Updating the Signaling Link and Data Link GPLs

This procedure is used to update the following GPLs: SS7IPGW, IPGWI, SLANHC, SS7HC, SS7EPM, IPLHC, IPGHC, ATMHC, and IPSG. These names are used as the value of the gpl parameter of the chg-gpl, act-gpl, rept-stat-gpl, and rtrv-gpl commands.

Signaling links are assigned to cards running the following GPLs: SS7IPGW, IPGWI, SS7HC, SS7EPM, IPLHC, IPGHC, ATMHC, and IPSG. The signaling link GPLs are assigned to the card types shown in Table 3-1.

Table 3-1 SS7 LIM Card Types

GPL	Card Type
atmansi, atmhc	limatm (cards running the atmhc GPL must be E5-ATM cards)
atmitu, atmhc	lime1atm (cards running the atmhc GPL must be E5-ATM cards)
ss7ipgw, ipgwi, iplhc, ipghc, ipsg	dcm (cards running the iplhc, ipghc, or ipsg GPLs must be E5-ENET cards)
ss7hc	lime1, limt1 (these cards can be HC MIMs or E5-E1T1 cards)

Data links are assigned to cards running the SLANHC GPLs. The data link GPLs are assigned to the card types shown in Table 3-2.

Table 3-2 Data Link Card Types

GPL	Card Type
slanhc	dcm (these cards must be E5-ENET, E5-ENET-B, or SLIC cards)

The card types shown in Table 3-1 and Table 3-2 are the values used for the type parameter of the ent-card command.

The cards running the SS7HC GPL are E5-E1T1-B cards. E5-E1T1-B cards are single-slot cards that can support up to 32 signaling links. These cards are either LIM-E1 or LIM-T1 cards. The rtrv-card output shows these cards running either the SS7ANSI or CCS7ITU applications, but the rept-stat-card and rept-stat-gpl output shows that these cards are actually running the SS7HC GPL.

The cards running the SS7EPM GPL are E5-E1T1 cards which are single-slot cards that can support up to 32 signaling links. The E5-E1T1 cards are either LIM-E1 or LIM-T1 cards. The rtrv-card output shows these cards running either the SS7ANSI or CCS7ITU applications, but the rept-stat-card and rept-stat-gpl output shows that these cards are actually running the SS7EPM GPL.

The cards running the IPLHC and IPGHC GPLs are E5-ENET, E5-ENET-B and SLIC cards supporting IP signaling links. The rtrv-card output shows this card running either the IPLIM or IPLIMI applications, but the rept-stat-card and rept-stat-gpl output shows that these cards are actually running the IPLHC GPL. The IPGHC GPL allows the E5-ENET card to support SS7IPGW (ANSI IP Gateway) or IPGWI (ITU IP Gateway) signaling links. The rtrv-card output shows this card running either the SS7IPGW or IPGWI applications, but the rept-stat-card and rept-stat-gpl output shows that these cards are actually running the IPGHC GPL.

The cards running the ATMHC GPL are cards that can contain the ATM high-speed signaling links on E5-ATM cards. The rtrv-card output shows these cards running either the ATMANSI or ATMITU applications, but the rept-stat-card and rept-stat-gpl output shows that these cards are actually running the ATMHC GPL.

The cards running the SLANHC GPLs are the STPLAN cards supporting the STPLAN feature. E5-SLAN cards run the SLANHC GPL. The rtrv-card output shows these cards running the STPLAN application, but the rept-stat-card and rept-stat-gpl output shows that these cards are actually running the SLANHC GPLs.

If the GPL is being updated to a new version, a removable media containing the GPL being updated is required.

If any card is not running the version of the GPL shown in the RELEASE column of the rtrv-gpl output, the indicator ALM is displayed next to the GPL version in the RUNNING column of the rept-stat-gpl output, and next to the GPL version in the APPROVED column in the rtrv-gpl output.

Canceling the REPT-STAT-SLK and RTRV-SLK Commands

Because the rept-stat-slk and rtrv-slk commands used in this procedure can output information for a long period of time, the rept-stat-slk and rtrv-slk commands can be canceled and the output to the terminal stopped. There are three ways that the rept-stat-slk and rtrv-slk commands can be canceled.

