This topic provides instructions to verify Oracle 1.6 TB NVMe SSD operation on the host for supported Oracle Solaris and Linux operating systems. Verify Oracle 1.6 TB NVMe SSD operation using Oracle Hardware Management Pack utility CLI tools.
Before You Begin
Verify that Oracle Hardware Management Pack is installed on the host.
Refer to the Oracle Hardware Management Pack documentation for instructions at: http://www.oracle.com/goto/ohmp/docs
Ensure that you have access to the server (either directly or over the network).
Verify that the Service Action Required 1.6 TB NVMe SSD status indicator is not lit and that the green Power status indicator is lit on the 1.6 TB NVMe SSDs that you updated. Green (operational), Amber (faulty disk ), Blue (SSD has been prepared for removal).
Refer to the Oracle 1.6 TB NVMe SSD User Guide.
For example, to log into the target system through SSH or through Oracle ILOM Remote System Console, do one of the following:
Type: ssh root@hostname, where hostname can be the DNS name or the IP address for the server host.
To establish a local connection to the host console, perform the following steps:
Launch an Oracle ILOM Remote System Console Plus session.
For instructions, see Launching Remote KVMS Redirection Sessions in the server administration guide.
You issue Oracle Hardware Management Pack commands from the operating system command-line interface.
# fwupdate list controller
In the following example, devices are enumerated in the output returned by the above command.
# fwupdate list controller ================================================== CONTROLLER ================================================== ID Type Manufacturer Model Product Name FW Version BIOS Version EFI Version FCODE Version Package Version NVDATA Version XML Support ------------------------------------------------------------------------------- c0 SAS LSI Logic 0x0097 SAS9311-8i 06.00.02.00 08.13.00.00 07.00.00.00 01.00.65.00 - 06.03.00.10 N/A c1 NVMe Intel 0x0953 INTEL SSDPE2ME016T4S 8DV1RA12 c2 NVMe Intel 0x0953 INTEL SSDPE2ME016T4S 8DV1RA12
In the above example, 1.6 TB NVMe SSD controllers c1 and c2 are enumerated in the output returned by the above command.
See Minimum Supported Oracle 1.6 TB NVMe SSD Firmware Version.
To identify NVMe controllers and current firmware versions type:
# nvmeadm list -v
To identify NVMe controllers that have updated firmware, view the Firmware Revision: row in the output from the nvmeadm list -v command.
In the following example, controller F160-NVME-1 and F160-NVME-1 show firmware version 8DV1RA12 in the output returned by the above command.
# nvmeadm list -v F160-NVME-1 PCI Vendor ID: 8086 Serial Number: CVMD446000AQ1P6KGN Model Number: INTEL SSDPE2ME016T4S Firmware Revision: 8DV1RA12 Number of Namespaces: 1 F160-NVME-2 PCI Vendor ID: 8086 Serial Number: CVMD446000CF1P6KGN Model Number: INTEL SSDPE2ME016T4S Firmware Revision: 8DV1RA12 Number of Namespaces: 1 root:~#
To check the selected 1.6 TB NVMe SSD health and SMART information, type:
# nvmeadm getlog -h
Ensure the 1.6 TB NVMe SSDs have remaining drive life in the output returned by the above command.
# nvmeadm getlog -h F160-NVME-1 SMART/Health Information: Critical Warning: 0 Temperature: 312 Kelvin Available Spare: 100 percent Available Spare Threshold: 10 percent Percentage Used: 0 percent Data Unit Read: 0x1 of 512k bytes. Data Unit Written: 0x0 of 512k bytes. Number of Host Read Commands: 0x30313b3 Number of Host Write Commands: 0x302f25d Controller Busy Time in Minutes: 0x0 Number of Power Cycle: 0xf Number of Power On Hours: 0x1c Number of Unsafe Shutdown: 0xf Number of Media Errors: 0x0 Number of Error Info Log Entries: 0x0 F160-NVME-2 SMART/Health Information:....