ent-card

Use this command to add a card to the database. The card type and application specifies the function assigned to the card.

Parameters

Note:

The phrase "Service Module card" refers to an E5-SM8G-B or SLIC card when any of these cards can be used to provision the VSCCP, DEIRHC, SIPHC, and ENUMHC application. The cards are provisioned with the type=dsm or type=slic and appl=deirhc/enumhc/siphc/vsccp parameters.

appl (mandatory)

Application. The application for the card.

Range:

xyyyyyy

1 alphabetic character followed by up to 6 alphanumeric characters. Valid applications are:

atmansi—Used by E5-ATM-B cards to support ANSI high-speed ATM signaling links and T1 functions.

atmitu—Used by E5-ATM-B cards to support ITU E1 high-speed ATM signaling links and E1 functions.

ccs7itu—Used by E5-E1T1-B, and SLIC cards for ITU-TSS MTP functions.

deirhc—Used by E5-SM8G-B and SLIC cards to support the S13/S13' EIR feature.

elap- Used by E5-APP-B card to support ELAP/LNP functionality.

enumhc- Used by E5-SM8G-B and SLIC cards to support the ENUM application.

epap - Used by E5-APP-B card to support EPAP/RTDB functionality.

eroute—Used by STC and E5-STC cards for EAGLE 5 Integrated Monitoring Support functions.

gls—Used by E5-TSM cards for downloading gateway screening to LIM and Service Module cards.

imf --- Used by E5-APP-B card to support IMF functionality.

ipgwi—Used by E5-ENET-B cards for IP point-to-multipoint connectivity for ITU point codes.

iplimi—Used by E5-ENET-B cards for IP point-to-point connectivity for ITU point codes.

ips—Used by E5-IPSM and E5-ENET-B cards for the IP User Interface feature.

ipsg—Used by E5-ENET-B, and SLIC cards to support the combined functionality of IPLIMx M2PA and IPGWx M3UA.

lsms - Used by E5-APP-B card to support LSMS/LNP functionality.

mcp—Used by E5-MCPM-B cards for the Measurements Platform feature.

nas - Used by E5-APP-B card to support NAS (storage of LNPDB from LSMS) functionality.

sfapp— Used by SLIC cards to support the SFAPP application.

siphc— Used by E5-SM8G-B and SLIC Cards to support SIP application.

ss7ansi—Used by E5-E1T1-B, and SLIC cards for ANSI MTP functions.

ss7ipgw— Used by E5-ENET-B cards for TCP/IP point-to-multipoint connectivity.

switch - Used by Telco switch to add power consumed by Telco Switch to Frame Power Budget. This is not an application gpl.

vsccp—Used by Service Module cards to support EPAP-based features and LNP features. If no EPAP-based features or LNP features are turned on, and a Service Module card is present, the VSCCP GPL processes GTT traffic.

loc (mandatory)

The card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311- 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 6201 - 6208, 6211 - 6218, 6301 - 6308, 6311 - 6318

type (mandatory)

The type of hardware being added.

Range:

dcm: Data Communications Module card (E5-ENET-B card). Applications for this card type are IPLIMI, SS7IPGW, and IPGWI.
dsm: E5-SM8G-B or SLIC card to support EPAP-based features, LNP features, and the GTT feature. The application for this card type is VSCCP. The E5-SM8G-B and SLIC cards also supports the S13/S13' EIR, ENUM, and SIP Number Portability features. The application for the E5-SM8G-B or SLIC card running the S13/S13' EIR, ENUM, or SIP application is DEIRHC, ENUMHC, or SIPHC respectively.
e5appb: E5-APP-B card to support ELAP, EPAP, IMF, LSMS, and NAS applications.
enet: E5-ENET-B card to support the IP Signaling Gateway. The application for this card type is IPSG.
enetb: E5-ENET-B or SLIC card to support the IP Signaling Gateway. The application for this card type is IPSG
ipsm: IP Services Module card (E5-IPSM or E5-ENET-B card) to support the IP User Interface feature. The application for this card type is IPS.
limatm: E5-ATM-B card to support high-speed signaling links. The application for this card type is ATMANSI.
lime1atm: E5-ATM-B card to support high-speed signaling links. The application for this card type is ATMITU.
lime1: E5-E1T1-B, or SLIC card used as an E1 card or an SE-HSL card. Applications for this card type are SS7ANSI and CCS7ITU.
limt1: E5-E1T1-B, or SLIC card used as a T1 card or an SE-HSL card; or E5- E1T1-B card used as an ST-HSL card. Applications for this card type are SS7ANSI or CCS7ITU
mcpm: E5-MCPM-B card used as a Measurement Collection and Polling Module (MCPM) card for the Measurements Platform feature. The application for this card type is MCP.
slic: SLIC card to support Service Module Applications and IP Signaling Gateway. The application for this card type are IPSG (with or without GTT functionality), VSCCP, DEIRHC, SIPHC, ENUMHC, or SFAPP.
stc: E5-ENET-B or SLIC card used as a Signaling Transport Card (STC or E5-STC) for the EAGLE 5 Integrated Monitoring Support feature. The application for this card type is EROUTE.
telco: TELCO switch to add power consumed by Telco Switch to Frame Power Budget.
tsm: E5-TSM card used for Gateway Screening. The application for this card type is GLS.

data (optional)

The type of OAM/MPS data that can be loaded on an E5-SM8G-B or a SLIC card.

Range:

dn: only DN related data from EPAP is loaded on the card
elap: ELAP data are loaded on the card
epap: all RTDB data (DN + IMSI) from EPAP are loaded on the card

Note:
The epap value cannot be specified when the EPAP Data Split feature is ON.
gtt: only OAM data are loaded on the card. The card will not load any ELAP or EPAP data at all.
imsi: only IMSI related data from EPAP is loaded on the card
nosccp: only OAM data, excluding GTT data is loaded on the card. No GTT or MPS data will be downloaded on the card. This value (=nosccp) of the data parameter is valid only for IPSG card(s) with the type=slic.

Note:
The nosccp value signifies the absence of SCCP functionality on the IPSG card, and that it behaves as a regular IPSG card.

Default:: nosccp

force (optional)

If the force=yes parameter is used to add a LIM card to the database, it is recommended that you add the required number of Service Module cards to the database after the LIM card is added to avoid the loss of global title translation (GTT) traffic.

Range:: no; yes

Default:: yes

sflog (optional)

The sflog=yes parameter is used to configure a logging IPS card for logs collection.

Range:: no; yes

Default:: no

srvname (optional)

The name/identifier of the server/host running on E5-APP-B cards and Telco Switches.

Range:: yyyyyyyyyyyyyyyy

Example

ent-card:loc=1206:type=limatm:appl=atmansi:force=yes

ent-card:loc=1208:type=limatm:appl=atmansi:force=no

ent-card:loc=1105:type=enet:appl=ipsg

ent-card:loc=1201:type=dsm:appl=vsccp:data=dn

ent-card:loc=1101:type=e5appb:appl=epap:srvname=tklcepap:force=yes

ent-card:loc=1103:type=e5appb:appl=elap:srvname=tklcelap

ent-card:loc=6201:type=telco:appl=switch:srvname=telco1

ent-card:loc=1101:type=dsm:appl=siphc=data=dn

ent-card:loc=1101:type=dsm:appl=vsccp:data=elap

ent-card:loc=1104:type=dsm:appl=deirhc

ent-card:loc=1101:type=dsm:appl=enumhc

ent-card:loc=1111:type=ipsm:appl=ips:sflog=yes

ent-card:loc=1103:type=slic:appl=ipsg

ent-card:loc=1105:type=slic:appl=vsccp //odd slot

ent-card:loc=1106:type=slic:appl=vsccp //even slot

ent-card:loc=1108:type=slic:appl=sfapp

Dependencies

Note:

The LNP feature is "turned on" when an LNP ported TNs quantity is shown in the rtrv-ctrl-feat command output.