• Press the F9 function key on the keyboard at the terminal where the rept-stat-slk or rtrv-slk commands command were entered.
• Enter the canc-cmd without the trm parameter at the terminal where the rept-stat-slk or rtrv-slk commands were entered.
• Enter the canc-cmd:trm=<xx>, where <xx> is the terminal where the rept-stat-slk or rtrv-slk commands were entered, from another terminal other that the terminal where the rept-stat-slk or rtrv-slk commands were entered. To enter the canc-cmd:trm=<xx> command, the terminal must allow Security Administration commands to be entered from it and the user must be allowed to enter Security Administration commands. The terminal’s permissions can be verified with the rtrv-secu-trm command. The user’s permissions can be verified with the rtrv-user or rtrv-secu-user commands.

For more information about the canc-cmd command, go to Commands User's Guide.

1. Verify the control cards that are installed in the EAGLE.

   Refer to Maintenance and Administration Subsystem for information about the control cards.

2. Check the E5-MASPs for removable media.

   If removable media is installed in both E5-MASPs, continue the procedure with 4.

   If removable media is not installed in both E5-MASPs, continue the procedure with 3.

3. Verify the active MASP by entering the rept-stat-db command.

   This is an example of the possible output.

   rlghncxa03w 09-03-16 15:25:40 GMT  EAGLE 46.3.0
   DATABASE STATUS: >> OK <<
           E5TDM 1114 ( STDBY)                 E5TDM 1116 ( ACTV )
           C   LEVEL    TIME LAST BACKUP     C   LEVEL    TIME LAST BACKUP
           - -------- ---------------------- - -------- ----------------------
   FD BKUP Y       36 09-02-19 09:38:25 GMT  Y       36 09-02-19 09:38:25 GMT
   FD CRNT Y       39                        Y       39
           E5MCAP 1113                       E5MCAP 1115
           - --------                        - --------
   RD BKUP -    -         -        -         Y       36 09-02-19 09:27:17 GMT
   USB BKP -    -         -        -         Y        3 09-02-07 01:11:22 GMT
   

   If removable media is installed in the active MASP, continue the procedure with 4.

   If removable media is not installed in the active MASP, insert the removable media in the removable media drive in the active MASP. For more information about inserting removable media in the removable media drive, refer to Removable USB Drive. After the removable media has been inserted in the removable media drive in the active MASP, continue the procedure with 4.

4. Display the GPLs on the fixed disk using the rtrv-gpl command with the gpl parameter value equal to the GPL being updated. These are examples of the possible output.

   rtrv-gpl:gpl=ss7hc

   rlghncxa03w 09-03-16 11:34:04 GMT  EAGLE 46.3.0
   GPL Auditing  ON
   
   GPL       CARD  RELEASE      APPROVED         TRIAL        REMOVE TRIAL
   SS7HC     1114  132-002-000  132-002-000      132-001-000  132-003-000
   SS7HC     1116  132-002-000  132-002-000      132-001-000  132-003-000
   SS7HC     1115  -----------  -----------      -----------  -----------
   

   rtrv-gpl:gpl=slanhc

   rlghncxa03w 09-03-16 11:34:04 GMT  EAGLE 46.3.0
   GPL Auditing  ON
   
   GPL       CARD  RELEASE      APPROVED         TRIAL        REMOVE TRIAL
   SLANHC   1114  132-002-000  132-002-000      132-001-000  132-003-000
   SLANHC   1116  132-002-000  132-002-000      132-001-000  132-003-000
   SLANHC   1115  -----------  -----------      -----------  -----------
   

   If the version of the GPL shown in the REMOVE TRIAL column of the rtrv-gpl output is not the version that is to be loaded onto the cards, remove the removable media from the active MASP.

   Insert the removable media that contains the GPL that is being updated into the removable media drive in the active MASP and repeat this step.

   For more information about inserting removable media in the removable media drive, or removing removable media from the removable media drive, refer to Removable USB Drive.

   If the version of the GPL shown in the REMOVE TRIAL column of the rtrv-gpl output is the version that is to be loaded onto the cards, continue the procedure with 5.

5. Change the GPLs, using the chg-gpl command and specifying the value for the trial GPL shown in the REMOVE TRIAL column in the output of the rtrv-gpl command used in 4.

