| Sun Netra CP3060 Blade Server User’s Guide |     |
Sun Netra CP3060 Blade Server User’s Guide
819-4967-11
|
Contents |
1. Introduction to the Sun Netra CP3060 Blade Server
1.1 Overview of the Sun Netra CP3060 Blade Server
1.2 Features of the Sun Netra CP3060 Blade Server
1.3 Sun Netra CP3060 Blade Server System Configurations
1.6 Technical Support and Warranty
1.6.1 Blade Server Part Number, Serial Number, and Revision Number Identification
2.1 Equipment and Operator Safety
2.2 Materials and Tools Required
2.3 Preparing for the Installation
2.3.1 Checking Power, Thermal, Environmental, and Space Requirements
2.3.2 Determining Local Network IP Addresses and Host Names
2.3.3 Installation Procedure Summary
2.4 Configuring the Blade Server Hardware
2.4.1 Installation of DDR-2 DIMM Memory Modules
2.4.1.1 Installing a DDR-2 DIMM Memory Module
2.4.1.2 Removing a DDR-2 DIMM Memory Module
2.4.2 Installation of Optional Compact Flash Card
2.4.3 Configuring Rear Transition Module Hardware
2.5 Installing the Sun Netra CP3060 Blade Server
2.5.1 Installing the Sun Netra CP3060 Blade Server With a Rear Transition Module
2.5.1.1 Installing a Rear Transition Module
2.5.2 Installing the Sun Netra CP3060 Blade Server
2.6 Connecting External I/O Cables
2.7 Installation of Optional AMC Modules
2.7.0.1 Installing an Optional AMC Module
3.1 Operating Systems and Patches
3.3 Mandatory /etc/system File Entry
To Check and Create the Mandatory /etc/system File Entry
3.4 Installing Diskless Clients
3.4.1 Creating a Boot Server for Diskless Clients
3.4.2 Adding a Diskless Client
3.5 Downloading and Installing SunVTS Software
4. Firmware and Blade Server Management
4.2 Power-On Self-Test Diagnostics
4.2.2 POST Diagnostic and Error Message Format
4.3.1 Getting to the ok Prompt
4.3.3.3 Checking Network Using watch-net and watch-net-all Commands
4.3.4 OpenBoot Configuration Variables
4.3.4.1 Viewing and Setting OpenBoot Configuration Variables
4.5.1 Enabling and Disabling Automatic System Recovery
4.5.1.1 To Enable Automatic System Recovery
4.5.1.2 To Disable Automatic System Recovery
4.6.1 Hot-Swapping the Sun Netra CP3060 Blade Server
4.8 Retrieving Device Information
4.9 Mandatory /etc/system File Entry
To Check and Create the Mandatory /etc/system File Entry
5. Hardware and Functional Descriptions
5.1.1.6 UltraSPARC T1 RAS Features
5.1.1.7 UltraSPARC T1 Processor Speed
5.1.2.2 Memory Subsystem RAS Features
5.1.2.3 Serial Presence Detect
5.1.4.3 PCI-E to Dual GbE Controller
5.1.5 Service Processor MPC885
5.1.5.1 MPC Bus External Devices
5.1.5.2 Field-Programmable Gate Array
5.1.6 Intelligent Platform Management Controller
5.1.6.1 Intelligent Platform Management Bus
5.1.6.7 Extended Interface E-keying Control
5.1.6.9 I2C Device Address Map
5.1.6.10 System Monitor and Thresholds
5.3.3 ATCA Power Module (-48V to 12V)
5.3.4 On-Board DC/DC Regulators
A.4.4 Midplane Power Connector (Zone 1)
A.4.5 Data Transport Connector (Zone 2)
A.4.7 TOD Clock Battery Holder
| Sun Netra CP3060 Blade Server User’s Guide | 819-4967-11 | |
Copyright © 2009 Sun Microsystems, Inc. All rights reserved.