4.278 enable-ctrl-feat

Use this command to enable a controlled feature that the customer is entitled to use.

Note:

The “LNP (Local Number Portability) feature” is turned on when the LNP ported TNs quantity is greater than 0 in the rtrv-ctrl-feat command output (an LNP ported TNs quantity feature access key has been enabled and turned on).

Parameters

partnum (mandatory)
Part number. The part number for the feature.
Range:
893000000 - 893999999

Do not include dashes in the 9-digit number.

fak (optional)
Feature Access Key. The Feature Access Key for the feature.
Range:
ayyyyyyyyyyyy

13 alphanumeric characters

Note:

The FAK parameter has no significance starting with Release 46.3. The parameter is used only for backward compatibility.

Example

enable-ctrl-feat:partnum=893xxxxxx

Dependencies

The phrase "Service Module cards" refers to E5-SM4G or E5-SM8G-B cards when any of these cards can be used. If a specific card is required, then the appropriate requirement is listed.

The Dual ExAP Config feature cannot be enabled before the E5-SM4G Throughput Cap feature is enabled.

The system serial number must be locked in the database before this command can be entered for the feature (see the ent-serial-num command).

A feature cannot be enabled with this command when the feature has already been enabled with a permanently ON feature access key or a feature access key for a quantity that is greater than the quantity specified in the command.

The GTT feature must be on before the IDP Screening for Prepaid feature can be enabled.

The value specified for the partnum parameter must be the correct part number for the feature.

A valid system serial number must be entered in the database before this command can be entered for the feature (see the ent-serial-num command).

The Feature Control database (FEATCTRL.TBL) is corrupt; database maintenance is required.

The LNP ELAP Configuration feature and the WNP feature must be turned on before the LNP SMS feature can be enabled.

The GTT feature must be turned on before the XGTT Table Expansion feature can be enabled.

Both cards that run the OAM application in the system must be GPSM-II cards before the XGTT Table Expansion feature can be enabled.

The DSTN5000 feature bit for the 5000 Routesets feature must be turned on before the 6000 Routesets, 7000 Routesets, 8000 Routesets, or 10,000 Routesets feature can be enabled.

The 7000 Routesets or 8000 Routesets feature cannot be enabled if more than 8000 alias point codes are already assigned in the system.

The 10,000 Routesets feature cannot be enabled if more than 10000 alias point codes are already assigned in the system.

If the LNP (an LNP ported TNs quantity), LNP 150,000 LRNs, or LNP 300,000 NPANXX feature is enabled, then none of the following features can be enabled unless the Dual ExAP Config feature is enabled:

  • AINPQ
  • A-Port
  • ATINP
  • Equipment Identity Register (EIR)
  • Diameter Equipment Identity Register (DEIR)
  • G-Flex 
  • G-Port
  • Info Analyzed Relay Base (IAR Base) 
  • INP 
  • IS41 GSM Migration (IGM)
  • MO SMS ASD
  • MO SMS GRN
  • MO-based GSM SMS NP
  • MO-based IS41 SMS NP
  • MTP Msgs for SCCP Apps
  • Portability Check for MO SMS  
  • Prepaid IDP Query Relay (IDP Relay)
  • Prepaid SMS Intercept Phase 1 (PPSMS) 
  • TIF Number Portability
  • TIF Number Substitution
  • TIF Subscriber CgPN Blacklist
  • V-Flex 

The LNP feature (an LNP ported TNs quantity) must be enabled before the LNP 150,000 LRNs feature or the LNP 300.000 NPANXXs feature can be enabled.

A card with unknown hardware is detected in system (possibly in the process of loading, or a loading error has occurred).

The LNP ELAP Configuration feature must be enabled and turned on before any LNP quantity features can be enabled.

The LNP feature for 24 million TNs requires all Service Module cards with a minimum of 2GB of memory.

The LNP feature for 36 million TNs requires all Service Module cards with a minimum of 3GB of memory.

The LNP feature for LNP ported TNs quantities of 48 million TNs to 192 million TNs requires all Service Module cards with a minimum of 4GB of memory.

The LNP feature for LNP ported TNs quantities of 204 million TNs to 228 million TNs requires all Service Module cards with a minimum of 4GB of memory.

The 150,000 LNP LRNs feature requires all Service Module cards with a minimum of 2GB of memory.

The 300,000 LNP NPANXXs feature requires all Service Module cards with a minimum of 2GB of memory.

