特定のOracle Private Cloud Applianceリリースのすべてのソフトウェア・コンポーネントは、連携して動作するよう設計されています。 一般的なルールとして、個別のアプライアンス・コンポーネントはアップグレードしないでください。 1つ以上のコンポーネントのファームウェアのアップグレードが必要な場合、正しいバージョンは、My Oracle SupportからダウンロードしたOracle Private Cloud Appliance .iso
ファイル内に配布されます。 イメージ・ファイルが内部共有ストレージに解凍されると、このディレクトリに確認機能が配置されます: /nfs/shared_storage/mgmt_image/firmware/
。
ファームウェアのアップグレード時に、コンピュート・ノードのプロビジョニング操作を実行しないでください。
特定のサービスでは、コントローラ・ソフトウェアの更新後にハードウェア管理パックをアップグレードする必要があります。 詳細は、「Oracle Private Cloud Applianceリリース・ノート」の「一部のサービスではハードウェア管理パックのアップグレードが必要です」を参照してください。
Oracle Private Cloud Applianceハードウェア・コンポーネントのファームウェアをアップグレードする特定のまたは追加の手順が使用可能な場合は、このセクションに表示されます。 ここに記載されていないコンポーネントについては、サブコンポーネントの製品ドキュメントに記載されている手順に従ってください。 アプライアンス・コンポーネントのドキュメントの概要は、このマニュアルの「はじめに」およびOracle Private Cloud Applianceドキュメント・ライブラリの索引ページを参照してください。
Oracle Private Cloud Applianceのサポート可能性、信頼性およびセキュリティを高めるために、Oracleではコンポーネント・ファームウェアへの標準化されたアプローチを導入しています。 一般ルールは変更されません: コンポーネントとそれぞれのファームウェアは連携して動作するように設計されているため、個別にアップグレードすることはできません。 ただし、特定のコントローラ・ソフトウェア・リリースの.iso
ファイルの一部として提供されるファームウェア・アップグレードは、オプションでなくなりました。
ソフトウェア・リリースの前のテスト・プロセスの一環として、コンポーネント・ファームウェアの組合せが、該当するすべてのハードウェア・プラットフォームでテストされます。 これにより、Oracleでは、アプライアンスのファームウェアの完全認証セットをソフトウェア・リリースに対応した全体として配信できます。 認定状態でOracle Private Cloud Applianceを管理するために、特定のソフトウェア・リリースにアップグレードする顧客は、コントローラ・ソフトウェアの一部として配布されたすべての認証ファームウェアのアップグレードもインストールすることが期待されます。
特定のリリースのOracleで認証されているファームウェアのバージョンは、そのリリースの「Oracle Private Cloud Applianceリリース・ノート」にリストされています。 システム上で稼働しているOracle Private Cloud Appliance Controllerソフトウェアのリリースのリリース・ノートを参照し、「ファームウェアの評価」の章を開きてください。
次の手順で示すファイル名は、システムの.iso
イメージ内のファイル名と完全には一致しない場合があることに注意してください。
Oracleでは、セキュリティの脆弱性を排除するなど、多くの製品のファームウェア・パッチを定期的にリリースします。 重要なファームウェア・パッチが、通常のコントローラ・ソフトウェアのリリース・スケジュール外でOracle Private Cloud Applianceのコンポーネントにリリースされることがあります。 この問題が発生した場合、パッチは他のすべてのアプライアンス・ファームウェアと同じテストを実行しますが、これらは認証されたファームウェア・リストまたは影響を受けるコントローラ・ソフトウェア・リリースのインストール.iso
に追加されません。
徹底的なテストのあと、コントローラ・ソフトウェア.iso
イメージに含めることができない重要なファームウェア・パッチを、My Oracle Supportを介してOracle Private Cloud Applianceユーザーが使用できるようにします。
新しいOracle Private Cloud Appliance ControllerソフトウェアおよびOracle VMアップグレードとの互換性の問題を回避するため、現在のOracle Private Cloud Applianceソフトウェア・リリースのISOイメージに含まれるサーバーILOMファームウェアを常にインストールする必要があります。 ISOイメージがアプライアンスの内部ストレージにアンパックされている場合は、このロケーションの管理ノードからファームウェア・ディレクトリに到達できます: /nfs/shared_storage/mgmt_image/firmware/
。
ファームウェア・アップグレード手順については、アプライアンス・ラックに取り付けられているサーバー・シリーズの管理ガイドを参照してください。
このセクションの手順は、Oracle Private Cloud Applianceの一部として、コンポーネント・ファームウェアのアップグレードに固有です。
このプロシージャの実行中、管理ノード上のOracle Private Cloud Applianceサービスは一定期間停止する必要があります。 このアップグレードを慎重に計画して、コンピュート・ノードのプロビジョニング、Oracle Private Cloud Appliance構成の変更、またはOracle VM Managerの操作が同時に実行されないようにしてください。
8.7.20以降のバージョンへのファームウェアのアップグレードの場合、バージョン8.7.14への中間アップグレードが必要です。 これにより、バージョン8.7.14を目的の新しいバージョンにアップグレードできます。 詳細は、「Oracle Private Cloud Applianceリリース・ノート」の「Oracle ZFS Storage Appliance Firmwareのアップグレード8.7.20には2フェーズの手順が必要です」を参照してください。
ソフトウェア・アップグレードに関する詳細情報は、「Oracle ZFS Storage Appliance顧客サービス・マニュアル」 (ドキュメントID)にあります: F13771). " 「ソフトウェアのアップグレード」 "の項を参照してください。
Oracle Private Cloud Appliance内部ZFS Storage Applianceには、アクティブ/パッシブ構成の2つのクラスタ化コントローラが含まれています。 スタンドアロン・コントローラのアップグレード情報は無視できます。
ZFS Storage Applianceオペレーティング・ソフトウェアのアップグレード
ストレージ・コントローラでアップグレードを開始する前に、「Oracle ZFS Storage Appliance顧客サービス・マニュアル」の準備手順に従います。 " 「ソフトウェア・アップグレードの準備」 "のタイトルの項を参照してください。
