JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
Sun Storage J4500 Array Service Manual
search filter icon
search icon

Document Information

Preface

1.  Introduction to the Sun Storage J4500 Array

1.1 Features

1.2 Exterior Features, Controls, and Indicators

1.2.1 Front Panel

1.2.2 Back Panel

1.2.3 Sun Storage J4500 Array Internal Components

1.3 Accessory Kit

2.  Configuring and Powering On the Sun Storage J4500 Array

2.1 Configuration and Cabling

2.1.1 Terms and Definitions

2.1.2 Configuration Rules

2.1.3 Cabling the SAS Connectors

2.1.4 Example Configurations

2.2 Powering On and Off the Array

To Power On the Array

To Place the Array Into Standby Power Mode

To Power Off the Array

2.2.1 AC Power Failure Auto-Recovery

3.  Maintaining the Sun Storage J4500 Array

3.1 Options and Replaceable Components

3.2 Tools and Supplies Needed

3.3 Powering Off the Array and Removing It From the Rack

To Power Off the Array

To Remove the Array Enclosure From the Rack

3.4 Removing and Replacing the Hard Disk Drive Access Cover

To Remove the Hard Disk Drive Access Cover

To Replace the Hard Disk Drive Access Cover

3.5 Internal Component Locations

3.6 Replacing Components

To Replace a Fan Module

To Replace the Front Indicator Board

To Replace a Hard Disk Drive

To Replace the Power Distribution Board

To Replace a Power Supply

To Replace the System Controller Module

To Replace the Array Chassis

3.7 Upgrading Enclosure Firmware

3.7.1 Ensure Both SAS Fabrics are Upgraded to the Same Firmware Revision Level

4.  Troubleshooting

4.1 External Status LEDs

4.2 Internal Disk Drive and Fan LEDs

4.3 Diagnostic and Management Tools

4.3.1 SunVTS

4.3.2 Common Array Manager (CAM)

4.4 Troubleshooting Problems with the Array

4.4.1 Initial Start-up

4.4.2 Check the Event and Performance Logs

4.4.3 Using the Array Management Software to Monitor Enclosure Health

4.4.4 Array Link Problems

4.4.5 Disk Problems

4.4.6 Array Environment Problems

4.4.7 Power Problems

4.5 Resetting the Enclosure Hardware

To Reset the Enclosure Hardware Using the Reset Button

4.6 Clearing the Enclosure Zoning Password

To Clear the Enclosure Zoning Password

A.  System Specifications

B.  Connector Pinouts

B.1 Mini-SAS Connectors

B.2 I/O-to-Disk Backplane Connectors

B.2.1 Power Blade Connector

B.2.2 High-Speed Dock Connectors

B.3 Power Supply Connector

B.4 Disk Backplane-to-Front Indicator Connector

B.5 Backplane-to-Disk-Backplane Connector

B.6 Fan Tray Connectors

B.7 Fan Connectors

Index

B.3 Power Supply Connector

The power supply connector has signal pins and power blades. See Power Supply Signal Connectors for signal pins and Power Supply Connector Power Blades for power blades.

Table B-5 Power Supply Signal Connectors

X,Y
1
2
3
4
5
6
7
D
3.3AUX
GND
12LS
Spare
SCL
A0
3.3 Vsb RS+
C
3.3AUX
GND
AC OK
+12V RS+
+12V RS-
A1
3.3 Vsb RS-
B
3.3AUX
GND
PSON
PSKILL
SDA
A2
Fan fail
A
3.3AUX
GND
PRESENT
PWOK
FAIL
ACL
Reserved

Table B-6 Power Supply Connector Power Blades

Pin
Function
P1
12VDC
P2
12VDC Return
P3
12VDC
P4
12VDC Return
P5
12VDC
P6
12VDC Return
P7
12VDC
P8
12VDC Return