Determining and Changing the Operating Protocol Mode Using the QConvergeConsole CLI

Language:

Note - For detailed information on installing the QConvergeConsole CLI utility, see the QConvergeConsole CLI User's Guide.

The QLogic QConvergeConsole command-line interface (CLI) utility is used to configure and manage QLogic Fibre Channel adapters, Intelligent Ethernet adapters, and converged network adapters within SANs. The QConvergeConsole CLI has two modes of operation: noninteractive mode and interactive mode.

Noninteractive mode uses a CLI, in which you type a complete command-line with switches and associated settings at the operating system prompt. Interactive mode uses a menu-driven interface that prompts you to select information from menus to perform the desired operation.

Note - The QConvergeConsole CLI is case-sensitive.

To Determine and Change the Operating Protocol Mode Using the QConvergeConsole Noninteractive CLI

Follow these instructions to determine and change the operating protocol mode of the universal HBA using the QConvergeConsole CLI in noninteractive mode in the Windows, Linux, or Oracle Solaris OS.

Open an operating system shell.

(Optional) Issue the following command to display the current operating protocol mode of the universal HBA:
qaucli -pc hba-instance --info

Where hba-instance is the HBA instance number of the universal HBA. To discover the instance number of the universal HBA, you can issue the -g command.

Issue the following command to change the operating protocol mode of the universal HBA:
qaucli -pc hba-instance --type mode

Where:

hba-instance is the HBA instance number of the universal HBA. To discover the instance number of the universal HBA, you can issue the -g command.

mode is one of the following:
- - fco or 0 to change the operating protocol mode to Fibre Channel only.
  - cna or 1 to change the operating protocol mode to CNA.
  Note - You need to perform this procedure on only one port (or, instance) of the universal HBA.

Repeat step 1 through step 3 for all universal HBAs, and then perform a full power reboot of the system in which the universal HBAs are installed.
Note - For systems that have hot-plug/hot swap capability, instead of initiating a full power reboot of the system, you can perform a hot-plug out and hot-plug in of the card.

To Determine and Change the Operating Protocol Mode Using the QConvergeConsole Interactive CLI

Follow the instructions in this section to determine and change the operating protocol mode of the universal HBA using the QConvergeConsole CLI in interactive mode.

Note - The examples in this procedure are for a universal HBA in FC-only mode. Any additional steps that are required for a universal HBA in CNA mode are noted in the procedure.

Start the QConvergeConsole CLI in interactive mode using the method specified below for your operating system:
- Windows – Do one of the following:
  - Double-click the QConvergeConsole CLI icon on the desktop.
  - Click Start, point to All Programs, point to QLogic Management Suite, and then click QConvergeConsole CLI.
  - Open a command prompt in the installation directory (the default is: C:\Program Files\QLogic Corporation\QConvergeConsoleCLI), and then issue the following command: qaucli
- Linux – Issue the following command: qaucli
- Oracle Solaris – Issue the following command: qaucli
The Main Menu appears:
```
 Main Menu
 1:  Adapter Information
 2:  Adapter Configuration
 3:  Adapter Updates
 4:  Adapter Diagnostics
 5:  Adapter Statistics
 6:  Refresh
 7:  Help
 8:  Exit
 
 Please Enter Selection: 
```

In CNA mode, type 1 or in FC mode, type 2 to select the Adapter Configuration menu option.
```
 Main Menu
 1:  Adapter Information
 2:  Adapter Configuration
 3:  Adapter Updates
 4:  Adapter Diagnostics
 5:  Adapter Statistics
 6:  Refresh
 7:  Help
 8:  Exit
 
 Please Enter Selection: 2
```
When the universal HBA is in FC mode, the Adapter Configuration menu
The menu title is “FCoE Converged Network Adapter (CNA) Configuration” if the current personality of the universal HBA is CNA.
appears with the menu options shown in the following step.

At the Adapter Configuration menu, type 13 to select the Personality (operating protocol mode) menu option
```
 Fibre Channel Adapter Configuration
 1:  Adapter Alias
 2:  Adapter Port Alias
 3:  HBA Parameters
 4:  Target Persistent Binding
 5:  Boot Devices Configuration
 6:  Virtual Ports (NPIV)
 7:  Target Link Speed (iiDMA)
 8:  Driver Parameters
 9:  Selective LUNs
10:  QoS
11:  Export (Save) Configuration
12:  Generate Reports
13:  Personality
(p or 0: Previous Menu; m or 98: Main Menu; ex or 99: Quit)
Please Enter Selection:13
```
Note - If the universal HBA is in CNA mode, additional selections appear on the Main Menu. If in CNA mode, type 1 at the Main Menu to select CNA Configuration, and then type 1 again to select the CNA FCoE Configuration menu option. This takes you to the Converged Network Adapter (CNA) FCoE Configuration menu. At this point, you would type 11, instead of 13 as described in this step.

The Adapter Selection menu
The displayed information reflects a CNA if the current personality of the universal HBA is CNA.
appears.

To select the universal HBA, type the number of the universal HBA.
In the following example, the only universal HBA is number 1:
```
1: HBA Model: QLE8362 SN: AFE1224F05264
      Port   2 WWPN: 21-00-00-0E-1E-08-F2-11 SFP not installed
      Port   1 WWPN: 21-00-00-0E-1E-08-F2-10 SFP not installed
(p or 0: Previous Menu; m or 98: Main Menu; ex or 99: Quit)
Please Enter Selection: 1
```
A prompt appears to verify the personality change
This prompt is “Change personality to FC Only?” if the current personality of the universal HBA is CNA.
.

At the prompt, type y to accept, or n to cancel.
```
Change personality to CNA? (y/n): y
```
A message confirms the change.

Follow the instructions in the message to complete the operating protocol mode change for the universal HBA.
The following is an example of an instructional message:

Personality type of HBA instance 1 (QLE8362) has been changed successfully. Please power cycle machine. Make sure to change the SFP module to a compatible one (FC) before reboot.

Note - For systems that have hot-plug/hot swap capability, instead of initiating a full power reboot of the system, you can perform a hot-plug out and hot-plug in of the card.