4.146 chg-t1
Use this command to change an interface for a T1 card in the system. T1 cards consist of /E5-E1T1-B cards used as T1 or ST-HSL-A cards.
Parameters
- loc (mandatory)
- The card location as stenciled on the shelf of the system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
- t1port (mandatory)
- T1 port number
The value must be a T1 port that has already been configured with a T1 interface on the specified T1 card.
- framing (optional)
- Indicator for framing format. esfperf is the framing format with performance monitoring.
Example
chg-t1:loc=1205:t1port=1:encode=ami
chg-t1:loc=1205:t1port=2:encode=b8z:ll=250s
chg-t1:loc=1205:t1port=1:minsurate=1000
chg-t1:loc=1205:t1port=1:encode=ami:t1tsel=external
Dependencies
At least one optional parameter must be specified.
The card location specified by the loc parameter must be equipped.
The E1/T1 table must be accessible.
The Card (IMT) table must be accessible.
The card specified by the loc parameter must be a LIMT1 card type.
The port specified by the t1port parameter must have already been configured with a T1 interface on the specified T1 card.
All signaling links that are serviced by the specified T1 card must be deactivated before the values for the encode, t1tsel, ll, and framing parameters can be changed.
The shelf FAN bit must be turned ON for the shelf on which an E5-E1T1-B card is provisioned and present. The system checks the shelf FAN bit when an E5-E1T1-B card is present in the specified odd card location (loc parameter) and the chanbrdg=on parameter is specified.
HIPR2 cards must be equipped in card locations xy09 and xy10 (x is the frame, y is the shelf) on each EAGLE shelf that contains one or more /E5-E1T1-B cards. The system checks for HIPR2 cards when the chanbrdg=on parameter is specified for /E5-E1T1-B cards.
The following card locations cannot be specified in the loc parameter: 1113 - 1118 (E5-MASP and E5-MDAL cards), or xy09 and xy10 where x is the frame and y is the shelf (MUX cards).
The linkclass=unchan parameter must be specified (see the ent-t1
command) before the minsurate parameter can be specified.
The ST-HSL-A feature must be turned on before the framing=esfperf parameter can be specified.
Notes
External timing is derived from the EAGLE High-Speed Master Clock (1.544 MHz for T1 or 2.048 MHz for E1): therefore, the Master Timing feature is required. Line timing is derived from its received data stream, if present.
Output
chg-t1:loc=1205:t1port=1:encode=ami
rlghncxa03w 04-01-20 09:07:58 EST EAGLE 31.3.0
CHG-T1: MASP A - COMPLTD
;