| Netra CP2500 Board Installation and Technical Reference Manual |     |
| Netra CP2500 Board Installation and Technical Reference Manual | |
Netra CP2500 Board Installation and Technical Reference Manual
819-1747-11
|
Contents |
1. Netra CP2500 Board Overview
1.1 Netra CP2500 Board Features
1.2 Netra CP2500 Board System Configurations
1.5.2 Functional Block Diagram
1.6 Contacting Technical Support
2. Installing the Netra CP2500 Board in a cPSB Chassis
2.2 Equipment and Operator Safety
2.3 Materials and Tools Required
2.4 Preparing for the Installation
2.4.1 Checking Power, Thermal, Environmental, and Space Requirements
2.4.2 Determining Local Network IP Addresses and Hostnames
2.4.3 Installation Procedure Summary
2.5 Configuring the Board Hardware
2.5.1 Installing an Optional PMC Device
2.5.2 Setting the SW3301 DIP Switch
2.5.4 Preparing the RTM-S for Installation
2.5.4.1 Differences Between Available Netra CP2500 Rear Transition Modules
2.5.4.2 Setting RTM-S DIP Switches
2.6 Installing Boards Into a cPSB Chassis
2.6.2 Installing the Netra CP2500 Board
2.7 Setting Up an Assembled Netra CP2500 Board
2.8 Initial Power On and Firmware Upgrade
2.8.3 Determining Firmware Versions
2.8.3.1 Determining Firmware Versions From OpenBoot PROM Prompt
2.8.3.2 Determining Firmware Versions From the Solaris Prompt
2.8.4 Upgrading the OpenBoot PROM and SMC Firmware
3. Configuring Netra CP2500 Board Software
3.1.1 Hot-Swapping the Netra CP2500 Board
3.1.2 Retrieving Device Information
3.3 Downloading and Installing SunVTS
4. Configuring and Using the Netra CP2500 Board Firmware
4.2 Firmware Configuration Variables
4.2.1 OpenBoot PROM Configuration Variables
4.3 System Flash PROM Memory Map
4.4 Environmental Monitoring Support at OpenBoot PROM
4.4.2 Reading the CPU Temperature Limits
4.5 System Management Controller (SMC) Firmware
4.7 Booting the Board Using the Backup OpenBoot PROM
4.7.1 Updating the OpenBoot PROM and SMC Firmware
4.8.1 Setting Diagnostic Levels
4.8.2 OpenBoot PROM On-Board Diagnostics
5. Removing and Replacing Board Hardware
5.2 Handling Equipment and Assembling Tools
5.3 Displaying the Solaris FRU ID
5.4 Removing and Replacing the Board From the Chassis
5.4.1 Removing the Board From the Chassis
5.4.2 Replacing the Board in the System
5.5 Removing and Replacing the SEEPROM
5.6 Removing and Replacing a PMC Device
5.7 Removing and Replacing Memory Modules
5.7.1 Removing DIMM Memory Modules
5.7.2 Installing Memory Modules
A.1 System Compatibility Specifications
A.3 PMC Interface Specifications
A.6 Environmental Specifications
A.8 Reliability and Availability Specifications
B. Connectors, Pinouts, and Switch Settings
B.1.1 PMC Connector Interfaces
B.2 Front Panel Serial Connector
B.3.1 CompactPCI J1/P1 Connector Pinouts
B.3.2 CompactPCI J1/P1 Signal Descriptions
B.3.3 CompactPCI J2/P2 Connector Pinouts
B.3.4 CompactPCI J2/P2 Signal Descriptions
B.3.5 CompactPCI J3/P3 Connector Pinouts
B.3.6 CompactPCI J3/P3 Signal Descriptions
B.3.7 CompactPCI J5/P5 Connector Pinouts
B.3.8 CompactPCI J5/P5 Signal Descriptions
| Netra CP2500 Board Installation and Technical Reference Manual | 819-1747-11 | |
Copyright © 2007, Sun Microsystems, Inc. All Rights Reserved.