관리 인터페이스 구성(CLI)

언어:

다음 절차에 따라 관리 인터페이스를 구성합니다.

configuration net으로 이동한 후 datalinks를 입력합니다.

hostname:> configuration net
hostname:configuration net> datalinks

show를 입력하여 데이터 링크를 봅니다.

hostname:configuration net datalinks> show
Datalinks:

DATALINK        CLASS        LINKS        STATE        ID        LABEL
igb0            device       igb0         up           -         Untitled Datalink

vnic 컨텍스트로 이동하고 해당 레이블을 설정해서 링크를 관리 링크로 표시하여 관리 데이터 링크에 대해 VNIC를 만들고, 선택적으로 VLAN ID를 지정합니다. commit을 입력한 후 cd ..를 입력하여 다음 단계를 위한 올바른 컨텍스트로 돌아갑니다.

hostname:configuration net datalinks> vnic
hostname:configuration net datalinks vnic (uncommitted)> set links=igb0
                          links = igb0 (uncommitted)
hostname:configuration net datalinks vnic (uncommitted)> set label=management-datalink-1
                          label = management-datalink-1 (uncommitted)
hostname:configuration net datalinks vnic (uncommitted)> commit
hostname:configuration net datalinks vnic> cd ..

VLAN ID를 지정하려면 다음과 같이 하십시오.

hostname:configuration net datalinks vnic> set id=100
                              id = 100 (uncommitted)
hostname:configuration net datalinks vnic (uncommitted)> commit
hostname:configuration net datalinks vnic> cd ..

클러스터형 컨트롤러인 경우 vnic 컨텍스트로 이동하고 고유 레이블을 설정하여 두번째 관리 데이터 링크에 대해 VNIC를 만들고, 선택적으로 VLAN ID를 지정합니다. commit을 입력한 후 cd ..를 입력하여 다음 단계를 위한 올바른 컨텍스트로 돌아갑니다.

hostname:configuration net datalinks> vnic
hostname:configuration net datalinks vnic (uncommitted)> set links=igb0
                          links = igb0 (uncommitted)
hostname:configuration net datalinks vnic (uncommitted)> set label=management-datalink-2
                          label = management-datalink-2 (uncommitted)
hostname:configuration net datalinks vnic (uncommitted)> commit
hostname:configuration net datalinks vnic> cd ..

VLAN ID를 지정하려면 다음과 같이 하십시오.

hostname:configuration net datalinks vnic (uncommitted)> set id=100
                              id = 100 (uncommitted)
hostname:configuration net datalinks vnic> commit
hostname:configuration net datalinks vnic> cd ..

컨트롤러에 대해 IP 인터페이스를 만들고 이를 VNIC에 지정합니다.

hostname:configuration net> interfaces
hostname:configuration net interfaces> ip
hostname:configuration net interfaces ip (uncommitted)> set v4addrs=192.168.1.101/24
                              v4addrs = 192.168.1.101/24 (uncommitted)
hostname:configuration net interfaces ip (uncommited)> set label=management-controller-1
                              label = management-controller-1 (uncommitted)
hostname:configuration net interfaces ip (uncommitted)> set links=vnic1
                              links = vnic1 (uncommitted)
hostname:configuration net interfaces ip (uncommited)> commit

클러스터형 컨트롤러의 경우 IP 인터페이스를 만들고 이를 두번째 컨트롤러에 대한 VNIC에 지정합니다. commit을 입력한 후 done을 입력합니다.

hostname:configuration net interfaces> ip
hostname:configuration net interfaces ip (uncommitted)> set v4addrs=192.168.1.102/24
                              v4addrs = 192.168.1.102/24 (uncommitted)
hostname:configuration net interfaces ip (uncommited)> set label=management-controller-2
                              label = management-controller-2 (uncommitted)
hostname:configuration net interfaces ip (uncommitted)> set links=vnic2
                              links = vnic2 (uncommitted)
hostname:configuration net datalinks vnic (uncommitted)> commit
hostname:configuration net datalinks> done

첫번째 컨트롤러에 대한 경로 지정을 구성합니다. 클러스터형 컨트롤러의 경우 두번째 컨트롤러에 대해 경로 지정을 구성합니다. commit을 입력한 후 done을 입력합니다.

첫번째 컨트롤러:

hostname:configuration net> routing
hostname:configuration net routing> create
hostname:configuration net route (uncommitted)> set destination=0.0.0.0
                        destination = 0.0.0.0 (uncommitted)
hostname:configuration net route (uncommitted)> set mask=0
                          mask = 0 (uncommitted)
hostname:configuration net route (uncommitted)> set interface=vnic1
                      interface = vnic1 (uncommitted)
hostname:configuration net route (uncommitted)> set gateway=192.168.1.1
                         gateway = 192.168.1.1 (uncommitted)
hostname:configuration net route (uncommitted)> set family=IPv4
                          family = IPv4
hostname:configuration net route (uncommitted)> commit
hostname:configuration net route> done

두번째 컨트롤러:

hostname:configuration net> routing
hostname:configuration net routing> create
hostname:configuration net route (uncommitted)> set destination=0.0.0.0
                        destination = 0.0.0.0 (uncommitted)
hostname:configuration net route (uncommitted)> set mask=0
                          mask = 0 (uncommitted)
hostname:configuration net route (uncommitted)> set interface=vnic2
                      interface = vnic2 (uncommitted)
hostname:configuration net route (uncommitted)> set gateway=192.168.1.1
                         gateway = 192.168.1.1 (uncommitted)
hostname:configuration net route (uncommitted)> set family=IPv4
                          family = IPv4
hostname:configuration net route (uncommitted)> commit
hostname:configuration net route> done

Untitled Interface(제목 없는 인터페이스)인 기본 인터페이스를 삭제하고 cd ..를 입력한 후 done을 입력합니다.

주 - 인터페이스가 삭제되면 인터페이스와 연관된 모든 경로도 제거됩니다.

hostname:configuration net> interfaces
hostname:configuration net interfaces> show
Interfaces:
    
INTERFACE   STATE     CLASS  LINKS   ADDRS                  LABEL
igb0        up        ip     igb0    192.168.1.101/24       Untitled Interface
vnic1       duplicate ip     vnic1   192.168.1.101/24       management-controller-1
vnic2       duplicate ip     vnic2   192.168.1.102/24       management-controller-2
hostname:configuration net interfaces> destroy igb0
This will destroy "igb0" and any networking objects exclusively built over it.

Are you sure? (Y/N) y

hostname:configuration net interfaces> cd ..
hostname:configuration net> done

관리 인터페이스 구성(CLI)

관련 항목