Go to main content
oracle home
Configuring an Oracle
®
Solaris 11.4 System as a Router or a Load Balancer
Exit Print View
Search Term
Search Scope:
This Document
Entire Library
» ...
Documentation Home
»
Oracle Solaris 11.4 Information Library
»
Configuring an Oracle
®
Solaris ...
»
Configuring a System as a Router
»
Configuring Routing
Updated: November 2020
Configuring an Oracle
®
Solaris 11.4 System as a Router or a Load Balancer
Document Information
Using This Documentation
Product Documentation Library
Feedback
Chapter 1 Introduction to Routers
Router Overview
Routing Protocols
Routing Information Protocol
ICMP Router Discovery Protocol
Quagga Routing Protocol Suite
Routing Tables and Routing Types
Using Rights Profiles to Perform Network Configuration
Chapter 2 Configuring a System as a Router
Configuring an IPv4 Router
How to Configure an IPv4 Router
Configuring an IPv6 Router
in.ripngd Daemon, for IPv6 Routing
Router Advertisement, Prefixes, and Messages
How to Configure an IPv6-Enabled Router
Configuring Routing
Creating Persistent (Static) Routes
How to Add a Persistent Route by Specifying Destination and Gateway
How to Specify a Name for a Persistent Route
Enabling Routing for Single-Interface Systems
How to Enable Dynamic Routing on a Single-Interface System
About IPv6 Routing
Configuring Multihomed Hosts
How to Create a Multihomed Host
Implementing Symmetric Routing on Multihomed Hosts
Chapter 3 Using Virtual Router Redundancy Protocol
Overview of VRRP
How VRRP Works
About the Layer 3 VRRP Feature
Comparing Layer 2 and Layer 3 VRRP
Limitations of Layer 2 and Layer 3 VRRP
Chapter 4 Configuring and Administering Virtual Router Redundancy Protocol
Planning a VRRP Configuration
Installing VRRP
How to Install VRRP
Configuring VRRP
Creating a VRRP VNIC for Layer 2 VRRP
Creating a VRRP Router
Configuring the Virtual IP Address for Layer 2 and Layer 3 VRRP Routers
Enabling and Disabling VRRP Routers
Modifying a VRRP Router
Displaying Layer 2 and Layer 3 VRRP Router Configurations
Displaying IP Addresses That Are Associated With VRRP Routers
Deleting a VRRP Router
Controlling Gratuitous ARP and NDP Messages
Use Case: Configuring a Layer 2 VRRP Router
Use Case: Configuring a Layer 3 VRRP Router on an IPMP Interface
Chapter 5 Overview of an Integrated Load Balancer
About the Integrated Load Balancer
Features of ILB
ILB Components
How ILB Works
ILB Operation Modes
Direct Server Return Mode
Network Address Translator Mode
Half-NAT Load-Balancing Mode
Full-NAT Load-Balancing Mode
Chapter 6 Configuring and Managing the Integrated Load Balancer
Preparing to Use ILB
How to Deploy ILB
Managing an ILB
Defining Server Groups and Back-End Servers
Creating an ILB Server Group
Adding Back-End Servers to an ILB Sever Group
Enabling or Disabling a Back-End Server in an ILB Server Group
Deleting a Back-End Server From an ILB Server Group
Deleting ILB Server Groups
Monitoring Health Checks in ILB
Creating a Health Check
Listing Health Checks
Displaying Health Check Results
Deleting a Health Check
Configuring ILB Rules
ILB Algorithms
Creating an ILB Rule
Listing ILB Rules
Deleting an ILB Rule
Use Case: Configuring an Integrated Load Balancer
Displaying ILB Statistics
Displaying ILB Statistics
Displaying the NAT Connection Table
Displaying the Session Persistence Mapping Table
Importing and Exporting Configurations
Chapter 7 Configuring ILB for High Availability
Configuring ILB for High Availability By Using the DSR Topology
How to Configure ILB for High Availability by Using the DSR Topology
Configuring ILB for High Availability by Using the Half-NAT Topology
How to Configure ILB for High-Availability by Using the Half-NAT Topology
Index
Index Numbers and Symbols
Index A
Index B
Index C
Index D
Index E
Index G
Index H
Index I
Index L
Index M
Index N
Index O
Index P
Index Q
Index R
Index S
Index T
Index V
Language:
English
Configuring Routing
This section discusses additional procedures to configure routing.
Previous
Next