Go to main content

Administering Resource Management in Oracle® Solaris 11.4

Exit Print View

Updated: August 2018
 
 

How Dynamic Resource Allocation Works

This section explains the process and the factors that the poold daemon uses to dynamically allocate resources.

About Available Resources

Available resources are considered to be all of the resources that are available for use within the scope of the poold process. The scope of control is at most a single Oracle Solaris instance.

On a system that has zones enabled, the scope of an executing instance of the poold daemon is limited to the global zone.

Determining Available Resources

Resource pools encompass all of the system resources that are available for consumption by applications.

For a single executing Oracle Solaris instance, a resource of a single type, such as a CPU, must be allocated to a single partition. There can be one or more partitions for each type of resource. Each partition contains a unique set of resources.

For example, a system with four CPUs and two processor sets can have the following setup:

pset 0: 0 1
pset 1: 2 3

where 0, 1, 2, and 3 after the colon represent CPU IDs. Note that the two processor sets account for all four CPUs. The same system cannot have the following setup because CPU 1 can appear in only one processor set at a time:

pset 0: 0 1
pset 1: 1 2 3

Resources cannot be accessed from any partition other than the partition to which they belong.

To discover the available resources, the poold daemon interrogates the active pools configuration to find partitions. All resources within all partitions are summed to determine the total amount of available resources for each type of resource that is controlled.

This quantity of resources is the basic figure that the poold daemon uses in its operations. However, there are constraints upon this figure that limit the flexibility that the daemon has to make allocations. For information about available constraints, see Configuration Constraints.

Identifying a Resource Shortage

The control scope for the poold daemon is defined as the set of available resources for which the daemon has primary responsibility for effective partitioning and management. However, other mechanisms that are allowed to manipulate resources within this control scope can still affect a configuration. If a partition should move out of control while the daemon is active, the daemon tries to restore control through the judicious manipulation of available resources. If the daemon cannot locate additional resources within its scope, then the daemon logs information about the resource shortage.

Determining Resource Utilization

The poold daemon typically spends the greatest amount of time observing the usage of the resources within its scope of control. This monitoring is performed to verify that workload-dependent objectives are being met.

For example, for processor sets, all measurements are made across all of the processors in a set. The resource utilization shows the proportion of time that the resource is in use over the sample interval. Resource utilization is displayed as a percentage from 0 to 100.

Identifying Control Violations

The directives described in Configuration Constraints and Objectives are used to detect the approaching failure of a system to meet its objectives. These objectives are directly related to workload.

    A partition that is not meeting user-configured objectives is a control violation. The two types of control violations are synchronous and asynchronous.

  • A synchronous violation of an objective is detected by the daemon in the course of its workload monitoring.

  • An asynchronous violation of an objective occurs independently of monitoring action by the daemon.

    The following events cause asynchronous objective violations:

  • Resources are added to or removed from a control scope.

  • The control scope is reconfigured.

  • The poold resource controller is restarted.

The contributions of objectives that are not related to workload are assumed to remain constant between evaluations of the objective function. Objectives that are not related to workload are only reassessed when a reevaluation is triggered through one of the asynchronous violations.

Determining Appropriate Remedial Action

When the resource controller determines that a resource consumer is short of resources, the initial response is that increasing the resources will improve performance.

Alternative configurations that meet the objectives specified in the configuration for the scope of control are examined and evaluated.

This process is refined over time as the results of shifting resources are monitored and each resource partition is evaluated for responsiveness. The decision history is consulted to eliminate reconfigurations that did not show improvements in attaining the objective function in the past. Other information, such as process names and quantities, are used to further evaluate the relevance of the historical data.

If the poold daemon cannot take corrective action, the condition is logged. For more information, see poold Daemon Logging Information.