When setting up serial port information, start Admintool, and select Serial Ports from the Browse menu. Select a serial port from the Serial Ports window and then choose Modify from the Edit menu to bring up the Modify Serial Port window. This window provides access to the port templates and provides information on the port in three levels of detail--Basic, More, and Expert.
The Modify Serial Port window appears in the Basic detail mode. To view More or Expert details, select the More or Expert option from the Detail menu.
The descriptions of each item in the Modify Serial window are listed in the table below.
Table 13-1 Modify Serial Port Window Items
Detail |
Item |
Description |
---|---|---|
Basic |
Port |
Lists the port or ports you selected from Serial Ports main window. |
|
Service |
Specifies that the service for the port is turned on (enabled). |
|
Baud Rate |
Specifies the line speed used to communicate with the terminal. The line speed represents an entry in the /etc/ttydefs file. |
|
Terminal Type |
Shows the abbreviation for the type of terminal, for example, ansi or vt100. Similar abbreviations are found in /etc/termcap. This value is set in the $TERM environment variable. |
More |
Option: Initialize Only |
Specifies that the port software is initialized but not configured. |
|
Option: Bidirectional |
Specifies that the port line is used in both directions. |
|
Option: Software Carrier |
Specifies that the software carrier detection feature is used. If the option is not checked, the hardware carrier detection signal is used. |
|
Login Prompt |
Shows the prompt displayed to a user after a connection is made. |
|
Comment |
Shows the comment field for the service. |
|
Service Tag |
Lists the service tag associated with this port--typically an entry in the /dev/term directory. |
|
Port Monitor Tag |
Specifies the name of the port monitor to be used for this port. Note: The default monitor is typically correct. |
Expert |
Create utmpx Entry |
Specifies that a utmpx entry is created in the accounting files upon login. Note: This item must be selected if a login service is used. See the Service item. |
|
Connect on Carrier |
Specifies that a port's associated service is invoked immediately when a connect indication is received. |
|
Service |
Shows the program that is run upon connection. |
|
Streams Modules |
Shows the STREAMS modules that are pushed before the service is invoked. |
|
Timeout (secs) |
Specifies the number of seconds before a port is closed if the open process on the port succeeds and no input data is received. |
The table below describes the menu items (and their default values) when setting up a terminal using Serial Ports.
Table 13-2 Terminal - Hardwired Default Values
Detail |
Item |
Default Value |
---|---|---|
Basic |
Port |
-- |
|
Service |
Enabled |
|
Baud Rate |
9600 |
|
Terminal Type |
-- |
More |
Option: Initialize Only |
no |
|
Option: Bidirectional |
no |
|
Option: Software Carrier |
yes |
|
Login Prompt |
login: |
Comment |
Terminal - Hardwired |
|
|
Service Tag |
-- |
|
Port Monitor Tag |
zsmon |
Expert |
Create utmpx Entry |
yes |
|
Connect on Carrier |
no |
|
Service |
/usr/bin/login |
|
Streams Modules |
ldterm,ttcompat |
|
Timeout (secs) |
Never |
The table below describes the three modem templates available when setting up a modem using Serial Ports.
Table 13-3 Modem Templates
Modem Configuration |
Description |
---|---|
Dial-In Only |
Users can dial in to the modem but cannot dial out. |
Dial-Out Only |
Users can dial out from the modem but cannot dial in. |
Bidirectional |
Users can either dial in or out from the modem. |
The table below describes the default values of each template.
Table 13-4 Modem Template Default Values
Detail |
Item |
Modem - Dial-In Only |
Modem - Dial-Out Only |
Modem - Bidirectional |
---|---|---|---|---|
Basic |
Port |
-- |
-- |
-- |
|
Service |
Enabled |
Enabled |
Enabled |
|
Baud Rate |
9600 |
9600 |
9600 |
|
Terminal Type |
-- |
-- |
-- |
More |
Option: Initialize Only |
yes |
no |
no |
|
Option: Bidirectional |
no |
no |
yes |
|
Option: Software Carrier |
no |
no |
no |
|
Login Prompt |
login: |
login: |
login: |
|
Comment |
Modem - Dial-In Only |
Modem - Dial-Out Only |
Modem - Bidirectional |
|
Service Tag |
-- |
-- |
-- |
|
Port Monitor Tag |
zsmon |
zsmon |
zsmon |
Expert |
Create utmpx Entry |
yes |
yes |
yes |
|
Connect on Carrier |
no |
no |
no |
|
Service |
/usr/bin/login |
/usr/bin/login |
/usr/sbin/login |
|
Streams Modules |
ldterm,ttcompat |
ldterm,ttcompat |
ldterm,ttcompat |
|
Timeout (secs) |
Never |
Never |
Never |
The table below describes the default values for the Initialize Only template.