The GTT feature bit must be turned on (see the chg-feat command) before the following features can be enabled:

  • Advanced GT Modification (AMGTT)
  • ANSI41 AIQ
  • ATI Number Portability Query (ATINP)
  • Dual ExAP Config
  • E5-SM4G Throughput Capacity
  • Equipment Identity Register (EIR)
  • G-Flex
  • GSM Map Screening (GSM)
  • Hex Digit Support for GTT
  • Info Analyzed Relay Base (IAR Base)
  • Intermediate GTT Loadsharing (IGTTLS)
  • LNP ELAP Configuration
  • LNP ported LRNs
  • LNP ported NPANXXs
  • LNP ported TNs 
  • MO SMS ASD
  • MO SMS GRN
  • MO SMS IS41-to-GSM Migration
  • MO-based GSM SMS NP
  • MO-based IS41 SMS NP
  • MTP Msgs for SCCP Apps
  • MTP Routed Gateway Screening Stop Action
  • Portability Check for MO SMS (MNPSMS)
  • Prepaid SMS Intercept Ph1 (PPSMS)
  • SCCP Loop Detection 
  • TIF Additional Subscriber Data
  • TIF Generic Routing Number
  • TIF Number Portability
  • TIF Number Substitution
  • TIF Range CgPN Blacklist
  • TIF SCS Forwarding
  • TIF Simple Number Substitution
  • TIF Subscriber CgPN Blacklist
  • Transaction-based GTT Loadsharing (TBGTTLS)
  • Voice Mail Router (V-Flex)

If the SCCP Conversion or TCAP Conversion feature is turned on, then the ANSI/ITU SCCP Conversion feature cannot be enabled.

The ANSI/ITU SCCP Conversion feature requires Service Module cards in the system.

The GSM Map Screening (GSM) feature must be turned on before the Enhanced GSM Map Screening (EGSM) feature can be enabled.

The Enhanced GSM Map Screening (EGSM) feature must be turned on before the MTP MAP Screening feature can be enabled.

The Measurements Platform feature must be turned on and the Measurements Platform collection function must be enabled (see the chg-measopts:platformenable=on parameter) before the MTP MAP Screening feature can be enabled (at least one MCPM card must be active).

The G-Port feature must be turned on before the following features can be enabled:

  • GSM MAP SRI Redirect for Serving HLR
  • ISUP NP with EPAP
  • MNP Circular Route Prevention
  • Prepaid SMS Intercept Phase 1 (PPSMS)

The GWS (Gateway Screening) feature must be turned on before the following features can be enabled:

  • Integrated GLS
  • ISUP NP with EPAP
  • TIF Additional Subscriber Data
  • TIF Generic Routing Number
  • TIF Number Portability
  • TIF Number Substitution
  • TIF Range CgPN Blacklist
  • TIF SCS Forwarding
  • TIF Simple Number Substitution
  • TIF Subscriber CgPN Blacklist

The following features cannot be enabled if the ANSIGFLEX system option is enabled (see the chg-stpopts command) AND E5-SM4G Throughput Cap quantity key for 6800 or above has not been enabled:

  • 1100 TPS/DSM for ITU NP
  • ANSI-41 INP Query (AINPQ) 
  • A-Port
  • ATINP
  • Equipment Identity Register (EIR)
  • G-Flex MAP Layer Routing 
  • G-Port
  • Info Analyzed Relay Base
  • INP
  • IS41 GSM Migration (IGM)
  • MO SMS ASD
  • MO SMS GRN
  • MO SMS IS41-to-GSM Migration
  • MO-based GSM SMS NP
  • MO-based IS41 SMS NP
  • Portability Check for MO SMS 
  • TIF Number Portability
  • TIF Number Substitution
  • TIF Selective Screening
  • TIF Subscriber CgPN Blacklist
  • V-Flex

The following features cannot be enabled if the ANSIGFLEX system option is enabled (see the chg-stpopts command) AND DSM is equipped in the system

  • 1100 TPS/DSM for ITU NP
  • ANSI-41 INP Query (AINPQ)
  • A-Port
  • ATINP
  • Equipment Identity Register (EIR)
  • G-Flex MAP Layer Routing
  • G-Port
  • Info Analyzed Relay Base
  • INP
  • IS41 GSM Migration (IGM)
  • MO SMS ASD
  • MO SMS GRN
  • MO SMS IS41-to-GSM Migration
  • MO-based GSM SMS NP
  • MO-based IS41 SMS NP
  • Portability Check for MO SMS
  • TIF Number Portability
  • TIF Number Substitution
  • TIF Selective Screening
  • TIF Subscriber CgPN Blacklist
  • V-Flex

Before an LNP ported TNs quantity greater than 96 million numbers can be enabled, an ELAP system that supports a quantity greater than 96 million numbers must be available to the EAGLE.

  • The ELAP software must be at version 4.0 to support LNP ported TNs quantities greater than 96 million numbers and up to 120 million numbers.
  • The ELAP software must be at version 5.0 or greater to support LNP ported TNs quantities greater than 120 million numbers. A quantity greater than 120 million numbers cannot be enabled until the ELAP is upgraded to the required software level, and the appropriate ELAP commands are issued to convert the 120 Million LNP Numbers database structure to the data compaction structure for more than 120 million numbers.

The rept-stat-mps command can be entered at the EAGLE to determine the ELAP software version.