   For this example, enter these commands.

   chg-gpl:gpl=ss7hc:ver=123-003-000

   These messages should appear.

   rlghncxa03w 09-03-16  11:43:04  GMT  EAGLE 46.3.0
   GPL Auditing  ON
   
   SS7HC upload on 1114 completed
   SS7HC upload on 1116 completed
   System Release ID table upload 1114 completed
   System Release ID table upload 1116 completed
   

   chg-gpl:gpl=slanhc:ver=123-003-000

   These messages should appear.

   rlghncxa03w 09-03-16  11:43:04  GMT  EAGLE5 46.3.0
   GPL Auditing  ON
   
   SLANHC upload on 1114 completed
   SLANHC upload on 1116 completed
   System Release ID table upload 1114 completed
   System Release ID table upload 1116 completed
   

6. Activate the trial GPL, using the act-gpl command and specifying the value for the trial GPL shown in 5.

   For this example, enter this command.

   act-gpl:gpl=ss7hc:ver=123-003-000

   These messages should appear.

   rlghncxa03w 09-03-16 06:54:39 GMT EAGLE 46.3.0
   SS7HC activate on 1114 completed
   SS7HC activate on 1116 completed
   

   act-gpl:gpl=slanhc:ver=123-003-000

   These messages should appear.

   rlghncxa03w 09-03-16 06:54:39 GMT EAGLE 46.3.0
   SLANHC activate on 1114 completed
   SLANHC activate on 1116 completed
   

7. Verify that the trial GPL has been made the approved GPL using the rtrv-gpl command with the gpl parameter value specified in 5 and 6.

   For this example, enter these commands.

   rtrv-gpl:gpl=ss7hc

   This is an example of the possible output.

   rlghncxa03w 09-03-16 11:34:04 GMT EAGLE 46.3.0
   GPL Auditing  ON
   
   GPL       CARD  RELEASE      APPROVED         TRIAL        REMOVE TRIAL
   SS7HC     1114  132-003-000  132-003-000      132-002-000  132-003-000
   SS7HC     1116  132-003-000  132-003-000      132-002-000  -----------
   

   If E5-based control cards are installed in the EAGLE, this is an example of the possible output.

   rlghncxa03w 09-03-16 11:34:04 GMT  EAGLE 46.3.0
   GPL Auditing  ON
   
   GPL       CARD  RELEASE      APPROVED         TRIAL        REMOVE TRIAL
   SS7HC     1114  132-003-000  132-003-000      132-002-000  132-003-000
   SS7HC     1116  132-003-000  132-003-000      132-002-000  132-003-000
   SS7HC     1115  -----------  -----------      -----------  -----------
   

   rtrv-gpl:gpl=slanhc

   This is an example of the possible output.

   rlghncxa03w 09-03-16 11:34:04 GMT EAGLE 46.3.0
   GPL Auditing  ON
   
   GPL       CARD  RELEASE      APPROVED         TRIAL        REMOVE TRIAL
   SLANHC   1114  132-003-000  132-003-000      132-002-000  132-003-000
   SLANHC   1116  132-003-000  132-003-000      132-002-000  -----------
   

   If E5-based control cards are installed in the EAGLE, this is an example of the possible output.

   rlghncxa03w 09-03-16 11:34:04 GMT  EAGLE 40.1.0
   GPL Auditing  ON
   
   GPL       CARD  RELEASE      APPROVED         TRIAL        REMOVE TRIAL
   SLANHC   1114  132-003-000  132-003-000      132-002-000  132-003-000
   SLANHC   1116  132-003-000  132-003-000      132-002-000  132-003-000
   SLANHC   1115  -----------  -----------      -----------  -----------
   

8. Verify which cards are running the GPL using the rept-stat-gpl command with the gpl parameter value specified in 7.

   For this example, enter these commands.

   rept-stat-gpl:gpl=ss7hc

   This is an example of the possible output.

   rlghncxa03w 09-03-16 11:40:26 GMT  EAGLE 46.3.0
   GPL      CARD   RUNNING           APPROVED      TRIAL
   SS7HC    1201   132-002-000 ALM   132-003-000   132-002-000
   SS7HC    1204   132-002-000 ALM   132-003-000   132-002-000
   SS7HC    1211   132-002-000 ALM   132-003-000   132-002-000
   SS7HC    1215   132-002-000 ALM   132-003-000   132-002-000
   SS7HC    1307   132-002-000 ALM   132-003-000   132-002-000
   SS7HC    2111   132-002-000 ALM   132-003-000   132-002-000
   SS7HC    2112   132-002-000 ALM   132-003-000   132-002-000
   SS7HC    2115   132-002-000 ALM   132-003-000   132-002-000
   SS7HC    2116   132-002-000 ALM   132-003-000   132-002-000
   Command Completed
   

   Continue the procedure by performing one of these steps.