SSHおよびスーパーユーザー権限を持つアカウントを使用して、マスター管理ノードにログオンします。
Oracle Private Cloud Applianceソフトウェア・イメージに含まれているファームウェア・パッケージを解凍します。
[root@ovcamn05r1 ~]# mkdir /nfs/shared_storage/yum/ak [root@ovcamn05r1 ~]# cd /nfs/shared_storage/yum/ak [root@ovcamn05r1 ak]# unzip /nfs/shared_storage/mgmt_image/firmware/storage/AK_NAS/p27357887_20131_Generic.zip Archive: /nfs/shared_storage/mgmt_image/firmware/storage/AK_NAS/p27357887_20131_Generic.zip extracting: ak-nas-2013.06.05.8.6-1.2.6.4214.1x-nondebug.pkg inflating: OS8.8.6_Readme.html
ソフトウェア更新パッケージを両方のストレージ・コントローラにダウンロードします。 管理IPアドレスは、192.168.4.1および192.168.4.2です。
SSHおよびスーパーユーザー権限のあるアカウントを使用してストレージ・コントローラの1つにログオンします。
[root@ovcamn05r1 ~]# ssh root@192.168.4.1 Password: ovcasn01r1:>
次の一連のコマンドを入力して、共有ストレージ・ディレクトリからコントローラにソフトウェア更新パッケージをダウンロードします。
ovcasn01r1:> maintenance system updates download ovcasn01r1:maintenance system updates download (uncommitted)> \ set url=http://192.168.4.100/shares/export/Yum/ak/ak-nas-2013.06.05.8.6-1.2.6.4214.1x-nondebug.pkg url = http://192.168.4.100/shares/export/Yum/ak/ak-nas-2013.06.05.8.6-1.2.6.4214.1x-nondebug.pkg.gz ovcasn01r1:maintenance system updates download (uncommitted)> set user=root user = root ovcasn01r1:maintenance system updates download (uncommitted)> set password Enter password: password = ******** ovcasn01r1:maintenance system updates download (uncommitted)> commit Transferred 157M of 484M (32.3%) ...
パッケージが完全にダウンロードされるまで待機し、展開してから次に進みます。
これらのステップを2つ目のストレージ・コントローラに対して繰り返します。
ストレージ・クラスタの構成を確認し、スタンバイ・コントローラにログオンしていることを確認します。
ovcasn02r1:> configuration cluster show Properties: state = AKCS_STRIPPED description = Ready (waiting for failback) peer_asn = 8a535bd2-160f-c93b-9575-d29d4c86cac5 peer_hostname = ovcasn01r1 peer_state = AKCS_OWNER peer_description = Active (takeover completed)
スタンバイ・コントローラのオペレーティング・ソフトウェア「第1」を常にアップグレードします。
使用可能なオペレーティング・ソフトウェアのバージョンを表示し、ダウンロードしたバージョンを選択します。
ovcasn02r1:> maintenance system updates ovcasn02r1:maintenance system updates> show Updates: UPDATE RELEASE DATE RELEASE NAME STATUS ak-nas@2013.06.05.8.3,1-1.1 2019-1-4 09:57:19 OS8.8.3 previous ak-nas@2013.06.05.8.5,1-1.3 2019-3-30 07:27:20 OS8.8.5 current ak-nas@2013.06.05.8.6,1-1.4 2019-6-21 20:56:45 OS8.8.6 waiting ovcasn02r1:maintenance system updates> select ak-nas@2013.06.05.8.6,1-1.4
選択したソフトウェア・バージョンでアップグレード・プロセスを起動します。
ovcasn02r1:maintenance system updates> upgrade This procedure will consume several minutes and requires a system reboot upon successful update, but can be aborted with [Control-C] at any time prior to reboot. A health check will validate system readiness before an update is attempted, and may also be executed independently using the check command. Are you sure? (Y/N) Y
アップグレードの最後に、コントローラが完全にリブートしてクラスタに再度参加するときは、再度ログインしてクラスタ構成を確認します。 アップグレードしたコントローラは、まだ準備完了(フェイルバックを待機中)状態である必要があります。
ovcasn02r1:> configuration cluster show Properties: state = AKCS_STRIPPED description = Ready (waiting for failback) peer_asn = 8a535bd2-160f-c93b-9575-d29d4c86cac5 peer_hostname = ovcasn01r1 peer_state = AKCS_OWNER peer_description = Active (takeover completed)
Oracle Private Cloud Applianceマスター管理ノードから、Oracle Private Cloud Applianceサービスを停止します。
注意このステップはスキップしないでください。 Oracle Private Cloud Applianceサービスの実行中にストレージ・コントローラのオペレーティング・ソフトウェアのアップグレードを実行すると、エラーと可能な停止時間が発生します。
[root@ovcamn05r1 ~]# service ovca stop
2番目のストレージ・コントローラでオペレーティング・システム・ソフトウェアをアップグレードします。