Service Module cards running the VSCCP application must be present in the system before the following features can be enabled:

  • AINPQ
  • ANSI41 AIQ
  • A-Port
  • ATI Number Portability Query (ATINP)
  • EIR
  • Enhanced GSM MAP Screening (EGMS)
  • Flexible GTT Load Sharing
  • G-Flex
  • G-Port
  • INP
  • IS41 GSM Migration (IGM)
  • LNP ELAP Configuration
  • MO SMS ASD
  • MO SMS B-Party Routing
  • MO SMS GRN
  • MO SMS IS41-to-GSM Migration
  • MO-based GSM SMS NP
  • MO-based IS41 SMS NP
  • Origin-based SCCP Routing  (OBSR)
  • PPSMS 
  • SCCP Loop Detection
  • TIF Additional Subscriber Data
  • TIF Generic Routing Number
  • TIF Number Portability
  • TIF Number Substitution
  • TIF Range CgPN Blacklist
  • TIF SCS Forwarding 
  • TIF Simple Number Substitution
  • TIF Subscriber CgPN Blacklist
  • Transaction-based GTT Loadsharing (TBGTTLS) 
  • Weighted GTT Loadsharing (WGTTLS) 
  • V-Flex 

Before LNP ported TNs quantities greater than 96 million numbers can be enabled, an ELAP system must be available to validate its software version to the EAGLE.

The Enhanced GTT (EGTT) feature must be turned on before the following features can be enabled

  • Flexible Linkset Optional Based Routing (FLOBR) 
  • GTT Action - DISCARD
  • GTT Action - DUPLICATE
  • GTT Action - FORWARD
  • MO SMS B-Party Routing
  • Origin-based SCCP Routing 

At least one of the EPAP-based ITU NP features (G-Port, A-Port, INP, IGM, EIR, IDP Relay, ANSI-41 INP Query, V-Flex, or PPSMS) must be turned on before the 1100 TPS/DSM for ITU NP feature can be enabled.

The GTT feature must be turned on before the A-Port feature can be enabled.

The GTT feature must be turned on before the G-Port feature can be enabled.

The GTT feature must be turned on before the IS41 GSM Migration (IGM) feature can be enabled.

If a DSM card with less than 4 gigabytes of memory is present in the system, the following features cannot be enabled

  • A-Port
  • MO SMS ASD
  • MO SMS B-Party Routing
  • MO SMS GRN
  • MO SMS IS41-to-GSM Migration
  • MO SMS Prepaid Intercept on B-Party
  • Portability Check for MO SMS
  • PPSMS

The PPSMS feature cannot be enabled if the LNP ELAP Configuration feature is turned on.

Service Module cards must be provisioned in the system before the Prepaid IDP Query Relay feature can be enabled.

The GTT feature must be turned on before the Prepaid IDP Query Relay feature can be enabled.

The IP User Interface feature must be enabled before the SEAS Over IP feature can be enabled.

If the TIF (Number Portability/ Additional Subscriber Data / Generic Routing Number) is enabled, then the LNP feature cannot be enabled. If the LNP feature is enabled, then the TIF (Number Portability/ Additional Subscriber Data / Generic Routing Number) feature cannot be enabled.

The Multiple Point Code (MPC) feature must be turned on before the Multiple Linksets to Single Adjacent PC (MLS) feature can be enabled.

The G-Flex feature must be turned on before the G-Flex MAP Layer Routing feature can be enabled.

The STP Options table is corrupt or cannot be found by the system.

The G-Port feature must be enabled before the following features can be enabled:

  • G-Port SRI Query for Prepaid
  • MT-Based GSM SMS NP

The A-Port feature must be enabled before the MT-Based IS41 SMS NP feature can be enabled.

The AMGTT CdPA Only feature cannot be enabled using the enable-ctrl-feat command. This feature is automatically enabled and turned on if the MGTT feature was on before upgrade to EAGLE Release 38.0 occurred.

The AMGTT CdPA Only feature must be turned on before the AMGTT CgPA Upgrade feature can be enabled.

If the AMGTT CdPA Only feature or the AMGTT CgPA Upgrade feature is turned on, then the AMGTT feature cannot be enabled.

The LNP (an LNP ported TNs quantity), LNP 150,000 LRNs, or LNP 300,000 NPANXX feature cannot be enabled if the INP or AINPQ feature is turned on or if any of the features listed below is enabled. If the LNP (an LNP ported TNs quantity), LNP 150,000 LRNs, or LNP 300,000 NPANXX feature is enabled, then none of the features listed below can be enabled.

  • A-Port
  • ATINP
  • Equipment Identity Register (EIR)
  • Diameter Equipment Identity Register (DEIR)
  • G-Flex
  • G-Port
  • Info Analyzed Relay Base (IAR Base)
  • IDP Screening for Prepaid
  • IS41 GSM Migration (IGM)
  • MO SMS ASD
  • MO SMS GRN
  • MO SMS IS41-to-GSM Migration
  • MO-based GSM SMS NP
  • MO-based IS41 SMS NP
  • MTP Msgs for SCCP Apps
  • Portability Check for MO SMS (MNPSMS)
  • Prepaid IDP Query Relay (IDP Relay)
  • Prepaid SMS Intercept Phase 1 (PPSMS)
  • TIF Number Portability
  • TIF Number Substitution
  • TIF Subscriber CgPN Blacklist
  • V-Flex

The MT-Based GSM SMS NP feature must be enabled before the MT-Based GSM MMS NP feature can be enabled.

