JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
Sun Network 10GbE Switch 72p

User’s Guide
Oracle Technology Network
Library
PDF
Print View
Feedback
search filter icon
search icon

Document Information

Using This Documentation

Product Notes

Related Documentation

CLI Command Modes

Feedback

Support and Accessibility

Understanding the Switch

Switch Overview

Front Panel Components

Rear Panel Components

Confirming Switch Specifications

Physical Specifications

Electrical Specifications

Environmental Specifications

Acoustic Noise Emissions

Installing the Switch

Preparing to Install the Switch

Verify Shipping Kit Contents

Antistatic Precautions

Install the Switch in the Rack

Connecting Management Cables

Management Cable Requirements

NET MGT Port

Connect the NET MGT Cable

SER MGT Port

Connect the SER MGT Cable

Powering On the Switch

Power Cord Specifications

Power On the Switch

Connecting Ethernet Cables

QSFP Cables

SFP+ Cables

Splitter Cables

Ethernet Cable Cautions

Connect Ethernet Cables

Finish the Switch Installation

Administering the Switch

Connecting to the Service Processor

Oracle ILOM Overview

Oracle ILOM Features Not Supported

Verify the DHCP-Assigned IP Address and Host Name

Configure Network Management From CLI (SER MGT)

Log Into Oracle ILOM Web (NET MGT)

Log Into Oracle ILOM CLI (NET MGT)

Log Into Oracle ILOM CLI (SER MGT)

SER MGT Port Configuration Parameters

Configure Network Management From Web

Configure Network Management From CLI (NET MGT)

Log Out of ILOM

Configuring SEFOS User Privileges

Create a SEFOS User

Change a SEFOS User Privilege Level

Update the Firmware

Connecting to SEFOS

SEFOS Overview

Connect to SEFOS

Disconnect From SEFOS

Servicing the Switch

Troubleshooting the Switch

Identifying LEDs

Sensors Overview

Check Switch Status (LEDs)

Check Switch Status (Oracle ILOM)

Component Sensor Targets

Motherboard Sensor Targets

Understanding Service Procedures

Tools Needed for Service

Replaceable Components

Servicing Power Supplies

Power Off a Power Supply

Remove a Power Supply

Install a Power Supply

Power On a Power Supply

Servicing Fans

Remove a Fan

Install a Fan

Servicing Ethernet Cables

Remove an Ethernet Cable

Install an Ethernet Cable

Servicing the Battery

Remove the Battery

Install the Battery

Glossary

Index

Using This Documentation

This guide describes how to install and configure the Sun Network 10GbE Switch 72p from Oracle.

These instructions are designed for enterprise system administrators with experience installing network hardware and software.

Product Notes

For late-breaking information and known issues about this product, refer to the product notes at:

http://www.oracle.com/pls/topic/lookup?ctx=SN-10GbE-72p

Related Documentation

Documentation
Links
All Oracle products
http://oracle.com/documentation
Sun Blade 6000 Ethernet Switched NEM 24p 10GbE
http://www.oracle.com/pls/topic/lookup?ctx=SB6K-24p-10GbE
Sun Network 10GbE Switch 72p
http://www.oracle.com/pls/topic/lookup?ctx=SN-10GbE-72p
Sun Blade 6000 modular system
http://www.oracle.com/pls/topic/lookup?ctx=sb6000
Oracle Integrated Lights Out Manager (Oracle ILOM) 3.0
http://www.oracle.com/pls/topic/lookup?ctx=ilom30

For detailed information about the commands and options described in this document, refer to the Sun Ethernet Fabric Operating System CLI Base Reference Manual.

CLI Command Modes

The following table lists the configuration modes used in this document with their access and exit methods.

Command Mode
Access Method
Prompt
Exit Method
User EXEC
Access SEFOS from Oracle ILOM with read-only rights (privilege level 1).
SEFOS>
Use the logout or exit command to return to the Oracle ILOM prompt.
Privileged EXEC
Access SEFOS from Oracle ILOM with full administrative rights (privilege level 15).
SEFOS#
Use the logout or exit command to return to the Oracle ILOM prompt.
Global Configuration
From User EXEC mode, use the enable command.
SEFOS(config)#
Use the end command to return to Privileged EXEC mode.
Interface Configuration
From Global Configuration mode, use the interface interface-type interface-id command.
SEFOS(config-if)#
Use the exit command to return to Global Configuration mode, or use the end command to return to Privileged EXEC mode.

Feedback

Provide feedback on this documentation at:

http://www.oracle.com/goto/docfeedback

Support and Accessibility

Description
Links
Access electronic support through My Oracle Support
http://support.oracle.com

For hearing impaired:

http://www.oracle.com/accessibility/support.html
Learn about Oracle’s commitment to accessibility
http://www.oracle.com/us/corporate/accessibility/index.html
Copyright © 2011, 2012 , Oracle and/or its affiliates. All rights reserved. Legal Notices
Previous Next