4.177 dact-lbp

Use this command to deactivate a previously activated loopback point test, if a test is active. If no test is active, the command attempts to clear both near-end and far-end latched loopback points.

Parameters

link (mandatory)
SS7 signaling link. The signaling link for which the loopback point test is being deactivated.
Synonym:
port
Range:
a, b, a1 - a31, b1 - b31

Not all card types support all link parameter values.

See Table A-1 for valid link parameter range values for each type of card that can have a location specified in the loc parameter.

loc (mandatory)
Card location. The unique identifier of the card containing the signaling link on which loopback point testing is to be deactivated.
Range:
1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

Example

dact-lbp:loc=1205:link=b

Dependencies

The specified signaling link must be equipped.

For clearing a remotely initiated loopback or LFS test stop, the card location (loc parameter) must be an or E5-E1T1-B card, provisioned with the LIMT1 card type, configured with either the SS7ANSI or CCS7ITU application.

This command cannot be entered until any previously issued act-lbp or dact-lbp command is accepted.

If an LFS test is about to complete, a new dact-lbp command cannot be entered until the test completes.

This command cannot be entered to cancel a signaling link test (a tst-slk test).

This command cannot be entered to cancel a Command Driven Loopback test.

The specified link must exist, and the maximum number of allowed LFS or signaling link tests must not already be in progress. At least one active LFS or signaling link test must be completed before this command can be entered again.

This command cannot be entered during upgrade.

The specified signaling link must not be active.

For clearing a remotely initiated loopback, the card location specified in the loc parameter must be equipped.

For clearing a remotely initiated loopback, the card location specified in the loc parameter must be in service (IS-NR).

For clearing a remotely initiated loopback, the card location specified in the loc parameter cannot be reserved by the system.

Notes

After the deactivation of loopback point testing has started, you cannot cancel the process.

If an LFS test is aborted by a card reset, it could leave the remote far-end loop-back condition active. Use the dact-lbp command to cancel LFS tests.

Output

The following example output is generated only when a latched loopback is cleared and when there were no active loopback tests in progress.

Note:

This situation could occur even if there were no latched loopbacks to be cleared.
dact-lbp:loc=1205:link=b

    rlghncxa03w 04-02-17 16:02:05 EST  EAGLE5 33.0.0
    LOC = 1205  LINK = B 
    CLEAR STATUS = PASS, loopback was cleared. 
;

The following example output is generated only when a latched loopback could not be cleared when there were no active loopback tests in progress.

dact-lbp:loc=1205:link=b

    rlghncxa03w 04-02-17 16:02:05 EST  EAGLE5 33.0.0
    LOC = 1205  LINK = B
    CLEAR STATUS = ERROR, loopback could not be cleared. 
;