The LNP ported TNs 24 Million Quantity feature or greater must be turned on before the LRNQT feature can be enabled.

The Intermediate GTT Load Sharing feature must be turned on before the GTT LS ARI feature can be enabled.

The Flexible GTT Load Sharing feature must be enabled before the GTT LS ARI feature can be enabled.

The Flexible Linkset Optional Based Routing (FLOBR) feature must be turned on before the TCAP Opcode Based Routing (TOBR) feature can be enabled.

The Variable Length GTT (VGTT) feature must be turned on before the Support for 16 GTT Lengths in VGTT feature can be enabled.

The TOBR feature must be turned on before any of the TOBR Quantity features can be enabled.

A TOBR quantity feature cannot be enabled if a TOBR feature with a higher quantity is enabled.

If the TOBR quantity feature of maximum quantity level is enabled, then no other TOBR Quantity feature can be enabled.

The Prepaid IDP Query Relay feature must be turned on before the following features can be enabled:

  • IDP A-Party Blacklist
  • IDP A-Party Routing
  • IDP Service Key Routing

The INP feature must be turned on before the INP CRP feature can be enabled.

The Default Country Code must be provisioned (see the defcc parameter in the chg-stpopts command) before the ATINP, IAR Base, MT-Based GSM SMS NP, or MT-Based IS41 SMS NP feature can be enabled.

If the system contains any cards other than those listed below, then the 2800 links quantity of the Large System # Links feature cannot be enabled:

  • E5-ATM-B
  • E5-E1T1-B
  • E5-ENET-B
  • E5-IPSM
  • E5-MCPM-B
  • E5-OAM
  • E5-SM4G
  • E5-SM8G-B
  • E5-TSM
  • HIPR2 

The Info Analyzed Relay Base (IAR Base) feature must be enabled before the IAR NP, IAR GRN, or IAR ASD feature can be enabled.

The S-Port feature and the IDP A-Party Blacklist feature cannot both be enabled in the system.

The value specified for the partnum parameter must consist of 9 digits, without any dashes. The first three digits are 893. The next six values are numeric (0...9).

The Service Portability (S-Port) feature must be enabled before the S-Port Subscriber Differentiation feature can be enabled.

If the system is not in mixed mode and is equipped with GPSM-II/TDM card(s), then the Integrated GLS and Integrated Measurements features cannot be enabled.

The A-Port or IGM feature must be turned on before the LOCREQ Query Response feature can be enabled.

If a PCT feature of maximum quantity level is enabled, then a PCT feature of a lower quantity cannot be enabled.

A PCT feature cannot be enabled if the quantity is higher than the quantity of the associated FAK.

If a DSM card is provisioned in the system, then the FLOBR, GTT Action – DUPLICATE, and VGTT-16 features cannot be enabled.

If an EOAM card is in the active or standby MASP location, then the 10,000 Routesets feature cannot be enabled.

The VCI value for any ATM link (see the ent-slk command) must be less than or equal to 16383 before a 3 Links per Card feature quantity can be enabled.

The mtplprst option must be configured (see the chg-stpopts command) before the Origin-based MTP Routing feature can be enabled.

The matchseq=dn parameter must be specified (see the chg-tifopts command) before the TIF Number Substitution feature can be enabled.

Each provisioned Service Module card must have at least 4G memory before the AINPQ feature can be enabled.

At least one EPAP related feature must be turned on before the EPAP Data Split feature can be enabled.

The EPAP Data Split feature requires E5-SM4G or E5-SM8G-B cards.

ISUP NP with EPAP feature cannot be enabled once Dual ExAP Config feature has been enabled.

TIF Selective Screening feature is mutually exclusive with TIF Number Substitution feature. TIF Selective Screening feature uses Number Substitution digit field to store Call Types associated with DN.

The Default Country Code must be provisioned (see the defcc parameter in the chg-stpopts command) before the SIP NP feature can be enabled.

The J7 support feature cannot be enabled if ANSI or ITUN-24 SID is already provisioned.

The EPM A/E5-SM4G cards are not supported when the SMxG 13,600 TPS Throughput Capacity feature is enabled.

Notes

XGTT or XMAP (GTT or MAP Table Increase) Feature

After the XGTT feature is enabled, the feature cannot be disabled or turned off.

After the XMAP feature is enabled, the feature cannot be disabled or turned off.

1500 Links and 2000 Links Support

After the 1500 Links feature or the 2000 Links Support feature is enabled, the feature cannot be disabled or turned off.