ストレージ・クラスタ構成を確認してください。 アクティブなコントローラにログオンしていることを確認します。
ovcasn01r1:> configuration cluster show Properties: state = AKCS_OWNER description = Active (takeover completed) peer_asn = 34e4292a-71ae-6ce1-e26c-cc38c2af9719 peer_hostname = ovcasn02r1 peer_state = AKCS_STRIPPED peer_description = Ready (waiting for failback)
使用可能なオペレーティング・ソフトウェアのバージョンを表示し、ダウンロードしたバージョンを選択します。
ovcasn01r1:> maintenance system updates ovcasn01r1:maintenance system updates> show Updates: UPDATE RELEASE DATE RELEASE NAME STATUS ak-nas@2013.06.05.8.3,1-1.1 2019-1-4 09:57:19 OS8.8.3 previous ak-nas@2013.06.05.8.5,1-1.3 2019-3-30 07:27:20 OS8.8.5 current ak-nas@2013.06.05.8.6,1-1.4 2019-6-21 20:56:45 OS8.8.6 waiting ovcasn01r1:maintenance system updates> select ak-nas@2013.06.05.8.6,1-1.4
選択したソフトウェア・バージョンでアップグレード・プロセスを起動します。
ovcasn01r1:maintenance system updates> upgrade This procedure will consume several minutes and requires a system reboot upon successful update, but can be aborted with [Control-C] at any time prior to reboot. A health check will validate system readiness before an update is attempted, and may also be executed independently using the check command. Are you sure? (Y/N) Y
アップグレードの最後に、コントローラが完全にリブートしてクラスタに再度参加するときは、再度ログインしてクラスタ構成を確認します。
ovcasn01r1:> configuration cluster show Properties: state = AKCS_STRIPPED description = Ready (waiting for failback) peer_asn = 34e4292a-71ae-6ce1-e26c-cc38c2af9719 peer_hostname = ovcasn02r1 peer_state = AKCS_OWNER peer_description = Active (takeover completed)
最後にアップグレードされたコントローラは、準備完了(フェイルバックを待機中)の状態である必要があります。 最初にアップグレードされたコントローラは、2番目のコントローラのアップグレードおよび再起動中にアクティブなロールを引き継ぎ、最初にアクティブなロールを保持しています。
両方のコントローラがアップグレードされたので、すべてのディスクがオンラインであることを確認します。
ovcasn01r1:> maintenance hardware show [...] NAME STATE MANUFACTURER MODEL SERIAL RPM TYPE chassis-000 1906NMQ803 ok Oracle Oracle Storage DE3-24C 1906NMQ803 7200 hdd disk-000 HDD 0 ok WDC W7214A520ORA014T 001851N3VKLT 9JG3VKLT 7200 data disk-001 HDD 1 ok WDC W7214A520ORA014T 001851N5K85T 9JG5K85T 7200 data disk-002 HDD 2 ok WDC W7214A520ORA014T 001851N5MPXT 9JG5MPXT 7200 data disk-003 HDD 3 ok WDC W7214A520ORA014T 001851N5L08T 9JG5L08T 7200 data disk-004 HDD 4 ok WDC W7214A520ORA014T 001851N42KNT 9JG42KNT 7200 data [...]
Oracle Private Cloud Appliance管理ノードのフェイルオーバーを開始し、すべてのサービスが別の管理ノードにリストアされるまで待機します。 これにより、Oracle VMとZFSストレージの間の接続の問題を回避できます。
SSHおよびスーパーユーザー権限を持つアカウントを使用して、マスター管理ノードにログオンします。
マスター管理ノードを再起動します。
[root@ovcamn05r1 ~]# pca-check-master NODE: 192.168.4.3 MASTER: True [root@ovcamn05r1 ~]# shutdown -r now
別の管理ノードにログオンし、必要なサービスが実行されるまで待機します。
注意プロンプトでこのコマンドを入力します: tail -f /var/log/messages。 管理ノードがマスター・ロールを引き継ぐときは、ログ・メッセージで示される必要があります。
サービスのステータスを確認します。
[root@ovcamn06r1 ~]# service ovca status Checking Oracle Fabric Manager: Running MySQL running (70254) [ OK ] Oracle VM Manager is running... Oracle VM Manager CLI is running... tinyproxy (pid 71315 71314 71313 71312 71310 71309 71308 71307 71306 71305 71301) is running... dhcpd (pid 71333) is running... snmptrapd (pid 71349) is running... log server (pid 6359) is running... remaster server (pid 6361) is running... http server (pid 71352) is running... taskmonitor server (pid 71356) is running... xmlrpc server (pid 71354) is running... nodestate server (pid 71358) is running... sync server (pid 71360) is running... monitor server (pid 71363) is running...
