Installing and Removing SFP+ Optical Transceiver Modules

Language:

This section describes how to install and remove SFP+ optical transceiver modules to and from the SFP+ cages on the universal HBA. You might need to perform these procedures if you want to replace the PCI bracket on the universal HBA (see To Replace the PCI Bracket), or if you want to change the configuration of the universal HBA (see Universal HBA Features and Specifications and Determining and Changing the Current Operating Protocol Mode). After making these changes, you can install the hardware into the system, as described in To Install the Universal HBA.

This section contains the following topics:

To Install an SFP+ Optical Transceiver Module

To change the configuration of the universal HBA, the first step is to connect an SFP+ optical transceiver module to one of the SFP+ cages of the universal HBA. The functionality of the universal HBA changes, based on the optical transceiver module that you install and based on your manual configuration (described in a later chapter). The supported transciever modules follow:

16 Gb FC SFP+ SW Optic Modules, QLogic (Oracle part number: 7101676) – Enables 16 Gb FC HBA functionality.
10 GbE FCoE SR XCVR Modules, QLogic (Oracle part number: 7101678) – Enables 10 GbE FCoE Converged Network Adapter functionality.
Sun Storage 16 Gb FC SFP+ LW Optic Modules, QLogic (Oracle part number: 7101680) – Enables 16 Gb FC HBA functionality.

Note - Only supported transceiver modules are allowed. If invalid or unapproved transceivers are installed and the board is booted, unpredictable performance results could occur, and the board will no longer be supported until you replace the invalid transcievers with the supported transceivers.

Follow these guidelines whenever you install or remove an SFP+ module:

Do not remove the dust plugs from the modules or the rubber caps from the fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the module ports and cables from contamination and ambient light.
Removing and installing an SFP+ module can shorten its useful life. Do not remove and insert any module more often than is absolutely necessary.
To prevent ESD damage, follow the guidelines listed in Observing ESD and Handling Precautions.

If the SFP+ cages on the universal HBA are not empty, refer to To Remove an SFP+ Optical Transceiver Module for instructions on removing the modules or copper cables from the universal HBA. Then, follow the steps below to install each optical module in the universal HBA:

Remove the SFP+ optical transceiver module from its packaging.

Remove the protective end cap.

Pull the locking handle into the full horizontal position until you feel the handle click into position.

Holding the SFP+ module by the edges, align the SFP+ module with the slot in the universal HBA and slide the module into the opening.

Applying even pressure at both corners of the SFP+ module, push the module until it is firmly seated in the slot.
You will hear a click when the module is firmly seated in the slot.

Lift the locking handle up and push it closed to lock the SFP+ module in place.
If you do not plan to connect cables immediately, replace the dust covers or caps.

Note - If you pull the locking handle down when the optical transceiver module is installed, you must remove the module entirely and reinstall it. The handle operates an internal lock. Pulling the handle down can disconnect the optical transceiver module, even though it may appear to be connected.

Continue to To Install the Universal HBA.

To Remove an SFP+ Optical Transceiver Module

Disconnect the optical cable from the SFP+ optical transceiver cage of the universal HBA.

Pull the locking handle down into the full horizontal position to unlock the module.

Grasp the module by both corners and pull the SFP+ module to disengage it from the SFP+ cage.

Pull the module out until it is free of the slot.

Insert a protective end cap into the optical cage of the SFP+ module.

Push the locking handle back into its vertical position.

Place the module in its original packaging, antistatic bag, or other protective environment.