SE-HSL SLK Capacity

The SE-HSL feature allows unchannelized E1 links to be provisioned. The maximum number of unchannelized signaling links that can be assigned to E5-E1T1-B cards in the system with each SE-HSL SLK Capacity quantity feature access key are:

  • 893-0130-01—4
  • 893-0130-02—8
  • 893-0130-03—16
  • 893-0130-04—24
  • 893-0130-05—32
  • 893-0130-06—40
  • 893-0130-07—48
  • 893-0130-08—56
  • 893-0130-09—64
  • 893-0130-10—72
  • 893-0130-11—80
  • 893-0130-12—88
  • 893-0130-13—96
  • 893-0130-14—104
  • 893-0130-15—112
  • 893-0130-16—120

LNP Ported Numbers Capacity, LNP NPANXXs, LNP LRNs, and LNP ELAP Configuration Features

Table 4-21 lists the minimum Service Module hardware type required by each LNP quantity feature. Quantities of 204-228 million TNs require DSM cards and do not support E5-SM4G or E5-SM8G-B cards. Quantities of 240-504 million TNs require E5-SM4G or E5-SM8G-B cards.

Quantities of 516-756 million TNs require SLIC cards.

Table 4-21 Minimum Hardware Required for LNP Quantity Features

Object / Capacity Minimum Hardware Part Number

156 Million TNs

4 GB Service Module card

893-0110-17

168 Million TNs

4 GB Service Module card

893-0110-18

180 Million TNs

4 GB Service Module card

893-0110-19

192 Million TNs

4 GB Service Module card

893-0110-20

204 Million TNs

This capacity was previously supported only on the 4 GB DSM card. Starting with EAGLE Release 46.0, the DSM card is no longer supported; therefore this specific capacity limit is no longer supported.

893-0110-21

216 Million TNs

This capacity was previously supported only on the 4 GB DSM card. Starting with EAGLE Release 46.0, the DSM card is no longer supported; therefore this specific capacity limit is no longer supported.

893-0110-22

228 Million TNs

This capacity was previously supported only on the 4 GB DSM card. Starting with EAGLE Release 46.0, the DSM card is no longer supported; therefore this specific capacity limit is no longer supported.

893-0110-23

240 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-24

252 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-25

264 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-26

276 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-27

288 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-28

300 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-29

312 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-30

324 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-31

336 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-32

348 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-33

360 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-34

372 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-35

384 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-36

396 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-37

408 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-38

420 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-39

432 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-40

444 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-41

456 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-42

468 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-43

480 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-44

492 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-45

504 Million TNs

E5-SM4G/E5-SM8G-B

893-0110-46

516 Million TNs SLIC 893011047
528 Million TNs SLIC 893011048
540 Million TNs SLIC 893011049
552 Million TNs SLIC 893011050
564 Million TNs SLIC 893011051
576 Million TNs SLIC 893011052
588 Million TNs SLIC 893011053
600 Million TNs SLIC 893011054
612 Million TNs SLIC 893011055
624 Million TNs SLIC 893011056
636 Million TNs SLIC 893011057
648 Million TNs SLIC 893011058
660 Million TNs SLIC 893011059
672 Million TNs SLIC 893011060
684 Million TNs SLIC 893011061
696 Million TNs SLIC 893011062
708 Million TNs SLIC 893011063
720 Million TNs SLIC 893011064
732 Million TNs SLIC 893011065
744 Million TNs SLIC 893011066
756 Million TNs SLIC 893011067

150,000 NPANXXs

4 GB Service Module card

893-0094-01

300,000 NPANXXs

4 GB Service Module card

893-0094-02

100,000 LRNs

4 GB Service Module card

893-0105-05

150,000 LRNs

4 GB Service Module card

893-0105-01

Flexible GTT Load Sharing

The Flexible GTT Load Sharing feature allows a PC or PC/SSN combination to be provisioned in multiple load-sharing relationships for post-GTT load sharing of intermediate and final GTT traffic.

Load sharing for intermediate GTT traffic requires the Intermediate GTT Load Sharing feature, which can be run in conjunction with the Flexible GTT Load Sharing feature. Intermediate GTT load sharing is performed through the MRN table, and the GTT destination is a PC. If both the Intermediate and Flexible GTT Load Sharing features are on, different load-sharing relationships can be defined between the same set of PCs, and different sets of destinations can contain the same PCs.

Load sharing for final GTT traffic is performed through the MAP table, and the GTT destination is a PC/SSN combination. If the Flexible GTT Load Sharing feature is on, different load-sharing relationships can be defined between the same set of PC/SSNs, and different sets of destinations can contain the same PC/SSN combinations.

Weighted GTT Loadsharing

The Weighted GTT Loadsharing feature allows a PC or PC/SSN combination to be provisioned with weights and threshold values to change the loadsharing method. This weight is relative to the weights of the PCs or PC/SSNs that have the same relative cost (RC group) and determines the relative percentage of traffic sent to the PC or PC/SSN. If the total available weight of the PCs or PC/SSNs in the RC group falls below the threshold, that RC group is not used and the next lowest RC group is used for traffic loadsharing.

