Figures

FIGURE 1-1 Typical Netra CP2500 Board

FIGURE 1-2 Netra CP2500 Boards Installed in Netra CT 410 and 810 Servers

FIGURE 1-3 Netra CP2500 Board Diskless Client Configuration Example

FIGURE 1-4 Netra CP2500 Node Board Mounting Configuration Example

FIGURE 1-5 Netra CP2500 RTM-H for Netra CT Server Host Slots

FIGURE 1-6 Netra CP2500 RTM-S for Netra CT Satellite Slots and cPSB Node Slots

FIGURE 1-7 Netra CP2500 Board and a RTM-S in a Typical cPSB Chassis

FIGURE 1-8 Netra CP2500 Board Layout

FIGURE 1-9 Typical Netra CP2500 Board - Solder Side

FIGURE 1-10 Netra CP2500 Board Front Panel

FIGURE 1-11 Netra CP2500 Board Functional Block Diagram

FIGURE 1-12 Typical Netra CP2500 Board Barcode Labeling

FIGURE 2-1 PMC Slot Location

FIGURE 2-2 Removing the PMC Filler Panel

FIGURE 2-3 Inserting the PMC Into the PMC Slot

FIGURE 2-4 Pressing the PMC Into the PMC Connectors - Side View

FIGURE 2-5 Securing the PMC Screws

FIGURE 2-6 Setting the SW3301 Switch 2 to cPSB Chassis Operation

FIGURE 2-7 Replacing the SEEPROM

FIGURE 2-8 S1301 DIP Switch Bank Location on the RTM-S

FIGURE 2-9 Setting the S1301 DIP Switches for cPSB Networks

FIGURE 2-10 S1302 DIP Switch Bank Location on the Solder Side of the RTM-S

FIGURE 2-11 Setting the S1302 DIP Switches for cPSB Networks

FIGURE 2-12 Installing the Netra CP2500 Board and RTM-S in an cPSB Chassis

FIGURE 2-13 Installing a Netra CP2500 Board Into a cPSB Chassis Slot

FIGURE 2-14 Securing the Board in the Chassis Slot

FIGURE 3-1 Releasing the Netra CP2500 Ejector Levers

FIGURE 3-2 Blue Hot-Swap LED Location

FIGURE 4-1 Control Flow From Power On for Firmware

FIGURE 4-2 System Flash PROM Map

FIGURE 4-3 System Flash and User Flash Logical Devices on Same Physical Device

FIGURE 4-4 Setting Switch 1 on the SW3301 DIP Switch Bank to Closed

FIGURE 5-1 Loosening the Ejector Lever Captive Screws

FIGURE 5-2 Releasing the Netra CP2500 Ejector Levers

FIGURE 5-3 Blue Hot-Swap LED Location

FIGURE 5-4 Unlocking and Using the Ejector Levers to Remove the Board

FIGURE 5-5 Removing the SEEPROM

FIGURE 5-6 Loosening the PMC Device Screws

FIGURE 5-7 Lifting the PMC Device From the Board PMC Connectors

FIGURE 5-8 Replacing the PMC Filler Panel

FIGURE 5-9 Location of Memory Connectors

FIGURE 5-10 Removing a DIMM

FIGURE 5-11 Installing a DIMM Into a Board Memory Connector

FIGURE A-1 Physical Dimensions of the Netra CP2500 Front Panel

FIGURE A-2 Mechanical Dimensions of the Netra CP2500 Board

FIGURE B-1 Netra CP2500 Board PMC Port Connectors

FIGURE B-2 PMC Connector Slot Connector Pins

FIGURE B-3 Front Panel Serial Port Diagram

FIGURE B-4 Backplane Connector Contact Numbering

FIGURE B-5 SW3301 DIP Switch Location