ストレージ・コントローラ・クラスタがアップグレードされている場合、解凍されたパッケージを使用可能にするために作成した共有ストレージ・ディレクトリを削除します。
# cd /nfs/shared_storage/yum/ak # ls ak-nas-2013.06.05.8.6-1.2.6.4214.1x-nondebug.pkg OS8.8.6_Readme.html # rm ak-nas-2013.06.05.8.6-1.2.6.4214.1x-nondebug.pkg OS8.8.6_Readme.html rm: remove regular file `ak-nas-2013.06.05.8.6-1.2.6.4214.1x-nondebug.pkg'? yes rm: remove regular file `OS8.8.6_Readme.html'? yes # cd .. # rmdir ak #
このセクションの手順は、Oracle Private Cloud Applianceの一部として、コンポーネント・ファームウェアのアップグレードに固有です。
Ciscoスイッチは、Ethernetベースのネットワーク・アーキテクチャを備えたシステムの一部です。
すべてのCiscoリーフ、スパイン・スイッチおよび管理スイッチのファームウェアのアップグレード
SSHおよびスーパーユーザー権限を持つアカウントを使用して、マスター管理ノードにログオンします。
アプライアンス共有ストレージで新しいCisco NX-OSファームウェア・イメージが使用可能であることを確認します。 コントローラ・ソフトウェアの更新時に、Oracle Private Cloud Applianceアップグレーダによってこのロケーションにファイルがコピーされます。
/nfs/shared_storage/mgmt_image/firmware/ethernet/Cisco/nxos.7.0.3.I7.7.bin
アップグレードするスイッチに管理者としてログオンします。
root@ovcamn05r1 ~]# ssh admin@ovcasw15r1 User Access Verification Password: ovcasw15r1#
スイッチを一度に1つずつ、次の順序でアップグレードしてください:
リーフのCisco Nexus 9336C-FX2スイッチ: ovcasw15r1, ovcasw16r1
Spine Cisco Nexus 9336C-FX2スイッチ: ovcasw22r1, ovcasw23r1
Management Cisco Nexus 9348GC-FXPスイッチ: ovcasw21r1
スイッチ上のブート・フラッシュのロケーションにファームウェア・ファイルをコピーします。
管理スイッチovcasw21r1でのコピー・コマンドは若干異なります。 適切なオプションを選択します。
リーフ・スイッチとスパイン・スイッチ:
ovcasw15r1# copy scp://root@192.168.4.216//nfs/shared_storage/mgmt_image/firmware/ethernet \ /Cisco/nxos.7.0.3.I7.7.bin bootflash:nxos.7.0.3.I7.7.bin vrf
management
root@192.168.4.216's password: nxos.7.0.3.I7.7.bin 100% 930MB 15.8MB/s 01:01 Copy complete, now saving to disk (please wait)... Copy complete.管理スイッチ:
ovcasw21r1# copy scp://root@192.168.4.216//nfs/shared_storage/mgmt_image/firmware/ethernet \ /Cisco/nxos.7.0.3.I7.7.bin bootflash:nxos.7.0.3.I7.7.bin vrf
default
root@192.168.4.216's password: nxos.7.0.3.I7.7.bin 100% 930MB 15.8MB/s 01:01 Copy complete, now saving to disk (please wait)... Copy complete.
現在実行中の構成を起動構成として保存します。
ovcasw15r1# copy running-config startup-config [########################################] 100% Copy complete, now saving to disk (please wait)... Copy complete.
bootFlashのロケーションにコピーされたCisco NX-OSソフトウェアをインストールします。 中断を伴うアップグレードに関するプロンプトが表示されたら、yを入力してインストールを続行します。
ovcasw15r1# install all nxos bootflash:nxos.7.0.3.I7.7.bin Installer will perform compatibility check first. Please wait. Installer is forced disruptive Verifying image bootflash:/nxos.7.0.3.I7.7.bin for boot variable "nxos". [####################] 100% -- SUCCESS Verifying image type. [####################] 100% -- SUCCESS Preparing "nxos" version info using image bootflash:/nxos.7.0.3.I7.7.bin. [####################] 100% -- SUCCESS Preparing "bios" version info using image bootflash:/nxos.7.0.3.I7.7.bin. [####################] 100% -- SUCCESS Performing module support checks. [####################] 100% -- SUCCESS Notifying services about system upgrade. [####################] 100% -- SUCCESS Compatibility check is done: Module bootable Impact Install-type Reason ------ -------- -------------- ------------ ------ 1 yes disruptive reset default upgrade is not hitless Images will be upgraded according to following table: Module Image Running-Version(pri:alt) New-Version Upg-Required ------ ---------- ---------------------------------------- -------------------- ------------ 1 nxos 7.0(3)I7(6) 7.0(3)I7(7) yes 1 bios v05.33(09/08/2018):v05.28(01/18/2018) v05.38(06/12/2019) yes Switch will be reloaded for disruptive upgrade. Do you want to continue with the installation (y/n)? [n] y Install is in progress, please wait. Performing runtime checks. [####################] 100% -- SUCCESS Setting boot variables. [####################] 100% -- SUCCESS Performing configuration copy. [####################] 100% -- SUCCESS Module 1: Refreshing compact flash and upgrading bios/loader/bootrom. Warning: please do not remove or power off the module at this time. [####################] 100% -- SUCCESS Finishing the upgrade, switch will reboot in 10 seconds.