SEAS Over IP

All database commands associated with the SEAS Over IP feature can be entered after the SEAS Over IP feature is enabled.

SCCP Loop Detection

The SCCP Loop Detection feature allows sets of point codes that form a routing loop in the network to be specified. These sets are linked with GTT sets and are checked during intermediate and final GTT traffic routing. If a loop exists, either the system can simply be notified or the traffic can be discarded. The SCCP Loop Detection feature requires the GTT feature and is supported on Service Module cards.

Multiple Linksets to a Single Adjacent PC (MLS)

The MLS feature allows multiple linksets to be established to a single adjacent destination point code.

Voice Mail Router (V-Flex)

The V-Flex feature allows calls to be routed to a specific voice mail server based on subscriber and call context data.

Proxy Point Code Capacity

The Proxy Point Code feature allows the EAGLE to assume the point codes of other nodes. The total numbers of proxy point codes that can be provisioned in the system for each quantity are:

  • 893-0187-01—10
  • 893-0187-02—20
  • 893-0187-03—30
  • 893-0187-04—40
  • 893-0187-05—50
  • 893-0187-06—60
  • 893-0187-07—70
  • 893-0187-08—80
  • 893-0187-09—90
  • 893-0187-10—100

E5-SM4G and E5-SM8G-B Throughput Capacity

The E5-SM4G and E5-SM8G-B Throughput Capacity feature is a quantity feature that is used to increase the SCCP traffic processing capacity of an E5-SM4G or E5-SM8G-B card.

  • 893-0191-01—5000 TPS
  • 893-0191-02—6800 TPS
  • 893-0191-03—10,000 TPS
  • 893-0191-04—13,600 TPS

Table 4-22 displays the TPS capacities for each E5-SM4G Throughput Capacity Quantity

Table 4-22 TPS Capacities

Feature Quantity Part Number Maximum TPS Capacity per Card Maximum System TPS Capacity*
893-0191-01 3125 (if one or more EPAP-based features are enabled)

75,000 TPS with one or more EPAP-based features and 24+1cards

96,875 TPS with one or more EPAP-based features and 31+1 cards

5000 (if no EPAP-based features are enabled)

155,000 TPS (if one or more GTT-based features is turned on) and 31+1 cards

40,000 TPS (if one or more ELAP-based features is enabled) with 8+1 cards

85,000 TPS (if one or more ELAP-based features is enabled) with 17+1 cards

893-0191-02 6800

210,800 TPS with or without EPAP-based features and 31+1 cards

163,200 TPS with one or more EPAP-based features and 24+1 cards

54,400 TPS with ELAP and 8+1 cards

115,600 TPS with ELAP and 17+1 cards

893-0191-03** 10,000

310,000 TPS with or without EPAP-based features and 31+1 cards

240,000 TPS with one or more EPAP-related features and 24+1 cards

80,000 TPS with ELAP and 8+1 cards

170,000 TPS with ELAP and 17+1 cards

893-0191-04** *** 13,600

421,600 TPS with or without EPAP-based features and 31+1 cards

326,400 TPS with one or more EPAP-related features and 24+1 cards

108,800 TPS with ELAP and 8+1 cards

231,200 TPS with ELAP and 17+1 cards

*32 cards implies an N+1 configuration, so 31 cards are used for calculating actual TPS capacity.

** Requires E5-SM8G-B

*** Requires B cards (E5-E1T1-B is recommended) or SLIC cards throughout a node.

HIPR2

The HIPR2 High Rate Mode feature (Part Number 893-0201-01) must be enabled before the EAGLE can use the entire channel for data and provide a throughput rate of 2.5Gbps. If this feature is not enabled, then the EAGLE provides an effective inter-shelf throughput rate of 1Gbps.

Advanced GT Modification (AMGTT)

There are three AMGTT features: 

  • Part number 893-0218-01: Advanced Global Title Modification (AMGTT). Allows non-MGTT customers to enable CdPA and CgPA functions after upgrade.
  • Part number 893-0218-02: Advanced Global Title Modification, Called Party Only (AMGTT CdPA Only). Allows existing MGTT customers to continue using CdPA modification functions after upgrade. Does not allow any CgPA modification capabilities. The AMGTT CdPA Only feature cannot be enabled by this command. It is automatically enabled upon upgrading from the source release to EAGLE release 38.0 if the MGTT feature was turned on prior to the upgrade.
  • Part number 893-0218-03: Advanced Global Title Modification, Calling Party Upgrade (AMGTT CgPA Upgrade). Allows existing MGTT customers to upgrade to AMGTT after upgrade to EAGLE release 38.0. Requires the AMGTT CdPA Only feature to be enabled, and allows full AMGTT CdPA and CgPA modification.

Prepaid IDP Query Relay

The IDPRCDPN(X) NPP Service must be turned on before the Prepaid IDP Query Relay feature can be turned on. The IDPRCGPN NPP service must be turned on to process Calling Party Numbers. The IDPRCGPN Service is reached from the IDPRCDPN Service. The following warning message appears while enabling the Prepaid IDP Query Relay feature:

Caution:

Any of the IDPRCDPN(X) NPP services must be ON before turning ON the IDPR feature.

