Making the Trial Utility GPL the Approved Utility GPL

This procedure is used to make the trial UTILITY generic program load (GPL) the approved UTILITY GPL.

The UTILITY GPL cannot be loaded and run from the removable cartridge like the other GPLs. The approved version of the UTILITY GPL is on the fixed disk. The trial version of the UTILITY GPL is located on the removable cartridge or removable media. This procedure loads the trial UTILITY GPL from the removable cartridge to the fixed disk and makes it the approved UTILITY GPL.

The removable cartridge or removable media that contains the UTILITY GPL to be loaded on to the EAGLE is required.

When the UTILITY GPL is displayed with the rtrv-gpl command, the entry CDU appears in the GPL column of the rtrv-gpl output.

1. Verify the control cards that are installed in the EAGLE.

   Refer to Maintenance and Administration Subsystem for information about the control cards.

2. Check the E5-MASPs for removable media.

   If removable media is installed in both E5-MASPs, continue the procedure with 4.

   If removable media is not installed in both E5-MASPs, continue the procedure with 3.

3. Verify the active MASP by entering the rept-stat-db command.

   This is an example of the possible output.

   rlghncxa03w 09-03-01 15:25:40 GMT  EAGLE5 40.1.0
   DATABASE STATUS: >> OK <<
           TDM 1114 ( STDBY)                 TDM 1116 ( ACTV )
           C   LEVEL    TIME LAST BACKUP     C   LEVEL    TIME LAST BACKUP
           - -------- ---------------------- - -------- ----------------------
   FD BKUP Y       36 09-02-19 09:38:25 GMT  Y       36 09-02-19 09:38:25 GMT
   FD CRNT Y       39                        Y       39
           MCAP 1113                         MCAP 1115
           - --------                        - --------
   RD BKUP -    -         -        -         Y       36 09-02-19 09:27:17 GMT
   USB BKP -    -         -        -         Y        3 09-02-07 01:11:22 GMT
   

   If removable media is installed in the active MASP, continue the procedure with 4.

   If removable media is not installed in the active MASP, insert the removable media in the removable media drive in the active MASP. For more information about inserting removable media in the removable media drive, refer to Removable USB Drive. After the removable media has been inserted in the removable media drive in the active MASP, continue the procedure with 4.

4. Display the UTILITY GPLs on the fixed disk and on the removable media using the rtrv-gpl:gpl=utility command.

   This is an example of the possible output.

   rlghncxa03w 09-03-01 07:01:08 GMT EAGLE5 40.1.0
   GPL Auditing  ON
   
   GPL       CARD  RELEASE      APPROVED         TRIAL        REMOVE TRIAL
   CDU       1114  162-000-000  162-000-000      162-001-000  162-001-000
   CDU       1116  162-000-000  162-000-000      162-001-000  162-001-000
   CDU       1115  -----------  -----------      -----------  -----------
   

   If the version of the UTILITY GPL shown in the REMOVE TRIAL column of the rtrv-gpl output is not the version that is to be loaded onto the cards, remove the removable media from the active MASP.

   Insert the removable media that contains the UTILITY GPL that is being updated into the removable media drive in the active MASP and repeat this step.

   For more information about inserting or removing removable media in the media drive, refer to Removable USB Drive.

   If the version of the UTILITY GPL shown in the REMOVE TRIAL column of the rtrv-gpl output is the version that is to be loaded onto the cards, continue the procedure with 5.

5. Change the GPLs, using the chg-gpl command and specifying the value for the trial UTILITY GPL shown in the output of the rtrv-gpl command used in 4.

   For this example, enter this command.

   chg-gpl:gpl=utility:ver=162-001-000

   This message should appear.

   rlghncxa03w 09-03-01 06:52:20 GMT EAGLE5 40.1.0
   GPL Auditing  ON
   
   UTILITY upload to 1114 completed
   UTILITY upload to 1116 completed
   System Release ID table upload 1114 completed
   System Release ID table upload 1116 completed
   

6. Display the UTILITY GPLs on the fixed disk and on the removable cartridge using the rtrv-gpl:gpl=utility command.

   This is an example of the possible output.

   rlghncxa03w 09-03-01 07:01:08 GMT EAGLE5 40.1.0
   GPL Auditing  ON
   
   GPL       CARD  RELEASE      APPROVED         TRIAL        REMOVE TRIAL
   CDU       1114  162-001-000  162-001-000      162-001-000  162-001-000
   CDU       1116  162-001-000  162-001-000      -----------  -----------
   

   This is an example of the possible output.

   rlghncxa03w 09-03-01 07:01:08 GMT EAGLE5 40.1.0
   GPL Auditing  ON
   
   GPL       CARD  RELEASE      APPROVED         TRIAL        REMOVE TRIAL
   CDU       1114  162-001-000  162-001-000      162-001-000  162-001-000
   CDU       1116  162-001-000  162-001-000      162-001-000  162-001-000
   CDU       1115  -----------  -----------      -----------  -----------
   

7. This procedure is finished.

Figure 3-6 Making the Trial Utility GPL the Approved Utility GPL

Sheet 1 of 3

Sheet 2 of 3

Sheet 3 of 3