4.580 rtrv-slk
Use this command to show the parameters for low-speed signaling links, ATM high-speed signaling links, or both.
Parameters
- aname (optional)
- Association name. The name of the association assigned to the links to be displayed.
- link (optional)
- The signaling link on the card specified in the loc parameter. The links can be specified in any sequence or pattern.
- Synonym:
- port
- Range:
- a, b, a1 - a63, b1 - b63
Not all card types support all link parameter values.
See Table A-1 for valid link parameter range values for each type of card that can have assigned signaling links.
- Default:
- Display all
- loc (optional)
- The card location as stenciled on the shelf of the system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
- Default:
- All signaling links are shown.
- type (optional)
- Link type. This parameter specifies to display a sub-set of links.
- Range:
-
- e1
- Display signaling links for E1 cards. Includes low speed E1 and SE-HSL links.
- ipgw
- Display signaling links configured for IPGW linksets
- ipsg
- Display signaling links configured for IPSG linksets
- j1
- Display signaling links for J1 cards. Includes low speed J1 links.
- mtp2
- Display low-speed signaling links
- saal
- Display ATM high-speed signaling links
- t1
- Display signaling links for T1 cards. Includes low speed T1 and ST-HSL-A links.
- Default:
- Display all signaling links
Example
rtrv-slk:loc=1302:link=a
rtrv-slk:loc=1302:link=b2
rtrv-slk:loc=1303:link=a31
rtrv-slk:aname=asocm2pa
rtrv-slk:loc=1305
rtrv-slk:type=j1
Dependencies
If the link parameter is specified, the loc parameter must be specified. The loc parameter can be specified without the link parameter.
The loc parameter or the class parameter, but not both, can be specified in the command.
The slot portion of the specified loc parameter must be 01 - 18, except 09 and 10 cannot be specified (loc=xyss, where x is the frame, y is the shelf, and ss is the slot).
Card locations 1113 - 1118 cannot be specified for the loc parameter.
The LIMATM, LIME1ATM, LIME1, LIMT1, DCM, and ENET/ENETB card types are the only valid card types for this command.
The card must be an E5-ATM-B, E5-E1T1-B, E5-ENET-B.
The specified card location must be equipped.
The IMT (Card) table must be accessible.
The Link table must be accessible.
The Linkset table must be accessible.
If an E5-ATM-B card is used, then a value of A, B, or A1 must be specified for the link parameter. A 3 Links per Card feature quantity must be enabled before the link=a1 parameter can be specified.
Notes
This command can be canceled using the F9 function key or the canc-cmd
command. See canc-cmd
for more information.
Not every card location represents a signaling link. Be sure to address a signaling link in this command.
The Installation Guide provides an illustration of the card locations.
Output
rtrv-slk
tekelecstp 09-12-17 13:54:32 EST EAGLE 42.0.0
rtrv-slk
Command entered at terminal #4.
LP ATM
LOC LINK LSN SLC TYPE SET BPS TSEL VCI VPI LL
1208 A e3e4 4 LIMATM 1 1.544M LINE 5 0 0
1218 A e3e4 5 LIMATM 1 1.544M LINE 5 0 0
LOC LINK LSN SLC TYPE ANAME SLKTPS
1303 A m2pa12132 0 IPSG m2pa1303a 1000
1303 B m3ua333a 0 IPSG m3ua1303b 500
1303 A1 m3ua323a 0 IPSG m3ua1303a 1000
1303 B1 m3ua333i 0 IPSG m3ua1303b 500
1303 B2 m3ua333n 0 IPSG m3ua1303b 500
1305 A ls1305a 0 IPSG sg1305a 1000
1305 B ls1305i 0 IPSG sg1305i 500
1305 A1 ls1305a 1 IPSG a1 1000
1305 B1 ls1305i 1 IPSG a1 500
1305 B14 lsitunbb 0 IPSG a1 1000
1305 B15 lsitunaa 0 IPSG a1 1000
LOC LINK LSN SLC TYPE
1313 A e3e4i 0 IPLIMI
LOC LINK LSN SLC TYPE
1307 A ls1307a 0 SS7IPGW
1315 A ls1315a 0 SS7IPGW
1317 A ls1317i 0 IPGWI
SLK table is (20 of 1200) 2% full.
