Left Side

FIGURE 1-6 Pulling the Right Retaining Lug Away From the Bezel

FIGURE 1-7 Removing the Front Bezel

FIGURE 1-8 Sun StorEdge S1 Array, Back View

FIGURE 1-9 Power Switch

FIGURE 1-10 SCSI ID Switch

FIGURE 1-11 Back Panel LEDs

FIGURE 1-12 AC Power Connector on the Back of an AC Array

FIGURE 1-13 DC Power Connectors on the Back of a DC Array

FIGURE 1-14 Airflow Requirements (Front and Back)

FIGURE 1-15 Airflow Requirements (Open Rack)

FIGURE 1-16 Airflow Requirements (Closed Rack)

FIGURE 1-17 Disk Drives in the Sun StorEdge S1 Array

FIGURE 2-1 DC Connector

FIGURE 2-2 Strain Relief Housing

FIGURE 2-3 Cage Clamp Lever

FIGURE 2-4 Power Connector On the Array

FIGURE 2-6 Stripping the Insulation From the Wire

FIGURE 2-7 Opening the DC Connector Cage Clamp Using the Cage Clamp Lever

FIGURE 2-8 Opening the DC Connector Cage Clamp Using a Screwdriver

FIGURE 2-9 Inserting Wires by Color Into the DC Connector

FIGURE 2-11 Routing the Wires out of the Bottom Portion of the Strain Relief Housing

FIGURE 3-1 Attaching the Side Mount Brackets to the Array

FIGURE 3-2 Assembling an Adjustable Bracket for a Sun 72-inch Expansion Cabinet or Sun Fire Expansion Cabinet

FIGURE 3-3 Assembling an Adjustable Bracket for a Sun Rack 900 or Standard 19-inch Rack or Cabinet

FIGURE 3-4 Attaching the Stud Plate

FIGURE 3-6 Fastening the Brackets in Sun StorEdge 72-inch Expansion Rack or Cabinet - Front and Back View (Side Panels Removed for Clarity)

FIGURE 3-7 Fastening the Brackets to the Sun Rack 900 or Standard 19-inch Rack or Cabinet

FIGURE 3-9 Adjusting the Mount and Tightening the Thumbscrew

FIGURE 3-10 Cable Management Bracket

FIGURE 3-12 Attaching Brackets Towards the Front of an Array (for Two-Post Rack Install)

FIGURE 3-13 Attaching Brackets Towards the Back of an Array (for Two-Post Rack Install)

FIGURE 3-14 Front Mounting the Array in a Two-Post Rack

FIGURE 3-15 Back-Mounting the Array Into a Two-Post Relay Rack With Brackets at Back

FIGURE 3-16 Example of SCSI ID Drive Assignment Sequence

FIGURE 3-18 Four Sun StorEdge S1 Arrays on a Host System With LVD SCSI (Example)

FIGURE 3-19 One Sun StorEdge S1 Array and One Netra st D130 Storage Array on a Host System With LVD SCSI (Example)

FIGURE 3-20 SCSI ID Switch on the Back of the Array (AC Version)

FIGURE 3-21 SCSI IN and OUT Ports on the Back of the Array (AC Version)

FIGURE 3-22 Daisy Chaining an Array With a Narrow SCSI Device

FIGURE 3-23 Power Connector for the AC Power Cable

FIGURE 3-24 DC Grounding Lug Nuts for Connecting the DC Grounding Cable

FIGURE 3-26 DC Connectors on the Left Back of the Array

FIGURE 3-28 Locating the Chassis Ground Connection Screws

FIGURE 3-29 Securing the Chassis Ground Connection Screw

FIGURE 4-1 Adding a Disk Drive

FIGURE 4-2 Removing and Replacing a Disk Drive

FIGURE 5-1 Front Panel LEDs With Bezel

FIGURE 5-2 Front Panel LEDs With Bezel Removed

FIGURE 5-3 Checking the Binary SCSI LEDs

FIGURE 5-4 Back Panel LEDs

FIGURE 5-5 Autotermination Indication LEDs in an UltraSCSI or Wide SCSI Daisy Chain

FIGURE 5-6 Autotermination Indication LEDs in a Narrow SCSI Daisy Chain

FIGURE 5-7 Pulling a Tether Until It Stops

FIGURE 5-8 Pushing the Tether to One Side Until it Head Emerges

FIGURE 5-9 Pushing the Tether in the Opposite Direction

FIGURE 5-10 Pulling the Head of the Tether out of the Array

FIGURE 5-11 Cleaning the Front Bezel Screen

FIGURE 5-12 Cleaning the Back Fan Screens