For features that are enabled with the enable-ctrl-feat command, use the rtrv-ctrl-feat command to verify whether a feature is enabled or turned on. For features that are turned on with the chg-feat command, use the rtrv-feat command to display the ON or OFF status of the features.

Table A-9 shows the card names, the only valid card type (type parameter) and application (appl parameter) combinations, the card part numbers, and the maximum number of cards allowed in the database.

The card location must not be 1113-1118, xy09 or xy10 where x is the frame and y is the shelf.

The specified shelf location must be provisioned and present in the frame.

The specified card location cannot already be provisioned in the database.

The DSM card must be inserted into an odd-numbered location. The n+1 slot next to the DSM card must be empty, where n is the odd-numbered location (for example, if the DSM card is in location 1101, then the 1102 slot must be empty and unprovisioned).

The Measurements Platform feature must be turned on before the command can be entered for an MCPM card (type=mcpm:appl=mcp).

A valid value must be specified for the appl parameter.

The Shelf table is corrupt or cannot be found.

The IMT (Card) table is corrupt or cannot be found.

A card that is in an active maintenance state cannot be provisioned with this command. A card must be in the Out-of Service-Memory Administration (OOS-MA) state before it can be provisioned.

The n+1 slot next to the DSM card must be empty, where n is the odd-numbered location (for example, if the DSM card is in location 1101, then the 1102 slot must be empty and unprovisioned).

The GTT feature must be turned on to specify the appl=vsccp parameter.

The GWS feature must be turned on to specify the appl=gls parameter.

A valid card type must be specified. See the description for the type parameter for a list of valid values.

Table A-9 lists the maximum number of cards of each card type and application that are allowed in the system.

The MAS Configuration table is corrupt or cannot be found.

All provisioned shelves must contain HIPR cards before more than 115 LIM-ATM cards can be provisioned.

If ELAP or EPAP is specified for the data parameter for VSCCP, then the Dual ExAP Config feature must be enabled.

When data=gtt is specified for VSCCP, either the Dual ExAP Config feature must be enabled or the EPAP Data Split feature must be turned ON.

If DN or IMSI is specified for the data parameter for VSCCP, the EPAP Data Split feature must be turned on.

If the EPAP Data Split feature is turned on or the Dual ExAP Config feature is enabled, and the value specified for the loc parameter indicates an E5-SM8G-B or SLIC card, then the data parameter must be specified. The data parameter can be specified only for an E5-SM8G-B or SLIC card running the VSCCP or SIPHC application on an IPSCP card.

Note:

The data parameter is valid only for SLIC IPSG cards, and not ENET/ENET-B IPSG cards.

The Diameter S13/S13' Interface for EIR feature must be enabled before the type=dsm and appl=deirhc parameters can be specified.

The data parameter is not allowed with the DEIRHC GPL.

The parameter sflog=yes can be specified only when the type=ipsm and appl=ips parameters are specified.

A maximum of 32 EPAP based cards can be provisioned with type=dsm and data=EPAP/DN/IMSI.

A maximum of 2 SFLOG cards can be provisioned.

The SIPNP feature must be enabled before the type=dsm and appl=siphc parameters can be specified.

The DATA parameter can only be equal to EPAP/ELAP when type=dsm and appl=siphc parameters are specified.

If the IPSG32 GPL is running on the location specified by the loc parameter, then data=gtt and data=nosccp are the only valid values for the DATA parameter. If the GPL is anything but IPSG32 GPL, data=nosccp cannot be used for the card on that location.

The srvname parameter must be specified for an E5-APP-B card and Telco Switch.

The srvname must be unique for each E5-APP-B card and Telco Switch to be provisioned in the system.

Unless the force parameter is specified, two E5-APP-B cards running the same application cannot be provisioned in slots drawing power from the same FAP power source. EAGLE shelf card slots XXX1, XXX2, XXX5, and XXX6 draw power from the A designation FAP power source. Cards XXX3, XXX4, XXX7, and XXX8 draw power from the B designation FAP power source.

The srvname parameter can only be used with E5-APP-B card or Telco Switch.

Telco switch can only be provisioned in a shelf with type equal to FPB.

