Index R - Administering TCP/IP Networks, IPMP, and IP Tunnels in Oracle® Solaris 11.2

oracle home

Administering TCP/IP Networks, IPMP, and IP Tunnels in Oracle^® Solaris 11.2

Exit Print View

Search Term

Search Scope:

This Document Entire Library

Administering TCP/IP Networks, IPMP, and IP Tunnels in Oracle^® Solaris 11.2

Document Information

Using This Documentation

Product Documentation Library

Access to Oracle Support

Feedback

Chapter 1 Administering TCP/IP Networks

Customizing TCP/IP Properties

Enabling Packet Forwarding Globally

Administering Default Address Selection

Description of the /etc/inet/ipaddrsel.conf Configuration File

Description of the ipaddrsel Command

Reasons to Modify the IPv6 Address Selection Policy Table

How to Administer the IPv6 Address Selection Policy Table

How to Modify the IPv6 Address Selection Table for the Current Session Only

Administering Transport Layer Services

Setting Up a Privileged Port

Implementing Traffic Congestion Control

Logging IP Addresses of All Incoming TCP Connections

Adding Services That Use the SCTP Protocol

How to Add Services That Use the SCTP Protocol

Configuring TCP Wrappers

How to Use TCP Wrappers to Control Access to TCP Services

Changing the TCP Receive Buffer Size

Monitoring Network Status With the netstat Command

Filtering netstat Output by Address Type

Displaying the Status of Sockets

Displaying Statistics by Protocol

Displaying Network Interface Status

Displaying User and Process Information

Displaying the Status of Known Routes

Displaying Additional Network Status With the netstat Command

Performing TCP and UDP Administration With the netcat Utility

Administering and Logging Network Status Displays

How to Control the Display Output of IP-Related Commands

Logging Actions of the IPv4 Routing Daemon

How to Trace the Activities of the IPv6 Neighbor Discovery Daemon

Probing Remote Hosts With the ping Command

ping Command Modifications for IPv6 Support

Determining if a Remote Host Is Reachable

Determining if Packets Between Your Host and a Remote Host Are Being Dropped

Displaying Routing Information With the traceroute Command

traceroute Command Modifications for IPv6 Support

Discovering the Route to a Remote Host

Tracing All Routes

Analyzing Network Traffic With the TShark and Wireshark Analysers

Monitoring Packet Transfers With the snoop Command

snoop Command Modifications for IPv6 Support

How to Check Packets From All Interfaces

How to Check Packets From an IPMP Group

How to Capture snoop Output to a File

How to Check Packets Between an IPv4 Server and a Client

Monitoring IPv6 Network Traffic

Monitoring Packets by Using IP Layer Devices

How to Check Packets on the IP Layer

Methods for Checking Packets

Observing Network Traffic With the ipstat and tcpstat Commands

Chapter 2 About IPMP Administration

What's New in IPMP

IPMP Configuration Changes

IPMP Support in Oracle Solaris

Benefits of Using IPMP

Rules for Using IPMP

IPMP Components

Types of IPMP Interface Configurations

Failure Detection in IPMP

Probe-Based Failure Detection

Probe-Based Failure Detection Using Test Addresses

Probe-Based Failure Detection Without Using Test Addresses

Group Failure

Link-Based Failure Detection

Failure Detection and the Anonymous Group Feature

Detecting Physical Interface Repairs

FAILBACK=no Mode

IPMP and Dynamic Reconfiguration

Chapter 3 Administering IPMP

Configuring IPMP Groups

How to Plan an IPMP Group

How to Configure an IPMP Group That Uses DHCP

How to Configure an Active-Active IPMP Group

How to Configure an Active-Standby IPMP Group

Maintaining Routing While Deploying IPMP

How to Preserve the Default Route While Using IPMP

Administering IPMP

How to Add an Interface to an IPMP Group

How to Remove an Interface From an IPMP Group

How to Add IP Addresses to an IPMP Group

How to Delete IP Addresses From an IPMP Interface

How to Move an Interface From One IPMP Group to Another IPMP Group

How to Delete an IPMP Group

Configuring Probe-Based Failure Detection

About Probe-Based Failure Detection

Requirements for Choosing Targets for Probe-based Failure Detection

Selecting a Failure Detection Method

How to Manually Specify Target Systems for Probe-Based Failure Detection

How to Configure the Behavior of the IPMP Daemon

Monitoring IPMP Information

Customizing the Output of the ipmpstat Command

Using the ipmpstat Command in Scripts

Chapter 4 About IP Tunnel Administration

What's New in IP Tunnel Administration

IP Tunnel Feature Summary

Types of Tunnels

Tunnels in the Combined IPv6 and IPv4 Network Environments

6to4 Tunnels

Topology of a 6to4 Tunnel

6to4relay Command

Packet Flow Through the 6to4 Tunnel

Considerations for Enabling Tunnels to a 6to4 Relay Router

Packet Flow Between a 6to4 Site and a Native IPv6 Site

About Deploying IP Tunnels

Requirements for Creating IP Tunnels

Requirements for IP Tunnels and IP Interfaces

Chapter 5 Administering IP Tunnels

IP Tunnel Administration in Oracle Solaris

Administering IP Tunnels

How to Create and Configure an IP Tunnel

How to Configure a 6to4 Tunnel

How to Enable a 6to4 Tunnel to a 6to4 Relay Router

Modifying an IP Tunnel Configuration

Displaying an IP Tunnel's Configuration

Displaying an IP Tunnel's Properties

How to Delete an IP Tunnel

Index

Index Numbers and Symbols

Language:

R

Reconfiguration Coordination Manager (RCM) framework index icon

IPMP and Dynamic Reconfiguration

relay router, 6to4 tunnel configuration

How to Enable a 6to4 Tunnel to a 6to4 Relay Router

repair detection time index icon

Detecting Physical Interface Repairs

route command

–inet6 option index icon

About Probe-Based Failure Detection

routers

role, in 6to4 topology index icon

Topology of a 6to4 Tunnel

routing and IPMP index icon

Maintaining Routing While Deploying IPMP

routing tables

tracing all routes index icon

Tracing All Routes