Table of Contents
- Title and Copyright Information
- My Oracle Support (MOS)
- What's New in This Guide
- 1 Introduction
-
2
Configuring Destination Tables
- Introduction
- Point Code Formats
- 14-Bit ITU National Point Code Formats
- ITU National Duplicate Point Codes
- Proxy Point Codes
- Changing the Proxy Point Code Quantity
- Changing the DPC Quantity
- Activating the ITU National and International Spare Point Code Support Feature
- Spare Point Code Feature Migration Plan
- Multiple Point Code Support
- Adding a Secondary Point Code
- Removing a Secondary Point Code
- Adding a Point Code to the Self-Identification of the EAGLE
- Changing the Self-Identification of the EAGLE
- Cluster Routing and Management Diversity (CRMD)
- Nested Cluster Routing
- Adding a Cluster Point Code
- Changing the Attributes of a Cluster Point Code
- Network Routing
- Adding a Network Routing Point Code
- Adding a Destination Point Code
- Removing a Destination Point Code
- Changing a Destination Point Code
- Changing the Group Code Assigned to a 14-Bit ITU National Point Code
-
3
SS7 Configuration
- Introduction
- Enabling the Large System # Links Controlled Feature
- Adding an SS7 Linkset
- ITU SLS Enhancement
- ITU TFR Procedures
- Per-Linkset Random SLS
- Verifying the Gateway Screening Configuration for a Linkset
- Configuring the MTP Restart Feature
- Configuring the 5-Bit to 8-Bit SLS Conversion Feature
- Using Proxy Point Codes and Secondary Point Codes when Adding a Linkset
- Activating the SLS Bit Rotation by Incoming Linkset Feature
- Configuring the RSLS8 Value for ANSI Linksets
- Removing a Linkset Containing SS7 Signaling Links
- Changing an SS7 Linkset
- Verifying the New Adjacent Point Code or New Secondary Point Code for a Linkset
- Using the MULTGC Parameter when Changing the Attributes of a Linkset
- Configuring an ITU Linkset with a Secondary Adjacent Point Code (SAPC)
- Adding an SS7 Signaling Link
- Removing an SS7 Signaling Link
- Adding a Route Containing an SS7 DPC
- Adding a Route Containing a Cluster Point Code
- Adding a Route Containing an IPGWx Linkset
- Removing a Route
- Changing a Route
- Changing Level 2 Timers
- Changing Level 3 Timers
- Changing a Signaling Link Test Message
- Configuring Circular Route Detection
- Configuring the TFA/TFR Pacing Rate
- Configuring the Frequency of RST Messages on Low Priority Routes
- Adding Remote Loopback Points
- Removing Remote Loopback Points
- Changing Remote Loopback Points
- Configuring the System for Random SLS Generation
- Configuring the Options for the TDM Global Timing Interface
- Configuring the Restricted Linkset Option
- Configuring the Options for Handling TFCs on ITU-I and ITU-N Networks
- Changing the High-Capacity Card Temperature Alarm Thresholds
- Activating the Origin-Based MTP Routing Feature
- Configuring the Origin-Based MTP Routing SCCP OPC Option
- Adding an Exception Route Entry
- Removing a Route Exception Entry
- Changing a Route Exception Entry
- Activating the Circular Route Auto-Recovery Feature
- Turning Off the Circular Route Auto-Recovery Feature
- Activating the Enhanced Far-End Loopback Detection Feature
- Turning Off the Enhanced Far-End Loopback Detection Feature
- Activating the Multiple Linksets to Single Adjacent PC (MLS) Feature
- Configuring the ITU Linkset NI Mapping Options
- Configuring the Option for Handling Message Priorities for Messages Crossing into ITU-I and ITU-N Networks
- Activating the 6-Way Loadsharing on Routesets Feature
- 4 Point Code and CIC Translation Configuration
-
A
E1 Interface
- Introduction
- Determining the Configuration
- E1 Interface Configuration Procedures
- Adding a LIM-E1 Card
- Removing a LIM-E1 Card
- Adding Channelized and non-Channel Bridged E1 Ports
- Adding Channel Bridged E1 Ports
- Adding Unchannelized E1 Ports
- Removing the E1 Interface Parameters
- Changing the Attributes of a Channelized E1 Port
- Changing the Attributes of an Unchannelized E1 Port
- Making a Channel Bridged E1 Port from a Channelized E1 Port
- Making a Non-Channel Bridged E1 Port from a Channel Bridged E1 Port
- Adding an E1 Signaling Link
-
B
T1 Interface
- Introduction
- Determining the Configuration
- T1 Interface Configuration Procedures
- Adding a LIM-T1 Card
- Removing a LIM-T1 Card
- Adding Channelized and non-Channel Bridged T1 Ports
- Adding Channel Bridged T1 Ports
- Adding Unchannelized T1 Ports
- Removing the T1 Interface Parameters
- Changing the Attributes of a Channelized T1 Port
- Changing the Attributes of an Unchannelized T1 Port
- Making a Channel Bridged T1 Port from a Channelized T1 Port
- Making a Non-Channel Bridged T1 Port from a Channel Bridged T1 Port
- Adding a T1 Signaling Link
-
C
ATM Signaling Link Configuration
- Introduction
- Overview of the ATM High-Speed Signaling Link LIM Operation
- ATM High-Speed Signaling Link Testing Capability
- Large MSUs
- Unsolicited Messages
- ATM High-Speed Signaling Link Configuration
- Adding an ATM High-Speed LIM
- Changing the Three Links per E5-ATM-B Card Quantity
- Adding an ATM High-Speed Signaling Link
- Changing an ATM High-Speed Signaling Link Parameter Set
- D Reference Information