正しいソフトウェア・バージョンがスイッチ上でアクティブになっていることを確認してください。
ovcasw15r1# show version Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Copyright (C) 2002-2019, Cisco and/or its affiliates. All rights reserved. [...] Software BIOS: version 05.38 NXOS: version 7.0(3)I7(7) BIOS compile time: 06/12/2019 NXOS image file is: bootflash:///nxos.7.0.3.I7.7.bin NXOS compile time: 8/28/2019 16:00:00 [08/29/2019 00:41:42] [...] ovcasw15r1#
VPCステータスを確認します。
注意このステップは、アプライアンスの内部管理ネットワーク・スイッチ(Cisco Nexus 9348GC-FXPスイッチ)には適用されません。 次のステップに進みます。
次に示すコマンドを使用します。 出力値はこの例と一致する必要があります。
ovcasw15r1# show vpc brief Legend: (*) - local vPC is down, forwarding via vPC peer-link vPC domain id : 2 Peer status : peer adjacency formed ok <---- verify this field vPC keep-alive status : peer is alive <----- verify this field Configuration consistency status : success <----- verify this field Per-vlan consistency status : success <----- verify this field Type-2 consistency status : success <----- verify this field vPC role : secondary Number of vPCs configured : 27 Peer Gateway : Enabled Dual-active excluded VLANs : - Graceful Consistency Check : Enabled Auto-recovery status : Disabled Delay-restore status : Timer is off.(timeout = 30s) Delay-restore SVI status : Timer is off.(timeout = 10s) Operational Layer3 Peer-router : Enabled
スイッチからログアウトします。 ファームウェアは正常にアップグレードされました。
アプライアンスの次のCiscoスイッチに進みます。 次の順序で、スイッチを1つずつアップグレードします。
リーフのCisco Nexus 9336C-FX2スイッチ: ovcasw15r1, ovcasw16r1
Spine Cisco Nexus 9336C-FX2スイッチ: ovcasw22r1, ovcasw23r1
Management Cisco Nexus 9348GC-FXPスイッチ: ovcasw21r1
このセクションの手順は、Oracle Private Cloud Applianceの一部として、コンポーネント・ファームウェアのアップグレードに固有です。
InfiniBandスイッチは、InfiniBandベースのネットワーク・アーキテクチャを持つシステムの一部です。
2.2.8以降のバージョンへのファームウェアのアップグレードの場合、符号なしバージョン2.2.7-2への中間アップグレードが必要です。 これにより、バージョン2.2.7-2を目的の新しいバージョンにアップグレードできます。 詳細は、「Oracle Private Cloud Applianceリリース・ノート」の「NM2-36P Sun Datacenter InfiniBand拡張スイッチ・ファームウェアのアップグレード2.2.9-3には2フェーズ・プロシージャが必要です」を参照してください。
ファームウェアのアップグレードに関する詳細情報は、「ファームウェアのバージョン2.2向けのSun Datacenter InfiniBand Switch 36製品ノート」 (ドキュメントID)にあります: E76431). " 「スイッチ・ファームウェアのアップグレード」 "の項を参照してください。
ファームウェア・アップグレードを実行する前に、NM2-36P Sun Datacenter InfiniBand拡張スイッチの現在の構成をバックアップすることをお薦めします。
バックアップおよびリストアの手順は、スイッチで使用されている現在のILOMバージョンに対応する「Oracle ILOM管理ガイド」のメンテナンスおよび構成管理セクションで提供されます。 次に例を示します。
InfiniBandスイッチ・ファームウェアのアップグレード
SSHおよびスーパーユーザー権限を持つアカウントを使用して、マスター管理ノードにログオンします。
Oracle Private Cloud Applianceソフトウェア・イメージに含まれているファームウェア・パッケージを解凍します。
[root@ovcamn05r1 ~]# mkdir /nfs/shared_storage/yum/nm2 [root@ovcamn05r1 ~]# cd /nfs/shared_storage/yum/nm2 [root@ovcamn05r1 nm2]# unzip /nfs/shared_storage/mgmt_image/firmware/IB_gateway/NM2-36P/p22173626_227_Generic.zip Archive: /nfs/shared_storage/mgmt_image/firmware/IB_gateway/NM2-36P/p22173626_227_Generic.zip inflating: license.txt inflating: readme_SUN_DCS_36p_2.1.8-1.txt creating: SUN_DCS_36p_2.1.8-1/ inflating: SUN_DCS_36p_2.1.8-1/pkey_filter.pl creating: SUN_DCS_36p_2.1.8-1/SUN_DCS_36p/ inflating: SUN_DCS_36p_2.1.8-1/SUN_DCS_36p/SUN-ILOM-CONTROL-MIB.mib inflating: SUN_DCS_36p_2.1.8-1/SUN_DCS_36p/SUN-FABRIC-MIB.mib inflating: SUN_DCS_36p_2.1.8-1/SUN_DCS_36p/
sundcs_36p_repository_2.1.8_1.pkg
inflating: SUN_DCS_36p_2.1.8-1/SUN_DCS_36p/SUN-HW-TRAP-MIB.mib inflating: SUN_DCS_36p_2.1.8-1/SUN_DCS_36p/SUN-DCS-IB-MIB.txt inflating: SUN_DCS_36p_2.1.8-1/SUN_DCS_36p/SUN-PLATFORM-MIB.mib inflating: SUN_DCS_36p_2.1.8-1/SUN_DCS_36p/ENTITY-MIB.mib inflating: SUN_DCS_36p_2.1.8-1/SUN_DCS_36p_2.1.8-1_metadata.xml inflating: SUN_DCS_36p_2.1.8-1/README_pkey_filter inflating: SUN_DCS_36p_2.1.8-1_THIRDPARTYLICENSE.pdfInfiniBandスイッチのいずれかにrootとしてログオンします。
root@ovcamn05r1 ~]# ssh root@192.168.4.202 root@192.168.4.202's password: You are now logged in to the root shell. It is recommended to use ILOM shell instead of root shell. All usage should be restricted to documented commands and documented config files. To view the list of documented commands, use "help" at linux prompt. [root@ilom-ovcasw19r1 ~]#