   • If one of these GPLs is being updated: SS7IPGW, IPGWI, SS7HC, SS7EPM, IPLHC, IPGHC, ATMHC, or IPSG, continue the procedure with 9.
   • If one of these GPLs is being updated: SLANHC, continue the procedure with 11.
9. Display the signaling links associated with the cards shown in 8.

   Enter the rtrv-slk command. This is an example of the possible output.

   rlghncxa03w 09-07-16 21:16:37 GMT EAGLE 41.1.0
   
                                      L2T               PCR  PCR
   LOC  LINK LSN         SLC TYPE     SET  BPS    ECM   N1   N2
   1201 A    lsnmpl1      0  LIMDS0   2    56000  BASIC ---  -----
   1201 B    lsnmpl2      0  LIMDS0   3    56000  PCR   76   3800
   1201 A1   lsnmpl3      0  LIMDS0   2    56000  PCR   120  5034
   1201 B1   lsnmpl4      0  LIMDS0   1    56000  BASIC ---  -----
   1204 A    lsnmpl1      1  LIMDS0   2    56000  BASIC ---  -----
   1204 B    lsnmpl2      1  LIMDS0   3    56000  PCR   76   3800
   1204 A2   lsnmpl3      1  LIMDS0   2    56000  PCR   120  5034
   1204 B2   lsnmpl5      0  LIMDS0   3    56000  PCR   76   3800
   1211 A    lsnmpl1      2  LIMDS0   2    56000  BASIC ---  -----
   1211 B    lsnmpl3      2  LIMDS0   2    56000  PCR   120  5034
   1211 A3   lsnmpl5      1  LIMDS0   3    56000  PCR   76   3800
   1211 B3   lsnmpl6      0  LIMDS0   1    56000  PCR   120  5034
   1215 A1   lsnmpl7      0  LIMDS0   1    56000  BASIC ---  -----
   1215 B2   lsnmpl1      3  LIMDS0   2    56000  BASIC ---  -----
   1215 A3   lsnmpl6      1  LIMDS0   1    56000  PCR   120  5034
   1215 B3   lsnmpl7      1  LIMDS0   1    56000  BASIC ---  -----
   1307 A    lsnmpl6      2  LIMDS0   1    56000  PCR   120  5034
   1307 B2   lsnmpl7      2  LIMDS0   1    56000  BASIC ---  -----
   1307 A3   lsnmpl6      3  LIMDS0   1    56000  PCR   120  5034
   1307 B3   lsnmpl7      3  LIMDS0   1    56000  BASIC ---  -----
   
                                      LP            ATM
   LOC  LINK LSN         SLC TYPE     SET  BPS      TSEL      VCI    VPI   LL
   1302 A    atm1302a     5  LIMATM   3    1544000  INTERNAL  35     15    0
   1305 A    atm1305a     5  LIMATM   5    1544000  LINE      5      0     2
   
                                      LP         ATM                    E1ATM
   LOC  LINK LSN         SLC TYPE     SET BPS    TSEL     VCI   VPI  CRC4 SI SN
   2101 A    atmitu1      0  LIME1ATM 5   2.048M LINE     150   2    ON   1  20
   2105 A    atmitu1      1  LIME1ATM 5   2.048M LINE     35    15   ON   2  15
   
                                      L2T               PCR  PCR   E1   E1
   LOC  LINK LSN         SLC TYPE     SET  BPS    ECM   N1   N2    LOC  PORT TS
   2111 A    lsne145      0  LIME1    1    56000  BASIC ---  ----- 2111 2    10
   2112 A    lsne145      1  LIMCH    1    56000  BASIC ---  ----- 2111 1    14
   2112 A2   lsne145      2  LIMCH    1    56000  BASIC ---  ----- 2111 1    20
   
                                      L2T               PCR  PCR   T1   T1
   LOC  LINK LSN         SLC TYPE     SET  BPS    ECM   N1   N2    LOC  PORT TS
   2115 A    lsnt145      0  LIMT1    1    56000  BASIC ---  ----- 2115 2    3
   2116 A    lsnt145      1  LIMCH    1    56000  BASIC ---  ----- 2115 1    11
   2116 A2   lsnt145      2  LIMCH    1    56000  BASIC ---  ----- 2115 1    19
   
   SLK table is (30 of 1200) 3% full.
   

