Adding Local File Systems to a Specific Zone-Cluster Node

Language:

This section describes how to add file systems that are dedicated to a single zone-cluster node. To instead configure file systems for use by the entire zone cluster, go to Adding File Systems to a Zone Cluster.

This section contains the following procedures:

How to Add a Local File System to a Specific Zone-Cluster Node (CLI)

Perform this procedure to add a local file system to a single, specific zone-cluster node of a specific zone cluster. The file system is not managed by Oracle Solaris Cluster software but is instead passed to the underlying Oracle Solaris zone.

Note - To add a highly available local file system to a zone cluster, perform procedures in How to Add a Highly Available Local File System to a Zone Cluster (clsetup) or How to Add a Highly Available Local File System to a Zone Cluster (CLI).

Assume the root role on a node of the global cluster that hosts the zone cluster.
Note - Perform all steps of this procedure from a node of the global cluster.
Create the local file system that you want to configure to a specific zone-cluster node.
Use local disks of the global-cluster node that hosts the intended zone-cluster node.

Add the file system to the zone-cluster configuration in the node scope.

phys-schost# clzonecluster configure zoneclustername
clzc:zoneclustername> select node physical-host=baseclusternode
clzc:zoneclustername:node> add fs
clzc:zoneclustername:node:fs> set dir=mountpoint
clzc:zoneclustername:node:fs> set special=disk-device-name
clzc:zoneclustername:node:fs> set raw=raw-disk-device-name
clzc:zoneclustername:node:fs> set type=FS-type
clzc:zoneclustername:node:fs> end
clzc:zoneclustername:node> end
clzc:zoneclustername> verify
clzc:zoneclustername> commit
clzc:zoneclustername> exit

dir=mountpoint: Specifies the file-system mount point
special=disk-device-name: Specifies the name of the disk device
raw=raw-disk-device-name: Specifies the name of the raw-disk device
type=FS-type: Specifies the type of file system

Note - Enable logging for UFS file systems.

Verify the addition of the file system.

phys-schost# clzonecluster show -v zoneclustername

Example 6-5 Adding a Local File System to a Zone-Cluster Node (CLI)

This example adds a local UFS file system /local/data for use by a node of the sczone zone cluster. This zone-cluster node is hosted on global—cluster node phys-schost-1.

phys-schost-1# clzonecluster configure sczone
clzc:sczone> select node physical-host=phys-schost-1
clzc:sczone:node> add fs
clzc:sczone:node:fs> set dir=/local/data
clzc:sczone:node:fs> set special=/dev/md/localdg/dsk/d1
clzc:sczone:node:fs> set raw=/dev/md/localdg/rdsk/d1
clzc:sczone:node:fs> set type=ufs
clzc:sczone:node:fs> add options [logging]
clzc:sczone:node:fs> end
clzc:sczone:node> end
clzc:sczone> verify
clzc:sczone> commit
clzc:sczone> exit

phys-schost-1# clzonecluster show -v sczone
…
--- Solaris Resources for phys-schost-1 ---
…
Resource Name:                                fs
dir:                                           /local/data
special:                                       /dev/md/localdg/dsk/d1
raw:                                           /dev/md/localdg/rdsk/d1
type:                                          ufs
options:                                       [logging]
cluster-control:                               false ...

How to Add a Local ZFS Storage Pool to a Specific Zone-Cluster Node (CLI)

Perform this procedure to add a local ZFS storage pool to a specific zone-cluster node. The local ZFS pool is not managed by Oracle Solaris Cluster software but is instead passed to the underlying Oracle Solaris zone.

Note - To add a highly available local ZFS pool to a zone cluster, see How to Add a Highly Available Local File System to a Zone Cluster (clsetup) or How to Add a ZFS Storage Pool to a Zone Cluster (CLI).

Perform all steps of the procedure from a node of the global cluster.

Assume the root role on a node of the global cluster that hosts the zone cluster.
Create the local ZFS pool that you want to configure to a specific zone-cluster node.
Use local disks of the global-cluster node that hosts the intended zone-cluster node.

Add the pool to the zone-cluster configuration in the node scope.

phys-schost# clzonecluster configure zoneclustername
clzc:zoneclustername> select node physical-host=baseclusternode
clzc:zoneclustername:node> add dataset
clzc:zoneclustername:node:dataset> set name=localZFSpoolname
clzc:zoneclustername:node:dataset> end
clzc:zoneclustername:node> end
clzc:zoneclustername> verify
clzc:zoneclustername> commit
clzc:zoneclustername> exit

set name=localZFSpoolname: Specifies the name of the local ZFS pool

Verify the addition of the ZFS pool.

phys-schost# clzonecluster show -v zoneclustername

Example 6-6 Adding a Local ZFS Pool to a Zone-Cluster Node (CLI)

This example adds the local ZFS pool local_pool for use by a node of the sczone zone cluster. This zone-cluster node is hosted on global—cluster node phys-schost-1.

phys-schost-1# clzonecluster configure sczone
clzc:sczone> select node physical-host=phys-schost-1
clzc:sczone:node> add dataset
clzc:sczone:node:dataset> set name=local_pool
clzc:sczone:node:dataset> end
clzc:sczone:node> end
clzc:sczone> verify
clzc:sczone> commit
clzc:sczone> exit

phys-schost-1# clzonecluster show -v sczone
…
--- Solaris Resources for phys-schost-1 ---
…
Resource Name:                                dataset
name:                                          local_pool