マスター構成とSubnetManagerの状態を確認してください。
[root@ilom-ovcasw19r1 ~]# getmaster Local SM not enabled Last change in Master SubnetManager status detected at: Thu Mar 22 14:29:18 UTC 2018 Master SubnetManager on sm lid 6 sm guid 0x13970201001ba4 : MT25408 ConnectX Mellanox Technologies Master SubnetManager Activity Count: 348521 Priority: 0
警告コマンド出力は、ローカルSMが有効になっていないことを確認する必要があります。 そうでない場合は、このプロシージャを中断し、Oracle Supportにご連絡ください。
現在のファームウェア・バージョンの詳細を一覧表示します。
[root@ilom-ovcasw19r1 ~]# version SUN DCS 36p version: 1.3.3-2 Build time: Feb 19 2013 13:29:01 SP board info: Manufacturing Date: 2012.06.23 Serial Number: "NCDBJ1073" Hardware Revision: 0x0007 Firmware Revision: 0x0000 BIOS version: SUN0R100 BIOS date: 06/22/2010
ILOMに接続し、ファームウェア・アップグレード手順を開始します。 要求された場合はYを押して、ファイルをロードしてください。
[root@ilom-ovcasw19r1 ~]# spsh Oracle(R) Integrated Lights Out Manager Version ILOM 3.0 r47111 Copyright (c) 2012, Oracle and/or its affiliates. All rights reserved. -> load -source http://192.168.4.1/shares/export/Yum/nm2/ \
SUN_DCS_36p_2.1.8-1/SUN_DCS_36p/sundcs_36p_repository_2.1.8_1.pkg
Downloading firmware image. This will take a few minutes. Are you sure you want to load the specified file (y/n) Setting up environment for firmware upgrade. This will take few minutes. Starting SUN DCS 36p FW update ========================== Performing operation: I4 A ========================== I4 fw upgrade from 7.3.0(INI:4) to 7.4.1010(INI:4): Upgrade started... Upgrade completed. INFO: I4 fw upgrade from 7.3.0(INI:4) to 7.4.1010(INI:4) succeeded =========================== Summary of Firmware update =========================== I4 status : FW UPDATE - SUCCESS I4 update succeeded on : A I4 already up-to-date on : none I4 update failed on : none ========================================== Performing operation: SUN DCS 36p firmware update ========================================== SUN DCS 36p upgrade from 1.3.3-2 to 2.1.8-1: Upgrade started... Upgrade completed. INFO: SUN DCS 36p upgrade from 1.3.3-2 to 2.1.8-1 succeeded Firmware update is complete. ILOM will be restarted and will take 2 minutes to come up. You will need to reconnect to Integrated Lights Out Manager.InfiniBandスイッチに再接続して、新しいファームウェアが実行中であることを確認し、SubnetManagerが無効な状態であることを確認します。
root@ovcamn05r1 ~]# ssh root@192.168.4.202 root@192.168.4.202's password: [root@ilom-ovcasw19r1 ~]# version SUN DCS 36p version: 2.1.8-1 Build time: Sep 18 2015 10:26:47 SP board info: Manufacturing Date: 2013.06.15 Serial Number: "NCDBJ1073" Hardware Revision: 0x0007 Firmware Revision: 0x0000 BIOS version: SUN0R100 BIOS date: 06/22/2010 [root@ilom-ovcasw19r1 ~]# getmaster Local SM not enabled
警告コマンド出力は、ローカルSMが有効になっていないことを確認する必要があります。 そうでない場合は、このプロシージャを中断し、Oracle Supportにご連絡ください。
最初のInfiniBandスイッチが正常にアップグレードを完了しており、正常にオンラインに戻っている場合は、IPアドレスが192.168.4.203である別のInfiniBandスイッチに接続して、同じプロシージャを実行します。
両方のInfiniBandスイッチがアップグレードされている場合、解凍されたパッケージを使用可能にするために作成した共有ストレージ・ディレクトリを削除します。
root@ovcamn05r1 ~]# cd /nfs/shared_storage/yum/ root@ovcamn05r1 yum]# ls -al total 323 drwxr-xr-x 8 root root 8 Mar 26 07:57 . drwxrwxrwx 31 root root 31 Mar 13 13:38 .. drwxr-xr-x 2 root root 5 Mar 13 12:04 backup_COMPUTE drwxr-xr-x 2 root root 5 Mar 13 13:19 current_COMPUTE drwxr-xr-x 3 root root 6 Mar 26 07:58
nm2
drwxr-xr-x 3 root root 587 Mar 13 12:04 OVM_3.4.4_1735_server drwxr-xr-x 3 root root 18 Mar 13 12:03 OVM_3.4.4_1735_transition drwxr-xr-x 4 root root 9 Mar 13 12:03 OVM_3.4.4_1735_update root@ovcamn05r1 yum]# rm -rf nm2/
このセクションの手順は、Oracle Private Cloud Applianceの一部として、コンポーネント・ファームウェアのアップグレードに固有です。
Fabric Interconnectは、InfiniBandベースのネットワーク・アーキテクチャを備えたシステムの一部です。
ファームウェアのアップグレードに関する詳細情報は、「XgOSユーザーズ・ガイド」 (ドキュメントID)にあります: E53170). " 「システム・イメージのアップグレード」 "の項を参照してください。
ファームウェア・アップグレードを実行する前に、Fabric Interconnectの現在の構成をバックアップすることをお薦めします。 バックアップ構成を別のサーバーに格納し、今後の参照用にファイル名にタイムスタンプを追加します。
詳細は、「XgOSユーザーズ・ガイド」 (ドキュメントID)の" 「構成の保存およびリストア」 "の項を参照してください: E53170).