Table 13-5 Initialize Only - No Connection Default Values
Detail |
Item |
Default Value |
---|---|---|
Basic |
Port |
-- |
|
Service |
Enabled |
|
Baud Rate |
9600 |
|
Terminal Type |
-- |
More |
Option: Initialize Only |
yes |
|
Option: Bidirectional |
no |
|
Option: Software Carrier |
no |
|
Login Prompt |
login: |
|
Comment |
Initialize Only - No Connection |
|
Service Tag |
-- |
|
Port Monitor Tag |
zsmon |
Expert |
Create utmpx Entry |
yes |
|
Connect on Carrier |
no |
|
Service | /usr/bin/login |
|
Streams Modules |
ldterm,ttcompat |
|
Timeout (secs) |
Never |
Verify that the following prerequisites are met. To use Admintool, you must:
Have a bit-mapped display monitor. The Admintool software can be used only on a system with a console that is a bit-mapped screen such as a standard display monitor that comes with a Sun workstation.
Be running an X Window System, such as the CDE environment.
Be a member of the sysadmin group (group 14).
If you want to perform administration tasks on a system with an ASCII terminal as the console, use Solaris commands instead.
Start Admintool.
$ admintool & |
The Users main window is displayed.
Start Admintool, if it's not already running.
See "How to Start Admintool" for more information on starting Admintool.
Select Serial Ports from the Browse menu.
The Serial Ports menu is displayed.
Select the port or ports that will be used with a terminal.
Choose Modify from the Edit menu.
The Modify Serial Port window appears in the Basic Detail mode. To enter additional details, select either the More or Expert Detail modes.
Choose Terminal-Hardwired from the Use Template menu.
See Table 13-2 for a description of the Terminal-Hardware menu items.
Change values of template entries if desired.
Click on OK to configure the port.
Use the pmadm command to verify the terminal service has been added.
$ pmadm -l -s ttya |
Start Admintool, if it's not already running.
See "How to Start Admintool" for more information on starting Admintool.
Select Serial Ports from the Browse menu.
The Serial Ports menu is displayed.
Select the port or ports that will be used with a modem.
Choose Modify from the Edit menu.
The Modify Serial Port window appears in the Basic Detail mode. To enter additional details, select either the More or Expert Detail modes.
Choose the modem configuration template from the Use Template menu that meets or most closely matches your modem service.
See Table 13-3 for a description of each template.
See Table 13-4 for the default values of each template. If a UUCP service will be used to dial in to your modem on a Solaris system, see "How to Set Up a Modem for Use With UUCP" for the rest of the procedure.
Change values of template entries if desired.
Click on OK to configure the port.
Use the pmadm command to verify the modem service has been configured for use with UUCP.
$ pmadm -l -s ttyb |
UUCP sends information to a service using seven bits and even parity. Solaris modem configurations use eight bits and no parity for internationalization purposes. To set up your modem service to work with UUCP, follow these instructions.
Start Admintool, if it's not already running.
See "How to Start Admintool" for more information on starting Admintool.
Select Serial Ports from the Browse menu.
The Serial Ports menu is displayed.
Select the port or ports that will be used with a modem.
Choose Modify from the Edit menu.
The Modify Serial Port window appears in the Basic Detail mode. For additional details, select either the More or Expert Detail modes.
Select Other from the Baud Rate menu.
A window listing baud rates from the /etc/ttydefs file is displayed.
Enter a baud rate that provides seven bit, even parity service. Click on OK.
Change values of other template entries if desired.
Click on OK to configure the port.
Use the pmadm command to verify the modem service has been configured for use with UUCP.
$ pmadm -l -s ttya |
In this example, the 9600E baud rate was selected. This provides a service with a 9600 baud rate, seven bits, and even parity.
Start Admintool, if it's not already running.
See "How to Start Admintool" for more information on starting Admintool.
Select Serial Ports from the Browse menu.
The Serial Ports menu is displayed.
Select the port or ports that you want to initialize.
Choose Modify from the Edit menu.
The Modify Serial Port window appears in the Basic Detail mode. To enter additional details, select either the More or Expert Detail modes.
Choose Initialize Only - No Connection from the Use Template menu.
See Table 13-5 for a description of the Initialize Only - No Connection template.
Click on OK to initialize the port.
Use the pmadm command to verify the port has been disabled.
$ pmadm -l -s ttyb |
Start Admintool, if it's not already running.
See "How to Start Admintool" for more information on starting Admintool.
Select Serial Ports from the Browse menu.
The Serial Ports menu is displayed.
Select the port or ports that you want to disable.
Choose Modify from the Edit menu.
Click on the Service Enable button to disable the port service in the Modify window.
This button acts as a toggle switch to enable or disable a port service.
Click on OK to disable the port.
Use the pmadm command to verify the port service has been disabled.
$ pmadm -l -s ttya |
Start Admintool, if it's not already running.
See "How to Start Admintool" for more information on starting Admintool.
Select the port or ports that has a service you want to delete.
Choose Delete from the Edit menu.
You are asked if you really want to delete the service for the specified port or ports. You can cancel the delete operation or continue with it.
Use the pmadm command to verify the port service has been deleted.
$ pmadm -l -s ttya |