;
This example shows the link information for an LIMATM card:
rtrv-slk:loc=1304:link=a
tekelecstp 09-12-14 12:17:00 EST EAGLE 42.0.0
LP ATM
LOC LINK LSN SLC TYPE SET BPS TSEL VCI VPI LL
1304 A ls1 3 LIMATM 1 1.544M LINE 5 0 0
This example shows the link information for an IPSG card:
rtrv-slk:loc=1301
e1001501 10-04-03 16:20:45 EST EAGLE 42.0.0
LOC LINK LSN SLC TYPE ANAME SLKTPS/ MAXSLKTPS
RSVDSLKTPS
1301 A SCS1 0 IPSG sg1301a 500 5000
1301 B SCS2 0 IPSG sg1301b 1000 5000
1301 A1 MGC1 0 ISPG sg1301a1 700 5000
1301 B1 MGC2 0 IPSG sg1301b1 1200 5000
IPTPS for LOC = 1301 is (3400 of 5000) 68%
;
This example shows link information for signaling links configured for a specified association:
rtrv-slk:aname=m3ua1211a1
e1001501 10-04-03 16:20:45 EST EAGLE 42.0.0
LOC LINK LSN SLC TYPE ANAME SLKTPS/ MAXSLKTPS
RSVDSLKTPS
1211 A1 ls1211b 0 IPSG m3ua1211a1 600 5000
1211 A2 ls1211c 0 IPSG m3ua1211a1 700 5000
;
This example shows the link information for an E5-ATM-B card:
rtrv-slk:loc=1305
tekelecstp 11-03-14 12:17:00 EST EAGLE 44.0.0
LP ATM
LOC LINK LSN SLC TYPE SET BPS TSEL VCI VPI LL
1305 A ls1 0 LIMATM 1 1.544M LINE 5 0 0
1305 B ls1 1 LIMATM 1 1.544M LINE 5 0 0
This example shows the link B information for an E5-ATM-B card:
rtrv-slk:loc=1305:link=b
tekelecstp 11-03-14 12:17:00 EST EAGLE 44.0.0
LP ATM
LOC LINK LSN SLC TYPE SET BPS TSEL VCI VPI LL
1305 B ls1 1 LIMATM 1 1.544M LINE 5 0 0
This example shows ATM (ANSI & ITU) and E1/T1 (HSL & LSL) links:
rtrv-slk
tekelecstp 09-12-17 17:09:54 EST 42.0.0
LP ATM
LOC LINK LSN SLC TYPE SET BPS TSEL VCI VPI LL
1101 A ls333 0 LIMATM 1 1.544M LINE 5 0 0
LP ATM E1ATM
LOC LINK LSN SLC TYPE SET BPS TSEL VCI VPI CRC4 SI SN
1201 A lsi333 1 LIME1ATM 21 2.048M EXTERNAL 5 0 ON 3 0
L2T PCR PCR E1 E1
LOC LINK LSN SLC TYPE SET BPS ECM N1 N2 LOC PORT TS
1204 A lsi111 0 LIME1 26 1.984M BASIC ---- ------ 1204 5 1
1205 A1 lsi222 0 LIME1 11 56000 BASIC ---- ------ 1205 1 3
L2T PCR PCR T1 T1
LOC LINK LSN SLC TYPE SET BPS ECM N1 N2 LOC PORT TS
1104 A ls111 0 LIMT1 31 1.536M BASIC ---- ------ 1104 5 1
1105 A1 ls222 0 LIMT1 1 56000 BASIC ---- ------ 1105 1 2
SLK table is (6 of 1200) 1% full.