Fabric Interconnectファームウェアのアップグレード
SSHおよびスーパーユーザー権限を持つアカウントを使用して、マスター管理ノードにログオンします。
Oracle Private Cloud Applianceソフトウェア・イメージからYumリポジトリ共有にファームウェア・パッケージをコピーします。
root@ovcamn05r1 ~]# cp /nfs/shared_storage/mgmt_image/firmware/IB_gateway/ \ OFI/xsigo-4.0.12-XGOS.xpf /nfs/shared_storage/yum/
Fabric Interconnectのいずれかに管理者としてログオンします。
root@ovcamn05r1 ~]# ssh admin@192.168.4.205 Password: Last login: Thu Oct 15 10:57:23 2015 from 192.168.4.4 Welcome to XgOS Copyright (c) 2007-2012 Xsigo Systems, Inc. All rights reserved. Enter "help" for information on available commands. Enter the command "show system copyright" for licensing information admin@ovcasw22r1[xsigo]
現在のファームウェア・バージョンの詳細を一覧表示します。
admin@ovcasw22r1[xsigo] show system version Build 3.9.4-XGOS - (buildsys) Thu Mar 19 03:25:26 UTC 2015 admin@ovcasw22r1[xsigo]
マスター構成とSubnetManagerの状態を確認してください。 必要に応じて、追加の診断コマンドを実行して詳細を確認します。
admin@ovcasw22r1[xsigo] show diagnostics sm-info - SM is running on ovcasw22r1 - SM Lid 39 - SM Guid 0x139702010017b4 - SM key 0x0 - SM priority 0 - SM State MASTER admin@ovcasw22r1[xsigo] show diagnostics opensm-param OpenSM $ Current log level is 0x83 OpenSM $ Current sm-priority is 0 OpenSM $ OpenSM Version : OpenSM 3.3.5 SM State : Master SM Priority : 0 SA State : Ready Routing Engine : minhop Loaded event plugins : <none> PerfMgr state/sweep state : Disabled/Sleeping MAD stats --------- QP0 MADs outstanding : 0 QP0 MADs outstanding (on wire) : 0 QP0 MADs rcvd : 6323844 QP0 MADs sent : 6323676 QP0 unicasts sent : 2809116 QP0 unknown MADs rcvd : 0 SA MADs outstanding : 0 SA MADs rcvd : 120021107 SA MADs sent : 120024422 SA unknown MADs rcvd : 0 SA MADs ignored : 0 Subnet flags ------------ Sweeping enabled : 1 Sweep interval (seconds) : 10 Ignore existing lfts : 0 Subnet Init errors : 0 In sweep hop 0 : 0 First time master sweep : 0 Coming out of standby : 0 Known SMs --------- Port GUID SM State Priority --------- -------- -------- 0x139702010017b4 Master 0 SELF 0x139702010017c0 Standby 0 OpenSM $ admin@ovcasw22r1[xsigo]
システムのアップグレード手順を開始します。
admin@ovcasw22r1[xsigo] system upgrade http://192.168.4.1/shares/export/Yum/xsigo-4.0.12-XGOS.xpf forcebaseos Copying... ################################################################ [100%] You have begun to upgrade the system software. Please be aware that this will cause an I/O service interruption and the system may be rebooted. The following software will be installed: 1. XgOS Operating System software including SCP Base OS 2. XgOS Front-panel software 3. XgOS Common Chassis Management software on IOC 4. XgOS VNIC Manager and Agent software 5. XgOS VN10G and VN10x1G Manager and Agent software 6. XgOS VHBA and VHBA-2 Manager and Agent software 7. XgOS VN10G and VN10x1G Manager and Agent software with Eth/IB Interfaces 8. XgOS VN4x10G and VN2x10G Manager and Agent software with Eth/IB Interfaces 9. XgOS VHBA-3 Manager and Agent software 10. XgOS VHBA 2x 8G FC Manager and Agent software Are you sure you want to update the software (y/n)? y Running verify scripts... Running preunpack scripts... Installing... ################################################################# [100%] Verifying... ################################################################# [100%] Running preinstall scripts... Installing Base OS - please wait... LABEL=/dev/uba /mnt/usb vfat rw 0 0 Rootfs installation successful The installer has determined that a reboot of the Base OS is required (HCA driver changed) The installer has determined that a cold restart of the Director is necessary Installing package... Running postinstall scripts... Installation successful. Please stand by for CLI restart. admin@iowa[xsigo] Rebooting OS. Please log in again in a couple of minutes... *********************************** Xsigo system is being shut down now *********************************** Connection to 192.168.4.204 closed.
