Sun Blade 6048 Modular System Service Manual
820-2863-13
Contents |
1. Introduction to the Sun Blade 6048 Modular System
1.4.1 CMM Integrated Lights Out Manager (ILOM) Features
1.4.2 Sun Integrated Lights Out Manager
1.6 Reliability, Availability, and Serviceability Features
1.6.1 Hot-Pluggable Components
1.6.2 Hot-Swappable Components
1.6.4 Environmental Monitoring
1.6.6 LED Indicators and Buttons
View Component Information Using the CLI
View Component Information Using the Web Interface
2.1.1 External Compared With Internal Faults
2.1.2 Components Monitored by Fault Management
2.2.1 Monitoring the Service Action Required LEDs
2.2.1.1 When Service Action Required LEDs Are Turned Off
2.2.1.2 When Only the Chassis Shelf LEDs Are Lit
2.2.1.3 About Power Supply Faults
2.2.2 Monitoring Faults From the Management Interfaces
2.2.2.1 Obtaining Sensor Readings Using the CLI
2.2.2.2 Obtaining Sensor Readings Using the Web Interface
2.2.3 Monitoring the Event Log
2.2.3.1 Viewing or Clearing the ILOM Event Log Using the CLI
2.2.3.2 Viewing or Clearing the ILOM Event Log Using the Web Interface
2.3 Determining That Hardware Has Failed
2.3.1.1 Chassis Shelf LED Locations
2.3.1.3 Viewing Chassis Shelf Faults in ILOM
2.3.2 Power Supply Module Faults
2.3.2.1 Power Supply LED Locations
2.3.2.2 Power Supply Fault LED Functions
2.3.2.3 Viewing Power Supply Faults in ILOM
2.3.3.2 Rear Fan Fault LED Functions
2.3.3.3 Viewing Rear Fan Faults in ILOM
2.4 Replacing a Faulted Component
3.1 About Replaceable Components
3.1.1 Accessing Component Information
3.1.2 Diagnosing and Detecting Component Faults
3.1.3 Hot-Swappable and Hot-Pluggable Components
3.2 Locating Front and Rear Components
3.3 Powering Off the System Before Service
3.3.1 Powering Off the System Using the CLI
3.3.2 Powering Off the System Using the Web Interface
3.4 Required Installation Tools and ESD
3.4.0.1 Attaching the Antistatic Wrist Strap
4. Replacing System Components
4.1 Customer-Replaceable Units
4.1.1 Replacing Power Supplies and Front Fan Modules
4.1.1.1 Removing the Power Supply Modules and Front Fan Modules
4.1.1.2 Installing the Power Supply Modules and Front Fan Modules
4.1.2 Replacing Server Modules
4.1.2.1 Removing Server Modules
4.1.2.2 Installing Server Modules
4.1.3 Replacing the Front Indicator Module
4.1.3.1 Removing the Front Indicator Module
4.1.3.2 Installing the Front Indicator Module
4.1.6 Replacing the Rear Fan Modules
4.1.6.1 Removing the Rear Fan Modules
4.1.6.2 Installing Rear Fan Modules
4.1.7.1 Removing the Fan Board
4.1.7.2 Installing a Fan Board
4.1.9 Installing the Cooling Doors
4.2.1.2 Installing the Midplane
4.3 Servicetool FRU Update Procedure
4.4 Powering On the System After Service
4.4.2 Powering On the System Automatically
4.4.3 Powering On the System Using the CLI
4.4.4 Powering On the System Using the Web Interface
4.5 Expansion Module Installation
4.6 Floor Tie Down Installation
A. Sun Blade 6048 ILOM 2.0 Information
A.1 Activating CMM Ethernet Ports
A.1.1 To Enable Ethernet Ports Through the CLI
A.1.2 To Enable Ethernet Ports Through the Web Interface
A.2 ILOM Behavior With Two Power Cord Configuration
A.3.6 Readings for Specific Cases
A.3.6.2 AC Cables Are Disconnected
A.3.6.3 All the AC Cables Get Disconnected, Then Plugged Back In
B.1 Determining Power Requirements
B.1.1 Power Required by the Chassis
B.1.2 Power Required by Blades
B.1.3 Power Estimates for Network Express Modules (NEMs)
B.1.4 Power Requirements for Fans
B.2 ILOM Power Management Features
Copyright © 2009 Sun Microsystems, Inc. All rights reserved.