Go to primary content
Oracle® Enterprise Communications Broker Administrator's Guide
Release P-CZ3.2.0
Next
Contents
List of Figures
List of Tables
Title and Copyright Information
About This Guide
My Oracle Support
1
Applicable Platforms
Software Packaging
Oracle Server X8-2 Platform Preparation
Available Connections
Cable the Oracle X8-2
Cable the Local Console
Connect ILOM to the Oracle X8-2
Install the Software on the X8-2
Next Steps After the Software Installation
Oracle Server X7-2 Platform Preparation
Cable the Oracle X7-2
Available Connections
Cable the Local Console
Connect ILOM to the Oracle X7-2
Software Installation - Oracle X7-2 Platforms
Known Issues
Netra Server X5-2 Platform Preparation
Cable the Netra X5-2 for Communications
Available Connections
Cable the Local Console
Connect ILOM to the Netra X5 for Communications
Software Installation - Netra and Server-based Platforms
Known Issues
Cabling the Netra Server X3-2 for Acme Packet
Available Connections
Cable the Local Console
Cable ILOM
Cable the Network Management Ports
Cable the Media and Signaling Network Interfaces
HA Cabling
Rear Panel Cabling for HA
Cable a Single Rear Interface for HA
Configure the BIOS Setting
Virtual Systems
Log On to the System
2
Hardware Installation Summary
Connecting to The
Oracle Enterprise Communications Broker
Local Connections and Time-outs
SSH Connections and Time-outs
Initiate SSH without Username and Password
SSH with Username and Password
GUI Access
Setting Your Login Banner
System Boot
Oracle Enterprise Communications Broker
Boot Parameters
Upload the Stage 3 Boot Loader and System Image
Boot Parameter Changes
Set Boot Parameters Wizard
Configurable Boot Loader Flags
Set Boot Parameters from the ACLI
Change Boot Parameters by Interrupting a Boot in Progress
Set Management IP Address
Format Hard Drive
System Image Filename
Initialize the System
Add a License with the Set License Wizard
Setting Up System Basics
New User and Superuser Passwords
New System Prompt
3
System Administration
Save and Activate
General Settings and System Config Settings
Configure an NTP Server
High Availability Settings
Overview
Establishing Active and Standby Roles
Configure High Availability
Force an HA Switchover
Configure System Config
SNMP Configuration
Configure SNMP Settings
Logging (Syslog)
Overview
Process Log Messages
Add a Syslog Server
Configure Syslog Settings
Enterprise Operations Monitor
Add a Monitor Collector
Configure Communications Monitoring Probe Settings
Support for Multiple VLANs
Add Multiple VLANs
Accounting Settings
Configure an Accounting Server
Configure Accounting
FTP Push
Multiple Push Receivers
Secure FTP Push Configuration
Add an FTP Push Receiver
Network Interface Configuration
Configure a Network Interface
Enable ICMP
Configure the Network Interface for High Availability Operations
Virtual MAC Addresses
Security Settings
SHA 2 Support
Add a Certificate Record
TLS Profile Configuration
Generate a Certificate Request
Import a Certificate
RADIUS Authentication
Management Protocol Behavior
RADIUS Authentication Configuration
Global Authentication Settings
RADIUS Server Settings
TACACS+ Overview
TACACS+ Authentication
ASCII Log In
PAP Log In
CHAP Log In
Authentication Message Exchange
TACACS+ Header
Authentication START Packet
Authentication REPLY Packet
Authentication CONTINUE Packet
Authentication Scenarios
ASCII Authentication
PAP Authentication
CHAP Authentication
TACACS+ Authorization
Authorization Message Exchange
Authorization REQUEST Packet
Authorization RESPONSE Packet
Authorization Pass
Authorization Fail
TACACS+ Accounting
Accounting Message Exchange
Accounting REQUEST Packet
Accounting REPLY Packet
Accounting Scenario
Managing TACACS+ Operations
TACACS+ MIB
SNMP Trap
TACACS+ Faults
TACACS+ Logging
TACACS+ Configuration
Add TACACS+ Authentication and Servers
SIP Interface Settings
Proxy Registrations
Add a SIP Interface
Configure SIP Config
Restricting Session Initiation
Configure a SIP Interface Port
SIP Monitor and Trace Filter Configuration
SIP REFER
SIP REFER Method Call Transfer for ECB
Unsuccessful Transfer Scenarios
Call Flows
Configure SIP REFER Method
180 and 100 NOTIFY in REFER Call Transfers for the ECB
Sample Messages
180 and 100 NOTIFY Configuration
SNMP
Overview
Basic SNMP Parameters
SNMP Community
Trap Receivers
SNMP Community Settings
Set Trap Receiver Settings
Web Server Settings
4
Maintenance and Debugging
Your
Oracle Enterprise Communications Broker
Image
Obtain a New Image
Upgrade Software - Web GUI System Tab
Display Log Files
Display System Health
Obtain Support Information