再起動後、再度ログインできるようになるまでに約10分かかります。 アップグレードすると、管理ユーザーのパスワードがデフォルトの
admin
にリセットされます。 試行には数回かかる場合がありますが、最終的にデフォルト・パスワードでログインした場合に成功します。管理パスワードとルート・パスワードをファームウェアのアップグレード前の設定に変更するには、Fabric Interconnectに再接続します。
注意ファームウェアのアップグレード後に再びログインすると、この例のようなメッセージが表示される場合があります。
Message from syslogd@ovcasw22r1 at Fri Jun 22 09:49:33 2018 ... ovcasw22r1 systemcontroller[2713]: [EMERG] ims::IMSService [ims::failedloginattempt] user admin has tried to log on for 5 times in a row without success !!
これらのメッセージは、他のOracle Private Cloud Applianceコンポーネントからのログイン試行失敗を示します。 パスワードを元の値に戻した後で消去されます。
ユーザーrootと管理者のパスワードを次のように変更します。
admin@ovcasw22r1[xsigo] set system root-password Administrator's password: admin New password:
myOriginalRootPassword
New password again:myOriginalRootPassword
admin@ovcasw22r1[xsigo] set user admin -password New password:myOriginalAdminPassword
New password again:myOriginalAdminPassword
Fabric Interconnectに再接続して、新しいファームウェアが稼働していることを確認し、すべてのvNICsおよびvHBAsが稼働状態であることを確認します。
root@ovcamn05r1 ~]# ssh admin@192.168.4.205 admin@ovcasw22r1[xsigo] show system version Build 4.0.12-XGOS - (buildsys) Fri Jun 22 04:42:35 UTC 2018 admin@ovcasw22r1[xsigo] show diagnostics sm-info - SM is running on ovcasw22r1 - SM Lid 39 - SM Guid 0x139702010017b4 - SM key 0x0 - SM priority 0 - SM State MASTER admin@ovcasw22r1[xsigo] show vnic name state mac-addr ipaddr if if-state ---------------------------------------------------------------------------------------------- eth4.ovcacn08r1 up/up 00:13:97:59:90:11 0.0.0.0/32 mgmt_pvi(64539) up eth4.ovcacn09r1 up/up 00:13:97:59:90:0D 0.0.0.0/32 mgmt_pvi(64539) up eth4.ovcacn10r1 up/up 00:13:97:59:90:09 0.0.0.0/32 mgmt_pvi(64539) up eth4.ovcacn11r1 up/up 00:13:97:59:90:1D 0.0.0.0/32 mgmt_pvi(64539) up eth4.ovcacn12r1 up/up 00:13:97:59:90:19 0.0.0.0/32 mgmt_pvi(64539) up [...] eth7.ovcacn29r1 up/up 00:13:97:59:90:28 0.0.0.0/32 5/1 up eth7.ovcamn05r1 up/up 00:13:97:59:90:04 0.0.0.0/32 4/1 up eth7.ovcamn06r1 up/up 00:13:97:59:90:08 0.0.0.0/32 5/1 up 40 records displayed admin@ovcasw22r1[xsigo] show vhba name state fabric-state if if-state wwnn ------------------------------------------------------------------------------------------------ vhba03.ovcacn07r1 up/up down(Down) 12/1 down 50:01:39:71:00:58:B1:0A vhba03.ovcacn08r1 up/up down(Down) 3/1 down 50:01:39:71:00:58:B1:08 vhba03.ovcacn09r1 up/up down(Down) 12/1 down 50:01:39:71:00:58:B1:06 vhba03.ovcacn10r1 up/up down(Down) 3/1 down 50:01:39:71:00:58:B1:04 [...] vhba04.ovcacn29r1 up/up down(Down) 12/2 down 50:01:39:71:00:58:B1:13 vhba04.ovcamn05r1 up/up down(Down) 3/2 down 50:01:39:71:00:58:B1:01 vhba04.ovcamn06r1 up/up down(Down) 12/2 down 50:01:39:71:00:58:B1:03 20 records displayed
最初のFabric Interconnectでアップグレードが正常に完了し、オンラインに戻っている場合は、IPアドレスが192.168.4.204で他のFabric Interconnectに接続し、同じプロシージャを実行します。