Usable capacity 3.2 TB

Max LBA: 6,251,233,968

Max. LBA shown represents the total user addressable sectors in LBA mode and calculated by IDEMA rule.

PCIe Gen3 half-height, half-width, single-slot x8 connector

PCIe interface that complies with the PCI Express Specification 3.0

PCI low-profile MD2 specification

Add-in Card (AIC) Form Factor

Single slot x8 connector

Half-height, half-width, half-length, low-profile PCIe 3.0 board

V2 128Gb NAND Flash Memory

V2_TLC HDP 16Landing (533Mbps)

NVM Express (NVMe)

PCI Express Gen3 - Single port x8 lanes

Enhanced Power-Loss Data Protection

LDPC and XOR Engine ECC

End-to-End Data Protection

Up to 128 I/O Queues per Port

Deallocate (TRIM) Command

PCI Express AER (Advanced Error Reporting)

129 vectors for MSI-X Support

SSD Enhanced S.M.A.R.T. Feature Set

Hardware based AES-XTS 256-bit Encryption Engine

Static and Dynamic Wear Leveling

Half-height, half-length

Interface: PCI Express Gen3 x8

Bytes per Sector: 512, 520, 4096, 4160 Bytes

Data Transfer Rate: (128KB data size)

Sequential performance was measured by using FIO in Ubuntu with queue depth 32 by 16 workloads. Actual performance may vary depending on use conditions and environment.

• Sequential Read Up to 5,500 MB/s

• Sequential Write Up to 1,800 MB/s

Data I/O Speed:

Random performance was measured by using FIO in Ubuntu with queue depth 32 by 16 workloads. Measurements were performed on a full Logical Block Address (LBA) span of the drive in sustained state. Actual performance may vary depending on use conditions and environment.

• Random Read Up to 750K IOPS

  The read latency is measured by using FIO in Ubuntu and 4KB transfer size with queue depth 1 on a random workload of sustained state.

• Random Write Up to 120K IOPS

  The write latency is measured by using FIO in Ubuntu and 4KB transfer size with queue depth 1 on a sequential workload of sustained state.

Latency: (Sustained random workload)

Typical values.

• Random Read (typical): 90 μsec

  The random read/write latency is measured by using FIO in Ubuntu and 4KB transfer size with queue depth 1 on a random workload of sustained state.

• Write (typical): 20 μsec

  The sequential read/write latency is measured by using FIO in Ubuntu and 4KB transfer size with queue depth 1 on a sequential workload of sustained state.

• Drive Ready Time (typical): 2 sec

  The maximum taking time to be ready for receiving commands after power-up (CSTS.Ready=1). It is expected that I/O commands may not be completed at this point.

Quality of service (QoS) - Read/Write (99%) 95/60 μsec

Performance Consistency - Read/Write (99.9%) Up to 98/94%

PCI Express Base Specification Rev. 3.0

NVM Express Specification Rev. 1.1b

Enterprise SSD Form Factor Ver. 1.0a

Uncorrectable Bit Error Rate 1 sector per 10¹⁷ bits read

MTBF: 2,000,000 hours

Power on Cycles (Ambient): 20,000

Component Design Life: 5 years

Endurance: 5 DWPD

PBW (@4KB Random Write): 29.2 PB

Data Retention: 3 months

Temperature, Case (Tc⁵)

Tc is measured at the hottest point on the case with the airflow condition of more than 2.5CFM at 25℃ of ambient temperature.

• Operating 0 ~ 55° C

• Non-operating -45 ~ 85° C

  Storing (or shipping) without power connection.

Humidity (Non-operating) 5 ~ 95%

Shock 1,500 G / 0.5msec

Vibration - Sinusoidal 20 Gpeak, 10 ~ 2000Hz

Supply Voltage / Tolerance: 12V∓10%

Active (max. RMS): 25 W

Active power is measured using IOMeter2006.

Idle (typ.): 7 W

Width: 69.85 +/-0.25 mm

Length: 167.65 +/-0.25 mm

Height: 18.71 +/-0.20 mm

Weight: Up to 330 g

Oracle Solaris 11.3 (SRU 2)

Oracle Linux 6.7, based on UEK4 (Unbreakable Linux Kernel Release 4)

Oracle Linux 7.1, based on UEK4 (Unbreakable Linux Kernel Release 4)

Oracle VM 3.3.3/3.4.1