E5-APP-B card and Telco switch cannot be provisioned in the same shelf. They are mutually exclusive.

A maximum of 6 Telco switches can be provisioned in a shelf.

E5-ENET-B, SLIC, and E5-APP-B cards can be provisioned if the shelf FAN bit is turned ON.

When re-entering the command for the provisioning of the 26^th Service Module card, the re-entered command must specify type=dsm and the same loc value as the original command. See "Service Module Cards" under Notes for more information.

The data parameter can only be specified for IPSG application running on SLIC card.

Notes

ITU Environment

The force parameter can be specified to add the card even if its addition would exceed the SCCP TPS threshold. If the force=yes parameter is specified, the command is accepted but the following warning message appears:


WARNING: System current rated TPS unable to support additional SS7 card = use FORCE=YES.

If the force=yes parameter is specified, it is recommended that the required number of Service Module cards be added to the database after the LIM card is added. This action avoids the loss of GTT traffic. Another option is to add additional Service Module cards or to increase the SCCP TPS threshold, and then add the LIM card. This action prevents the alarm from being triggered.

For additional information on using the force parameter, see Chapter 4, "System Administration Procedures" of Database Administration - System Management User's Guide.

STC Cards

STC cards are E5-ENET-B cards that run the EROUTE application. E5-ENET-B cards provisioned with type=stc can be referred to as E5-STC cards.

The type=stc and appl=eroute parameters apply only when the EAGLE 5 Integrated Monitoring Support (E5IS) feature is turned on.

An "n+1" STC configuration is required to provide redundancy: therefore, a minimum of two STC cards must be provisioned in the EAGLE.

The EAGLE can contain a maximum of 32 STC cards.

The STC cards must be provisioned in the same shelf that contains the cards or links being monitored.

E5-SM8G-B/SLIC Cards

If an LNP feature quantity that is greater than 192 million numbers and less than 240 million numbers is present in a node, and there is an attempt to insert an E5-SM8G-B or SLIC card, then the card auto-inhibits (see the alw-card command).

IPSM Cards

IPSM cards consist of E5-IPSM and E5-ENET-B cards.

A maximum of three IPSM cards are supported for a single EAGLE node, on any shelf or combination of shelves.

Apart from these, two more cards with application type IPS can be configured on E5-ENET-B cards for the SS7 Firewall Logging feature.

IPSG Cards

IPSG cards consist of E5-ENET-B, or SLIC cards running the IP Signaling Gateway application (type=enet, enetb or slic, and appl=ipsg). The IPSG application combines the functionality of IPLIMx M2PA and IPGWx M3UA. They can also have GTT-enabled capabilities support with SLIC running the 64-bit IPSG GPL.

If an E5-ENET-B card is inserted in a slot provisioned for SLIC, then the E5-ENET-B card will be auto-inhibited and issue a degraded mode alarm.

E5-ATM-B Cards

E5-ATM-B cards support ANSI and ITU implementations. The cards can support 3 ATM signaling links, operating at 1 Erlang.

IP Signaling Capacity Guidelines

System limits on the total number of cards allowed in the system are not enforced by the ent-card command. If the HIPR2 High Rate Mode feature is turned off, then the total IP Signaling TPS for the system must be less than or equal to 500,000 TPS. If the HIPR2 High Rate Mode feature is turned on, then the total IP Signaling TPS for the system must be less than or equal to 750,000 TPS. If the HIPR2 High Rate Mode and 1M System TPS features are turned on, then the total IP Signaling TPS for the system must be less than or equal to 1,000,000 TPS.

E5-TSM Cards

A maximum of eight E5-TSM cards are supported for a single EAGLE node, on any shelf or combination of shelves, to support the GLS application for Gateway Screening.

Fast Copy Cards

E5-ENET-B, or SLIC cards running the IPSG or IPGHC GPL are considered to be FC- capable. A card running the IPGHC GPL must be in the IS-NR State before the card can be considered FC- capable. This restriction does not apply to cards running the IPSG GPL. An FC- capable card is considered FC- enabled when Fast Copy monitoring is enabled for the respective GPL.