MO SMS IS41-to-GSM Migration

The MO SMS IS41-to-GSM Migration feature addresses modifications to the MO-based IS41 SMS NP feature (893-0194-01) required to meet certain IS41-to-GSM Migration call flows. This feature also allows the IS412GSM Migration Prefix to be used as a prefix instead of the RTDB RN/SP when an SMS is destined for a GSM-migrated subscriber.

SLS Bit Rotation by Incoming Linkset (ISLSBR)

The ISLSBR feature allows SLS Bit rotation to occur on an incoming linkset. This feature provides the ability to configure distribution in an ANSI or ITU network.

Eagle Additional Subscriber Data

Prepaid IDP Query Relay and TIF framework features support ASD data, which can be associated with individual subscribers and ranges. IDPR and TIF ASD/GRN features address the addition of ASD fields into the EAGLE. The ASD feature allows generic data to be associated with DN and DN Block subscriber records.

Prepaid SMS Intercept Ph1

The MOSMSGCDPN and MOSMSGCGPN services must be provisioned before the MO SMS Prepaid Check feature is turned on for "Prepaid SMS Intercept Ph1" to be functional. The following warning message appears while enabling the MO SMS Prepaid Check feature: 

Caution:

 MOSMSGCDPN or/and MOSMSGCGPN NPP Services must be turned on for the feature to be functional.

MO-based IS41 SMS NP and MO SMS IS41-to-GSM Migration

The MOSMSICDPN NPP service must be provisioned before the MO-based IS41 SMS NP or the MO SMS IS41-to-GSM Migration feature is turned on for the feature to be functional. The following warning message appears while enabling these features:

Caution:

MOSMSICDPN NPP Services must be turned on for the feature to be functional.

Portability Check for MO SMS

The MOSMSGCGPN NPP service must be enabled before the Portability Check for MO SMS feature is turned on for the feature to be functional. The following warning message appears while enabling the feature:

Caution:

 MOSMSGCGPN NPP Services must be turned on for the feature to be functional.

MO-based GSM SMS NP

The MOSMSGCDPN NPP service must be provisioned before the MO-based GSM SMS NP feature is turned on for the feature to be functional. The following warning message appears while enabling the feature:

Caution:

 MOSMSGCDPN NPP Services must be turned on for the feature to be functional.

GTT Load Sharing With Alternate Routing Indicator

The GTT Load Sharing with Alternate Routing Indicator (GTT LS ARI) feature allows loadsharing relationships to be established between the MAP and MRN table in that the MAP and MRN sets allow provisioning of MRN and MAP sets, respectively, as the Alternate Mate RI if the point codes in the MAP or MRN table are unavailable.

ST-HSL-A SLK Capacity

The ST-HSL-A feature allows unchannelized T1 links to be provisioned. The total number of unchannelized signaling links that can be assigned to E5-E1T1-B cards in the system with each ST-HSL-A SLK Capacity quantity feature access key is enabled are:

  • 893-0273-01—4
  • 893-0273-02—8
  • 893-0273-03—16
  • 893-0273-04—24
  • 893-0273-05—32
  • 893-0273-06—40
  • 893-0273-07—48
  • 893-0273-08—56
  • 893-0273-09—64
  • 893-0273-10—72
  • 893-0273-11—80
  • 893-0273-12—88
  • 893-0273-13—96
  • 893-0273-14—104
  • 893-0273-15—112
  • 893-0273-16—120
  • 893-0273-07—128
  • 893-0273-18—136
  • 893-0273-19—144
  • 893-0273-20—152
  • 893-0273-21—160
  • 893-0273-22—168
  • 893-0273-23—176
  • 893-0273-24—180

MO SMS ASD, MO SMS GRN

The MOSMSGCGPN, MOSMSGCDPN, MOSMSICGPN, or MOSMSICDPN NPP service must be provisioned before the MO SMS ASD or MO SMS GRN feature is turned on for the feature to be functional. The following warning message appears while enabling the feature:

Caution:

MOSMSGCDPN, MOSMSICDPN, MOSMSGCGPN or/and MOSMSICGPN NPP Services must be turned on for the feature to be functional.

Large MSU Support for IP Signaling

The Large MSU Support for IP Signaling feature supports MSUs having a Service Information Field (SIF) up to 4095 bytes over M2PA and M3UA Protocols with Service Indicator (SI) values ranging from 6 to 15. The values for the Service Indicators are: 

  • 6, 7—Data
  • 9—Broadband ISDN
  • 10—Satellite ISDN
  • 13—BICC
  • 14—H.248 
  • 8, 11, 12, 15—Spare

EPAP based features

If Global Title Translation (GTT) is on and more than 25 SCCP cards are provisioned, then when the first EPAP based feature is enabled, a warning is issued to state that the EAGLE must be connected to an EPAP T1200 or higher. Subsequent commands for enabling EPAP based features are accepted without any warning. 