10. Using the outputs of 8 and 9 as a guide, select a card to load the approved GPL onto.

    Deactivate the SS7 signaling links on that card using the dact-slk command. For this example, enter these commands.

    dact-slk:loc=1201:link=a

    dact-slk:loc=1201:link=b

    dact-slk:loc=1201:link=a1

    dact-slk:loc=1201:link=b1

    Caution:

    These command examples place the SS7 signaling links on card 1201 out of service. This will interrupt service on the SS7 signaling links on card 1201 and allow the approved GPL to be loaded on to card 1201.

    Do not deactivate all the SS7 signaling links in the EAGLE at the same time. Doing so will take all the SS7 signaling links out of service and isolate the EAGLE from the network.

    When each of these commands have successfully completed, this message should appear.

    rlghncxa03w 09-03-16 11:45:18 GMT  EAGLE 46.3.0
    Deactivate SLK message sent to card
    

    Continue the procedure with 13.

11. Display the data links, and their status, associated with the cards shown in 8.

    Enter the rept-stat-dlk command. This is an example of the possible output.

    rlghncxa03w 09-03-16 17:00:36 GMT  EAGLE 46.3.0
    DLK    PST           SST        AST
    2105   IS-NR         Avail      ---
    2113   IS-NR         Avail      ---
    2301   IS-NR         Avail      ---
    Command Completed.
    

12. Deactivate the TCP/IP data link on the card (shown in 11) that you wish to load the trial GPL onto, using the canc-dlk command.

    For this example, enter this command.

    canc-dlk:loc=2105

    Caution:

    This command example places the TCP/IP data link on card 2105 out of service. This will interrupt service on the TCP/IP data link on card 2105 and allow the trial GPL to be loaded on to card 2105.

    Do not deactivate all the TCP/IP data links in the EAGLE at the same time. Doing so will take all the TCP/IP data links out of service and cause the STPLAN feature to be disabled.

    If there is only one TCP/IP data link in the EAGLE, placing the card out of service will cause the STPLAN feature to be disabled.

    When this command has successfully completed, this message should appear.

    rlghncxa03w 09-03-16 11:45:18 GMT  EAGLE 46.3.0
    Deactivate Link message sent to card.
    Command Completed.
    

13. Place the card specified in either 10 or 12 out of service using the rmv-card command.

    If the card contains the last signaling link in a linkset, the force=yes parameter must be specified. For this example, enter this command.

    rmv-card:loc=1201:force=yes

    rmv-card:loc=2105

    When this command has successfully completed, this message should appear.

    rlghncxa03w 09-03-16  11:11:28 GMT  EAGLE 46.3.0
    Card has been inhibited.
    

14. Put the cards that were inhibited in 13 back into service using the rst-card command.

    The rst-card command also loads the approved version of the GPL onto the card.

    For this example, enter this command.

    rst-card:loc=1201

    rst-card:loc=2105

    When this command has successfully completed, this message should appear.

    rlghncxa03w 09-03-16  11:11:28 GMT  EAGLE 46.3.0
    Card has been allowed.
    

15. Verify the GPLs on the cards using the rept-stat-gpl command with the gpl parameter value specified in 8.

    If any card is not running the release version of the GPL, shown in the RELEASE column of the rtrv-gpl output in 7, the indicator ALM is displayed next to the GPL version in the RUNNING column of the rept-stat-gpl output. For this example, enter these commands.

    rept-stat-gpl:gpl=ss7hc

    This is an example of the possible output.

    rlghncxa03w 09-03-16 11:40:26 GMT  EAGLE 46.3.0
    GPL      CARD   RUNNING           APPROVED      TRIAL
    SS7HC    1201   132-003-000       132-003-000   132-002-000
    SS7HC    1204   132-002-000 ALM   132-003-000   132-002-000
    SS7HC    1211   132-002-000 ALM   132-003-000   132-002-000
    SS7HC    1215   132-002-000 ALM   132-003-000   132-002-000
    SS7HC    1307   132-002-000 ALM   132-003-000   132-002-000
    SS7HC    2111   132-002-000 ALM   132-003-000   132-002-000
    SS7HC    2112   132-002-000 ALM   132-003-000   132-002-000
    SS7HC    2115   132-002-000 ALM   132-003-000   132-002-000
    SS7HC    2116   132-002-000 ALM   132-003-000   132-002-000
    Command Completed
    

    rept-stat-gpl:gpl=slanhc

    This is an example of the possible output.

    rlghncxa03w 09-03-16 11:40:26 GMT  EAGLE 46.3.0
    GPL      CARD   RUNNING           APPROVED      TRIAL
    SLANHC  2105   132-003-000       132-003-000   132-002-000
    SLANHC  2113   132-002-000 ALM   132-003-000   132-002-000
    SLANHC  2301   132-002-000 ALM   132-003-000   132-002-000
    Command Completed
    

    Continue the procedure by performing one of these steps.