Service Module Cards

Service Module cards consist of E5-SM8G-B or SLIC cards.

If the ent-card command is issued while an EPAP-based feature is enabled, then a warning is issued only for the provisioning of the 26th Service Module card. The command must be re-entered within 30 seconds to be accepted. If the command is entered a second time with type=dsm and a different loc specified, the command will be rejected.

For Service Module applications (VSCCP, ENUMHC , SIPHC, DEIRHC), the ent-card command can be used to provision E5-SM4G and E5-SM8G-B cards only in even numbered slots and the next odd numbered slot has to be empty since these cards are dual slots. There is no such restriction with SLIC cards since it is a single slot card, as in, these applications can be provisioned either in even numbered slot or odd numbered slot.

E5-E1T1-B Cards

E5-T1T1-B cards support ANSI and ITU implementations and can be used to replace the cards.

Each E5-E1T1-B card provides access to eight E1/T1 ports. Each card supports up to two SE-HSL signaling links on one of the eight ports (links A or B).

EPM and EPM-B Based Cards

Release 44.0 introduces the E5-ATM-B, E5-ENET-B, and E5-MCPM-B cards and Release 45.0 introduces the E5-E1T1-B card, which are all based on a new EPM-B. If the Message Flow Control option is provisioned (see the chg-stpopts command), and fan trays are installed, then the EPM-B cards can co-exist and be hot-swapped with the EPM cards. The E5-ENET-B and SLIC card running the IPS application and the E5-MCPM-B card do not require Message Flow Control, except for cards configured as SFLOG.

Service and Link Interface Cards

Release 46.3 introduced the EAGLE's Service and Link Interface Card (SLIC). These cards are the next generation, general purpose EAGLE processors and can be installed in any EAGLE shelf equipped with fan trays. In Release 46.3 the SLIC card supports the IPSG application and is hot-swappable with E5-ENET-B cards. In Release 46.5, the SLIC card supports VSCCP, SIPHC, ENUMHC, DEIRHC, CCS7ITU and SS7ANSI applications.

MCPM Cards

E5-MCPM-B cards are the MCPM cards. These cards are used to perform Measurements collection and reporting functionality for nodes with a link capacity greater than 2,400 (1,200 if 15 Minute Measurements is enabled). E5-OAM Integrated Measurements is used for nodes with a link capacity of 2400/1200 or less.

E5-APP-B Cards

E5-APP-B cards support the ELAP, EPAP, IMF, LSMS and NAS applications. E5-APP-B card is dual-slot card. These cards host the EPAP, ELAP, IMF, LSMS and NAS application servers that can be placed in any odd numbered slot in any EAGLE shelf. These cards do not connect to the IMT bus. The ENT-CARD command only reserves a slot in an EAGLE shelf for this card. An E5-APP-B card cannot be provisioned if there is another E5-APP-B card already on the same source of power unless the force parameter is specified.

TELCO Switches

Telco Switches are not application cards. The support of Telco Switches is added in the ENT-CARD command to reserve a slot in an Eagle shelf (type=FPB) and add the power consumed by Telco Switch to the Frame Power Budget. These switches will not be connected to the IMT bus. Telco Switch and E5-APP-B cards will be mutually exclusive for a shelf. There can be a maximum of 6 Telco Switches in a shelf.

Output


		  ent-card:loc=1206:type=lime1:appl=ss7ansi


   rlghncxa03w 06-06-01 11:11:28 EST  EAGLE 35.0.0
   ENT-CARD: MASP A - COMPLTD 
;

ent-card:loc=1101:type=dsm:appl=siphc

tekelecstp 12-07-27 10:24:14 EST EAGLE 45.0.0
ent-card:loc=1101:type=dsm:appl=siphc
Command entered at terminal #4.
ENT-CARD: MASP A - COMPLTD
;

This example shows the output when the ent-card command is not re-issued within 30 seconds for the provisioning of 26th SCCP card when any EPAP based feature is enabled.

 ent-card:type=dsm:appl=vsccp:loc=1306


    tekelecstp 10-02-27 23:06:21 EST  EAGLE 42.0.0
    ent-card:type=dsm:appl=vsccp:loc=1306
    Command entered at terminal #1. 
;
    
    CAUTION: Please ensure EPAP Application Server is running on 
    hardware supporting 32 SCCP cards e.g.: T1200.                                                          
    Re-enter command within 30 seconds to confirm change.
    
    tekelecstp 10-02-27 23:06:21 EST  EAGLE 42.0.0
    ENT-CARD: MASP B - Command Aborted
        
> Command is not re-entered within 30 seconds.
    