XUDT UDT Conversion feature

The XUDT UDT Conversion feature allows the following SCCP message conversions:

  • UDT(S) messages to XUDT(S) messages
  • Non-segmented XUDT(S) messages to UDT(S) messages
  •  Segmented XUDT(S) messages to UDT(S) messages

MTT 3354 deleted for PR 165345 MB

3 Links per Card feature

The 3 Links per Card feature is a quantity feature that supports a third link (A1) on an E5-ATM-B card. Each quantity FAK supports the 3 Links per card feature in an increment of 5 cards, up to a maximum of 385 cards. Part numbers range from 893-0391-01 (supports the feature on 5 cards) to 893-0391-77 (supports the feature on 385 cards).

Point Code and CIC Translation (PCT)

The PCT feature is a quantity feature that allows the EAGLE to change the destination point code (DPC) and originating point code (OPC) of an MTP-routed MSU to previously configured values. The quantity is used to define the maximum number of allowed translations:

  • 893-0372-01—25 translations
  • 893-0372-02—50 translations
  • 893-0372-03—75 translations
  • 893-0372-04—100 translations
  • 893-0372-05—150 translations
  • 893-0372-06—200 translations
  • 893-0372-07—250 translations
  • 893-0372-08—1000 translations

Integrated GLS

The E5-OAM Integrated GLS (Integrated GLS) feature allows the E5-MASP cards to support the function of GLS cards for Gateway Screening. If the Integrated GLS feature is turned on, then the E5-MASP accepts the bind requests for the GWS screenset from network cards, binds the requested screenset, and downloads the screenset to the requested network cards.

If the Integrated GLS feature is turned OFF, then the E5-MASP cards do not service the requests for binding screensets and the network cards continue to send binding requests for screen sets to the active GLS cards.

E5-ENET-B IPSG High Throughput

The E5-ENET-B IPSG High Throughput feature allows the E5-ENET-B card running the IPSG application to have a maximum capacity of 9500 TPS. If the feature is not turned on, then the E5-ENET-B card running the IPSG application has a maximum capacity of 6500 TPS.

EPAP Data Split

The EPAP Data Split feature allows EPAP data to be split into DN and IMSI subsets. Each subset is loaded on a specific set of E5-SM4G or E5-SM8G-B cards. The maximum capacity for each data subset (120 million) can be loaded on the associated set of cards. Therefore, splitting the data allows a system-wide EPAP data capacity of 240 million.

Dual ExAP Config

Warning: Enabling the Dual ExAP Config feature will disable functions of ISUP NP with EPAP and TINP.

Prior to enabling the Dual ExAP Config feature, upgrade the ISUP NP with EPAP and TINP features to TIF if one or both of those features are present in the system.

The Dual ExAP Config feature is allowed to be turned on regardless of whether the ISUP NP with EPAP or TINP features are already turned on.

If the Dual ExAP Config is turned on while ISUP NP with EPAP and TINP are not upgraded to TIF, these two features will stop working.

SIP Number Portability

The SIP-based Number Portability feature allows the E5-SM8G-B card running the SIPHC application to support SIP interfaces on EAGLE and also provide SIP based Number Portability using EAGLE's RTDB/RIDB.

1M System TPS

The 1M System TPS feature allows provisioning 1,000,000 TPS on SIGTRAN and ATM cards collectively. If the feature is not turned on, then the system will support 750,000 TPS or 500,000 TPS only based on the state of HIPR2 High Rate Mode feature. If the HIPR2 High Rate Mode feature is ON and the 1M System TPS is OFF, the system will support 750,000 TPS. If the HIPR2 High Rate Mode feature is OFF and the 1M System TPS is OFF, the system will support 500,000 TPS. HIPR2 High Rate Mode feature is a mandatory feature for turning ON the 1M System TPS feature.

S13/S13' Interface for EIR

The Diameter S13/S13' Interface for EIR feature allows the E5-SM8G-B card running the DEIRHC application to support Diameter S13/S13' interface on EAGLE and also provide EIR functionality on 3G and LTE networks.

Output

enable-ctrl-feat:partnum=893xxxxxx

    tekelecstp 08-12-04 13:55:19 EST  EAGLE 46.3.0
    enable-ctrl-feat:partnum=893xxxxxx
    Command entered at terminal #4.
    ENABLE-CTRL-FEAT: MASP A - COMPLTD 
;

This example shows the output when more than 25 SCCP cards are provisioned and first EPAP-based feature is enabled:

This warning is issued when the first and only the first EPAP based feature is enabled.

enable-ctrl-feat:partnum=89xxxxxxx

    tekelecstp 10-02-26 15:40:56 EST  EAGLE 46.3.0
    enable-ctrl-feat:partnum=893xxxxxx
    Command entered at terminal #4.

    Warning: The Eagle must be connected to an EPAP T1200 or higher
    ENABLE-CTRL-FEAT: MASP A - COMPLTD 
;

Related Topics