    • If one of these GPLs is being updated: SS7IPGW, IPGWI, SS7HC, SS7EPM, IPLHC, IPGHC, ATMHC, or IPSG, continue the procedure with 16.
    • If one of these GPLs is being updated: SLANHC, continue the procedure with 18.
16. Place the signaling links that were deactivated in 10 back into service using the act-slk command.

    For this example, enter these commands.

    act-slk:loc=1201:link=a

    act-slk:loc=1201:link=b

    act-slk:loc=1201:link=a1

    act-slk:loc=1201:link=b1

    When each of these commands have successfully completed, this message should appear.

    rlghncxa03w 09-03-16 11:55:49 GMT  EAGLE 46.3.0
    Activate SLK message sent to card
    

17. Verify that the signaling links activated in 16 are back in service using the rept-stat-slk command with the card location and signaling link.

    For this example, enter these commands.

    rept-stat-slk:loc=1201:link=a

    This is an example of the possible output.

    rlghncxa03w 09-03-16 13:06:25 GMT EAGLE 46.3.0
    SLK      LSN       CLLI        PST          SST       AST
    1201,A   lsnmpl1   ----------- IS-NR        Avail     ----
      ALARM STATUS       = No Alarms.
      UNAVAIL REASON     = --
    

    rept-stat-slk:loc=1201:link=b

    This is an example of the possible output.

    rlghncxa03w 09-03-16 13:06:25 GMT EAGLE 46.3.0
    SLK      LSN       CLLI        PST          SST       AST
    1201,B   lsnmpl2   ----------- IS-NR        Avail     ----
      ALARM STATUS       = No Alarms.
      UNAVAIL REASON     = --
    

    rept-stat-slk:loc=1201:link=a1

    This is an example of the possible output.

    rlghncxa03w 09-03-16 13:06:25 GMT EAGLE 46.3.0
    SLK      LSN       CLLI        PST          SST       AST
    1201,A1  lsnmpl3   ----------- IS-NR        Avail     ----
      ALARM STATUS       = No Alarms.
      UNAVAIL REASON     = --
    

    rept-stat-slk:loc=1201:link=b1

    This is an example of the possible output.

    rlghncxa03w 09-03-16 13:06:25 GMT EAGLE 46.3.0
    SLK      LSN       CLLI        PST          SST       AST
    1201,B1  lsnmpl4   ----------- IS-NR        Avail     ----
      ALARM STATUS       = No Alarms.
      UNAVAIL REASON     = --
    Command Completed.
    

18. Place the TCP/IP data link that was deactivated in 12 back into service using the act-dlk command.

    For this example, enter this command.

    act-dlk:loc=2105

    When this command has successfully completed, this message should appear.

    rlghncxa03w 09-03-16 11:55:49 GMT  EAGLE 46.3.0
    Activate Link message sent to card.
    

19. Verify that the TCP/IP date links activated in 18 are back in service with the rept-stat-dlk command.

    This is an example of the possible output.

    rlghncxa03w 09-03-16 12:57:50 GMT EAGLE 46.3.0
    DLK    PST           SST        AST
    2105   IS-NR         Avail      ---
    2113   IS-NR         Avail      ---
    2301   IS-NR         Avail      ---
    Command Completed.
    

20. Continue the procedure by performing these actions.
    When the E5-based control cards are installed in the EAGLE, continue the procedure by performing one of these actions:

    • If you wish to load the new GPL onto the other cards shown in 8, repeat this procedure from either 10 or 12 for each card shown in 8.
    • If the new GPL will not be loaded onto other cards but other GPLs will be updated, repeat this procedure from 1.
    • If the new GPL will not be loaded onto other cards and no other GPLs are being updated, then this procedure is finished.

Figure 3-2 Updating the Signaling Link and Data Link GPLs

Sheet 1 of 5

Sheet 2 of 5

Sheet 3 of 5

Sheet 4 of 5

Sheet 5 of 5