    ENT-CARD command (Type=DSM) confirmation timer expired

This example shows the output when the ent-card command is re-issued within 30 seconds for the provisioning of 26th SCCP card when any EPAP based feature is enabled.

 ent-card:type=dsm:appl=vsccp:loc=1306


    tekelecstp 10-02-27 23:07:16 EST  EAGLE 42.0.0
    ent-card:type=dsm:appl=vsccp:loc=1306
    Command entered at terminal #1. 
;
          
    CAUTION: Please ensure EPAP Application Server is running on
    hardware supporting 32 SCCP cards e.g.: T1200.                                                             
    Re-enter command within 30 seconds to confirm change.
    
    tekelecstp 10-02-27 23:07:16 EST  EAGLE 42.0.0
    ENT-CARD: MASP B - Command Aborted 

> ent-card command is re-issued within 30 seconds. 

> ent-card:type=dsm:appl=vsccp:loc=1306 

Command Accepted - Processing

    tekelecstp 10-02-27 23:07:28 EST  EAGLE 42.0.0
    ent-card:type=dsm:appl=vsccp:loc=1306
    Command entered at terminal #1. 
;

    tekelecstp 10-02-27 23:07:28 EST  EAGLE 42.0.0
    ENT-CARD: MASP B - COMPLTD 
;

This example shows the output when the ent-card command is issued for the provisioning of any additional (>26 and <=32) SCCP card when any EPAP based feature is enabled.

 ent-card:type=dsm:appl=vsccp:loc=1307


    tekelecstp 10-02-27 23:11:18 EST  EAGLE 42.0.0
    ent-card:type=dsm:appl=vsccp:loc=1307
    Command entered at terminal #1. 
;

    tekelecstp 10-02-27 23:11:18 EST  EAGLE 42.0.0
    ENT-CARD: MASP B - COMPLTD 
;

ent-card:loc=1105:type=e5appb:appl=epap:srvname=tklcepap1

    

tekelecstp 12-07-13 11:42:29 EST  45.0.0-64.37.0
    ent-card:loc=1105:type=e5appb:appl=epap:srvname=tklcepap1
    Command entered at terminal #4.
    ENT-CARD: MASP A – COMPLTD
;

ent-card:loc=1103:type=e5appb:appl=elap:srvname=tklcelap1


tekelecstp 12-07-13 11:42:55 EST  45.0.0-64.37.0
    ent-card:loc=1103:type=e5appb:appl=elap:srvname=tklcelap1
    Command entered at terminal #4.
    ENT-CARD: MASP A – COMPLTD

ent-card:loc=1101:type=e5appb:appl=epap:srvname=tklcepap2

    

tekelecstp 12-07-13 11:43:29 EST  45.0.0-64.37.0
    ent-card:loc=1101:type=e5appb:appl=epap:srvname=tklcepap2
    Command entered at terminal #4.
Command Rejected: E2667 - Same Power source of E5APPB cards running same application

    ENT-CARD: MASP A - Command Aborted

This example shows the output when the ent-card command is issued for provisioning the 1st TELCO Switch in a shelf.

ent-card:loc=6201:type=telco:appl=switch:srvname=telco1
tekelecstp 12-09-06 10:58:45 EST 45.0.0
ent-card:loc=6201:type=telco:appl=switch:srvname=telco1
Command entered at terminal #4.

WARNING: Minimum two TELCO Switches are needed per shelf.

