| Skip Navigation Links | |
| Exit Print View | |
|
Netra SPARC T5-1B Server Module HTML Document Collection |
Understanding System Administration Resources
Oracle VM Server for SPARC Overview
Multipathing Software Overview
Oracle Hardware Management Pack Overview
Oracle Enterprise Manager Ops Center Overview
Obtain the OpenBoot Prompt Under Various Conditions
Display the Oracle ILOM Prompt
Redirect the System Console to a Local Graphics Monitor
Powering the Server On and Off
Power On the Server (Oracle ILOM CLI)
Power Off the Server (Oracle ILOM CLI)
Power On the Server (Oracle ILOM Web Interface)
Power Off the Server (Oracle ILOM Web Interface)
Power On a Server With Multiple Active Domains (Oracle VM Server for SPARC)
Power Off a Server With Multiple Active Domains (Oracle VM Server for SPARC)
Reset the Server (Oracle Solaris)
Reset the Server (Oracle ILOM)
Booting and Shutting Down the OS
Booting and Shutting Down Oracle Solaris
Boot the OS Manually (OpenBoot)
Shut Down the OS (init Command)
Shut Down the OS (shutdown Command)
Obtain the OpenBoot Prompt (Oracle Solaris)
Obtain the OpenBoot Prompt (Oracle ILOM CLI)
Obtain the OpenBoot Prompt (Oracle ILOM Web Interface)
Configuring Boot and Restart Behavior
Change the Default Boot Device (OpenBoot)
Enable or Disable Automatic Booting (OpenBoot)
Enable or Disable Automatic Booting (Oracle Solaris)
OpenBoot Configuration Parameters
Boot Mode Overview (Oracle ILOM)
Configure the Host Boot Mode (Oracle VM Server for SPARC)
Change the Host Boot Mode Behavior at Reset (Oracle ILOM)
Manage the Host Boot Mode Script (Oracle ILOM)
Display the Host Boot Mode Expiration Date (Oracle ILOM)
Override OpenBoot Settings to Reset the Server
Server Restart Behavior Configuration (Oracle ILOM)
Changing Server Identification Information
Change Customer Data on FRU PROMs
Change Server Identifier Information
Restore the Host Power State at Restart
Specify the Host Power State at Restart
Disable or Reenable the Host Power-On Delay
Specify Parallel Boot of the SP and Host
Specify Host Virtual Keyswitch Behavior
Reset the Values in the SP to Default Values
Configuring SP and Host Network Addresses
Disable or Reenable Network Access to the SP
Display the SP Network Parameters
Connecting to the SP (In-band)
Oracle ILOM In-band (Sideband) Management
Configure SP In-band (Sideband) Access
Matching Devices to Device Names
Importance of Matching a Physical Device to a Name
Display Server Components (Oracle ILOM)
Locate Device Paths (OpenBoot)
Correlate WWN Device Names With Physical Locations (diskinfo Command)
probe-scsi-all Device Naming (OpenBoot)
Correlate WWN Device Names With Physical Locations (probe-scsi-all Command)
Identify a Disk Slot (Oracle Solaris)
WWN Syntax in an Oracle Solaris 10 Installation on an Individual Drive
WWN Syntax in an Oracle Solaris 10 Installation on a RAID Volume
RAID Capabilities in Oracle Enterprise Manager Ops Center
FCode-Based RAID Utility Commands
Prepare to Create a RAID Hardware Volume (FCode-based RAID Utility)
Hot-Spare Drives in RAID Volumes (LSI)
Determining if a Drive Has Failed
Locate Error Messages Related to Drives in a RAID Volume
Display Status (FCode-Based RAID Utility)
Display Status (sas2ircu Utility, LSI)
RAID Drive Replacement Strategies
Oracle ILOM is system management firmware that is preinstalled on most SPARC servers. Oracle ILOM enables you to actively manage and monitor components installed in the server. Oracle ILOM provides a browser-based interface and a CLI, as well as SNMP and IPMI interfaces.
In the server's SP, Oracle ILOM runs independently of the server host and regardless of the server power state as long as AC power is connected to the server (or to the modular system that contains the server module). When you connect the server to AC power, the SP immediately starts up and begins monitoring the server. All environmental monitoring and control are handled by Oracle ILOM.
The -> prompt indicates that you are interacting with the Oracle ILOM SP directly. This prompt is the first prompt you see when you log in to the server through the SER MGT port or NET MGT port, regardless of the host's power state. On a modular system, that prompt is also present when you log in to a server module either directly or through Oracle ILOM on the CMM of the modular system.
You can also access the Oracle ILOM prompt (->) from the OpenBoot ok prompt.
The SP supports concurrent Oracle ILOM sessions per server. Multiple SSH or web connections are available through the NET MGT port, and one connection is available through the SER MGT port.
For more information about how to work with Oracle ILOM features that are common to all platforms managed by Oracle ILOM, see the Oracle ILOM documentation at:
http://www.oracle.com/goto/ILOM/docs
Oracle ILOM operates on many platforms, supporting features that are common to all platforms. Some Oracle ILOM features belong to only a subset of platforms. For example, CMM features only apply to server modules, such as the SPARC and Netra SPARC T5-1B server modules.
To perform some procedures documented in the Oracle ILOM base documentation, you must create a serial connection to the server and activate the Physical Presence switch on the server. For information about creating a serial connection, see the installation guide for the server.
|