| Skip Navigation Links | |
| Exit Print View | |
|
Netra SPARC T4-1 Server HTML Document Collection |
Confirming Server and Site Specifications
Overcurrent Protection Requirements
DC Power Source, Power Connection, and Grounding Requirements
Stabilize the Rack for Installation
Mounting the Server Into a 4-Post Rack
Mounting the Server Into a 2-Post Rack
Connecting Data and Management Cables
Powering On the Server for the First Time
Connect a Terminal or Emulator to the SER MGT Port
Power On the Server for the First Time
Oracle Solaris OS Configuration Parameters
Assign a Static IP Address to the SP
Understanding System Administration Resources
Platform-Specific Oracle ILOM Features
Oracle VM Server for SPARC Overview
Hardware Management Pack Overview
Source for Downloading Hardware Management Pack Software
Hardware Management Pack Documentation
Display the Oracle ILOM -> Prompt
Power On the Server (Oracle ILOM)
Power Off the Server (Oracle ILOM)
Reset the Server (Oracle Solaris OS)
Reset the Server (Oracle ILOM)
Reset the SP to Default Values
Important Hardware RAID Guidelines
Prepare to Use the FCode Utility
Hot Spare Drives in RAID Volumes (LSI)
Determining If a Drive Has Failed
RAID Drive Replacement Strategies
Changing Server Identification Information
Change Customer Data on FRU PROMs
Change System Identifier Information
Restore the Host Power State at Restart
Specify the Host Power State at Restart
Disable or Re-Enable the Host Power-On Delay
Specify Parallel Boot of the SP and Host
Configure Host Behavior (Keyswitch State)
Disable or Re-Enable Network Access to the SP
Display the DHCP Server IP Address
Display the IP Address of the SP
Using an In-band Connection to the SP
Configure the Host Boot Mode (Oracle VM Server for SPARC)
Change the Host Boot Mode Behavior at Reset
Manage the Host Boot Mode Script
Display Host Boot Mode Expiration Date
Override OBP Settings to Reset the Server
Configuring Server Behavior at Restart
Specify Behavior When the Host Resets
Specify Behavior When the Host Stops Running
Specify Behavior at Boot Timeout
Specify Behavior if Restart Fails
Specify Maximum Restart Attempts
Enabling Automatic System Recovery
Identifying WWN-Designated SAS2 Devices
Mapping WWN Values to Hard Drives (OBP probe-scsi-all Command)
Identify a Disk Slot Using prtconf (Oracle Solaris OS)
WWN Syntax in an OS Installation on an Individual Drive
WWN Syntax in an OS Installation on a RAID Volume
Power Supply, Hard Drive, and Fan Module Locations
Top Cover, Filter Tray, and DVD Tray Locations
Motherboard, DIMMs, and PCI Board Locations
Understanding Fault Management Commands
Interpreting Log Files and System Messages
Checking if Oracle VTS Is Installed
Component Service Task Reference
Removing Power From the Server
Determine if the Hard Drive Fan Is Faulty
Servicing the Hard Drive Backplane
Determine if the Hard Drive Backplane Is Faulty
Remove the Hard Drive Backplane
Install the Hard Drive Backplane
Verify the Hard Drive Backplane
Servicing the Power Distribution Board
Determine if the Power Distribution Board Is Faulty
Remove the Power Distribution Board
Install the Power Distribution Board
Verify the Power Distribution Board
Determine if the DVD Drive Is Faulty
Determine if the LED Board Is Faulty
Determine if the Fan Board Is Faulty
Servicing the PCIe2 Mezzanine Board
Determine if the PCIe2 Mezzanine Board Is Faulty
Remove the PCIe2 Mezzanine Board
Install the PCIe2 Mezzanine Board
Verify the PCIe2 Mezzanine Board
Locate a Faulty PCIe2 Riser Card
Remove a PCIe2 Card From the PCIe2 Mezzanine Board
Remove a PCIe2 Card From the PCIe2 Riser Card
Install a PCIe2 Card Into the PCIe2 Mezzanine Board
Install a PCIe2 Card Into the PCIe2 Riser Card
Install SAS Cable for Sun Storage 6 Gb SAS PCIe RAID HBA, Internal
Servicing the Signal Interface Board
Determine if the Signal Interface Board Is Faulty
Remove the Signal Interface Board
Install the Signal Interface Board
Verify the Signal Interface Board
Determine if the Battery Is Faulty
Determine if the ID PROM Is Faulty
Determine if the Motherboard Is Faulty
Returning the Server to Operation
Power On the Server (Oracle ILOM)
Rack CautionsStabilize the Rack for InstallationInstalling the ServerInstall a Server (19-Inch, 2-Post Sliding Rail Rackmount Kit) Install the Server (19-Inch, 4-Post Sliding Rail Rackmount Kit)Install the Server (23‐Inch, 2-Post Hardmount Rackmount Kit)600-mm, 4‐Post Hardmount Rackmount KitStabilize the Rack for InstallationConfiguring Hardware RAIDCreate a Hardware RAID VolumePrepare to Use the FCode UtilityHardware RAID SupportRear Panel ComponentsRear Panel ComponentsEnvironmental RequirementsRemove the Air FilterRemove the BatteryRemove a DIMMRemove the DVD DriveRemove the DVD TrayRemove the Fan BoardRemove a Fan ModuleRemove the Air FilterRemove a Hard DriveRemove the Hard Drive BackplaneRemove the Hard Drive FanRemove the ID PROMRemove the LED BoardRemove the MotherboardRemove a PCIe2 Card From the PCIe2 Mezzanine BoardRemove a PCIe2 Card From the PCIe2 Riser CardRemove the PCIe2 Mezzanine BoardRemove a PCIe2 Riser CardRemove the Power Distribution BoardRemoving Power From the ServerRemove a Power SupplyRemove the Signal Interface BoardRemove the SPRemove the Top CoverVerify the BatteryVerify a DIMMVerify the DVD DriveVerify the Fan BoardVerify a Fan ModuleVerify a Hard DriveVerify the Hard Drive BackplaneVerify the Hard Drive FanVerify the ID PROMVerify the LED BoardVerify the MotherboardVerify a PCIe2 CardVerify the PCIe2 Mezzanine BoardVerify a PCIe2 Riser CardVerify the Power Distribution BoardVerify a Power SupplyVerify the Signal Interface BoardVerify the SPSet the Boot Timeout IntervalSpecify Behavior at Boot TimeoutSpecify Behavior if Restart FailsSpecify Behavior When the Host Stops RunningSpecify Maximum Restart AttemptsSpecify Behavior When the Host ResetsReturning the Server to Operation
|