ENT-CARD: MASP A - COMPLTD.
;

This example shows the output when the ent-card command is issued for the provisioning the 7th TELCO Switch in a shelf.

ent-card:lock=6211:type=telco:appl=switch:srvname=telco11


tekelecstp 12-09-06 11:01:50 EST 45.0.0
ent-card:loc=6211:type-telco:appl=switch:srvname=telco11
Command entered at terminal #4.
Command Rejected: E2678 - Maximum 6 TELCO Switches can be provisioned in a shelf

ENT-CARD: MASP A - Command Aborted


			 ent-card:loc=1101:type=dsm:appl=siphc

    
tekelecstp 12-07-27 10:24:47 EST EAGLE 45.0.0
    ent-card:loc=1101:type=dsm:appl=siphc
    Command entered at terminal #4.
    ENT-CARD: MASP A - COMPLTD
;

This example shows the output to configure an E5-SM8G-B or SLIC card running the DEIRHC GPL.

ent-card:loc=1103:type=dsm:appl=deirhc

    
tekelecstp 13-04-5 10:24:47 EST EAGLE 45.1
    ent-card:loc=1103:type=dsm:appl=deirhc
    Command entered at terminal #4.
    ENT-CARD: MASP A - COMPLTD
;

This example shows the output to configure a logging card running the IPSHC GPL.

ent-card:loc=1111:type=ipsm:appl=ips:sflog=yes


tekelecstp 15-05-27 14:56:16 EST  Eagle 46.3.0
    ent-card:loc=1111:type=ipsm:appl=ips:sflog=yes
    Command entered at terminal #4.
    ENT-CARD: MASP A - COMPLTD
;

This example shows the output to configure a SLIC card running the IPSG GPL.

ent-card:loc=1101:type=slic:appl=ipsg

Command Accepted - Processing

    tekelecstp 17-04-20 14:28:49 EST  EAGLE 46.6.0.0.0-71.1.0
    ent-card:loc=1101:type=slic:appl=ipsg
    Command entered at terminal #1.
;
    tekelecstp 17-04-20 14:28:49 EST  EAGLE 46.6.0.0.0-71.1.0
    ENT-CARD: MASP A - Cannot access standby fixed disk.
    ENT-CARD: MASP A - Simplex database update.
    ENT-CARD: MASP A - COMPLTD
;

This example shows the output when DATA parameter is specified with an ENETB card running the IPSG appl:

ent-card:loc=1101:type=enetb:appl=ipsg:data=gtt

tekelecstp 17-05-22 11:20:29 EST EAGLE 46.6
    ent-card:loc=1101:type=enetb:appl=ipsg:data=gtt
    Command entered at terminal #4.
Command Rejected: E3540 – DATA parm can be enteredspecified for IPSG appl running on SLIC card only.

    ENT-CARD: MASP A - Command Aborted

This example shows the output to configure a SLIC card running the SCCPHC GPL.

ent-card:loc=1105:type=slic:appl=vsccp

Command Accepted - Processing

    e9021503 18-03-22 12:47:26 EST  EAGLE 46.5.1.0.0-70.40.0
    ent-card:loc=1105:type=slic:appl=vsccp
    Command entered at terminal #2.
;

    e9021503 18-03-22 12:47:27 EST  EAGLE 46.5.1.0.0-70.40.0
*C  8446.0331 *C SCCP SYSTEM             SCCP is not available
;

    e9021503 18-03-22 12:47:27 EST  EAGLE 46.5.1.0.0-70.40.0
    ENT-CARD: MASP B - COMPLTD

This example shows the output to configure a SLIC card running the SFAPP GPL:

ent-card:loc=1108:type=slic:appl=sfapp

tekelecstp 17-11-13 04:40:52 EST  EAGLE 46.5.1.5.0-73.2.0
    ent-card:loc=1108:type=slic:appl=sfapp
    Command entered at terminal #17.
;

Command Accepted - Processing
    tekelecstp 17-11-13 04:40:52 EST  EAGLE 46.5.1.5.0-73.2.0
    ENT-CARD: MASP A - COMPLTD
;
Command Executed

4.284 ent-card