To ensure continuous availability of the network to send or receive traffic, IPMP performs failure detection on the IPMP group's underlying IP interfaces. Failed interfaces remain unusable until they are repaired. Remaining active interfaces continue to function while any existing standby interfaces are deployed as needed.
Two types of probe-based failure detection:
No test addresses are configured (transitive probing).
Test addresses are configured.
The Oracle VM Server for SPARC software supports link-based IPMP with virtual network devices. You can configure the IPMP group to use link-based and probe-based failure detection when you configure an IPMP group with virtual network devices. For more information, see Oracle VM Server for SPARC 3.3 Administration Guide.
Probe-based failure detection consists of using ICMP probes to check whether an interface has failed. The implementation of this failure detection method depends on whether test addresses are used.
This failure detection method involves sending and receiving ICMP probe messages that use test addresses. These messages, also called probe traffic or test traffic, are sent over the interface to one or more target systems on the same local network. The in.mpathd daemon probes all of the targets separately through all the interfaces that have been configured for probe-based failure detection. If no replies are made in response to five consecutive probes on a given interface, the in.mpathd daemon considers the interface to have failed. The probing rate depends on the failure detection time (FDT). The default value for failure detection time is 10 seconds. However, you can tune the FDT in the IPMP configuration file. For instructions, see How to Configure the Behavior of the IPMP Daemon.
To optimize probe-based failure detection, you must set multiple target systems to receive the probes from the in.mpathd daemon. By having multiple target systems, you can better determine the nature of a reported failure. For example, the absence of a response from the only defined target system can indicate a failure either in the target system or in one of the IPMP group's interfaces. By contrast, if only one system among several target systems does not respond to a probe, then the failure is likely in the target system rather than in the IPMP group itself.
The in.mpathd daemon determines which target systems to probe dynamically. First, the daemon searches the routing table for target systems on the same subnet as the test addresses that are associated with the IPMP group's interfaces. If such targets are found, then the daemon uses them as targets for probing. If no target systems are found on the same subnet, then the daemon sends multicast packets to probe neighbor hosts on the link. The multicast packet is sent to the All Hosts multicast address, 184.108.40.206 in IPv4 and ff02::1 in IPv6, to determine which hosts to use as target systems. The first five hosts that respond to the echo packets are chosen as targets for probing. If the daemon cannot find routers or hosts that responded to the multicast probes, then the daemon cannot detect probe-based failures. In this case, the ipmpstat –i command reports the probe state as unknown.
You can use host routes to explicitly configure a list of target systems to be used by the in.mpathd daemon. For instructions, see Configuring Probe-Based Failure Detection.
With no test addresses, this method is implemented by using two types of probes:
ICMP probes are sent by the active interfaces in the IPMP group to probe targets that are defined in the routing table. An active interface is an underlying interface that can receive inbound IP packets that are addressed to the interface's link layer (L2) address. The ICMP probe uses the data address as the probe's source address. If the ICMP probe reaches its target and gets a response from the target, then the active interface is operational.
Transitive probes are sent by the alternate interfaces in the IPMP group to probe the active interface. An alternate interface is an underlying interface that does not actively receive any inbound IP packets.
For example, consider an IPMP group that consists of four underlying interfaces and one data address. In this configuration, outbound packets can use all of the underlying interfaces. However, inbound packets can only be received by the interface to which the data address is bound. The remaining three underlying interfaces that cannot receive inbound packets are the alternate interfaces.
If an alternate interface can successfully send a probe to an active interface and receive a response, then the active interface is functional, and by inference, so is the alternate interface that sent the probe.
For information about the packet format of transitive probes, see Appendix B, Packet Format of Transitive Probes, in Managing Network Datalinks in Oracle Solaris 11.3.
A group failure occurs when all of the interfaces in an IPMP group appear to fail at the same time. In this case, no underlying interface is usable. Also, when all of the target systems fail at the same time and probe-based failure detection is enabled, the in.mpathd daemon flushes all of its current target systems and probes for new target systems.
In an IPMP group that has no test addresses, a single interface that can probe the active interface is designated as a prober. This designated interface has both the FAILED flag and PROBER flag set. The data address is bound to this interface, which enables the interface to continue probing the target to detect recovery.
Link-based failure detection is always enabled, provided that the interface supports this type of failure detection.
To determine whether a third-party interface supports link-based failure detection, use the ipmpstat –i command. If the output for a given interface includes an unknown status in its LINK column, then that interface does not support link-based failure detection. Refer to the manufacturer's documentation for more specific information about the network device.
Network drivers that support link-based failure detection monitor the interface's link state and notify the networking subsystem when that link state changes. When notified of a change, the networking subsystem either sets or clears the RUNNING flag for that interface, as appropriate. If the in.mpathd daemon detects that the interface's RUNNING flag has been cleared, the daemon immediately fails the interface.
IPMP supports failure detection in an anonymous group. By default, IPMP monitors the status only of interfaces that belong to IPMP groups. However, you can configure the IPMP daemon to also track the status of interfaces that do not belong to any IPMP group. Thus, these interfaces are considered to be part of an anonymous group. When you issue the ipmpstat –g command, the anonymous group is displayed as double-dashes (--). In anonymous groups, the interfaces have data addresses that also function as test addresses. Because these interfaces do not belong to a named IPMP group, these addresses are visible to applications. To enable the tracking of interfaces that are not part of an IPMP group, see How to Configure the Behavior of the IPMP Daemon.