;
This example shows link A1 information for an E5-ATM-B card:
rtrv-slk:loc=1306:link=a1
tekelecstp 11-03-18 12:17:00 EST EAGLE 44.0.0
LP ATM
LOC LINK LSN SLC TYPE SET BPS TSEL VCI VPI LL
1306 A1 ls1 1 LIMATM 1 1.544M LINE 5 0 0
This example shows link information for an E5-ENET-B card:
rtrv-slk:loc=1301
tekelecstp 11-03-14 16:22:25 EST EAGLE5 44.0.0
LOC LINK LSN SLC TYPE ANAME SLKTPS/ MAXSLKTPS
RSVDSLKTPS
1301 A SCS1 0 IPSG sg1301a 500 6500
1301 B SCS2 0 IPSG sg1301b 1000 6500
1301 A1 MGC1 0 ISPG sg1301a1 700 6500
1301 B1 MGC2 0 IPSG sg1301b1 1200 6500
RSVDSLKTPS for LOC = 1301 is (3400 of 6500) 52%.
SLK table is (4 of 1200) 1% full.
This example shows link information for a J1 link:
rtrv-slk:type=j1
tekelecstp 13-12-19 19:02:51 EST 46.0.0-65.3.0
rtrv-slk:type=j1
Command entered at terminal #4.
L2T PCR PCR J1
LOC LINK LSN SLC TYPE SET BPS ECM N1 N2 PORT TS
1102 A ls2 11 LIMT1 11 64000 BASIC ---- ------ 1 11
1102 A1 ls2 10 LIMT1 11 64000 BASIC ---- ------ 1 11
1102 A2 ls2 5 LIMT1 11 64000 BASIC ---- ------ 1 25
SLK table is (7 of 1200) 1% full.
;
This example shows the link information for a SLIC card running the IPSG application:
rtrv-slk:loc=1301
e1001501 16-05-27 16:20:45 EST EAGLE 46.4.0
LOC LINK LSN SLC TYPE ANAME SLKTPS/ MAXSLKTPS
RSVDSLKTPS
1301 A30 SCS1 0 IPSG sg1301a 500 9500
1301 B35 SCS2 0 IPSG sg1301b 1000 9500
1301 A50 MGC1 0 ISPG sg1301a1 700 9500
1301 B55 MGC2 0 IPSG sg1301b1 1200 9500
IPTPS for LOC = 1301 is (3400 of 9500) 35%
;
Legend
- LOC—Location of the card containing the signaling link
- LINK—Signaling link assigned to the card
- LSN—Name of the linkset containing the signaling link
- SLC—Signaling link code of the signaling link
- TYPE—Type of card
- ANAME—Association name
- SLKTPS/RSVDSLKTPS—SLKTPS guaranteed for an IPSG link
- MAXSLKTPS—Maximum SLKTPS allowed for an IPSG link
- L2TSET—Number of the level 2 timer set associated with the signaling link
- BPS—Transmission rate of the signaling link in bits per second
- ECM—Basic of PC for transmission
- PCRN1—MSU number
- PCRN2—Octet number
- LPSET—ATM link parameter set identifier
- ATMTSEL—ATM timing selector. Possible values are as follows:
- Internal—Derived from an internal clock source operating at 1.544 MHz ± 200 Hz (ANSI) or 2.048 MHz ± 103 Hz (ITU).
- External—Derived from the High-Speed Master Clock (T1 or E1)
- Line—Derived from its received data stream, if present
- VCI—ATM virtual channel identifier
- VPI—ATM virtual path identifier
- LL—ATM line length
- E1PORT—E1 card port that has an E1 interface assigned to it.
- T1PORT—T1 card port that has a T1 interface assigned to it
- TS—Timeslot associated with the signaling link that is serviced by the E1 or T1 interface
- E1ATMCRC4—E1 ATM card CRC4 multi-frame structure enable/disable indicator
- E1ATMSI—Value of two Spare International bits of NFAS data for the E1 ATM card
- E1ATMSN—Value of five Spare National bits of NFAS data for the E1 ATM card
- J1PORT--- J1 card port that has a J1 interface assigned to it.