rawshark
(1)
名称
rawshark - Dump and analyze raw pcap data
用法概要
rawshark [ -d <encap:dlt>|<proto:protoname> ]
[ -F <field to display> ] [ -h ] [ -l ] [ -n ]
[ -N <name resolving flags> ]
[ -o <preference setting> ] ... [ -p ] [ -r <pipe>|- ]
[ -R <read (display) filter> ] [ -s ] [ -S <field format> ]
[ -t ad|a|r|d|e ] [ -v ]
描述
The Wireshark Network Analyzer RAWSHARK(1)
NAME
rawshark - Dump and analyze raw pcap data
SYNOPSIS
rawshark [ -d <encap:dlt>|<proto:protoname> ]
[ -F <field to display> ] [ -h ] [ -l ] [ -n ]
[ -N <name resolving flags> ]
[ -o <preference setting> ] ... [ -p ] [ -r <pipe>|- ]
[ -R <read (display) filter> ] [ -s ] [ -S <field format> ]
[ -t ad|a|r|d|e ] [ -v ]
DESCRIPTION
Rawshark reads a stream of packets from a file or pipe, and
prints a line describing its output, followed by a set of
matching fields for each packet on stdout.
INPUT
Unlike TShark, Rawshark makes no assumptions about
encapsulation or input. The -d and -r flags must be
specified in order for it to run. One or more -F flags
should be specified in order for the output to be useful.
The other flags listed above follow the same conventions as
Wireshark and TShark.
Rawshark expects input records with the following format by
default. This matches the format of the packet header and
packet data in a pcap-formatted file on disk.
struct rawshark_rec_s {
uint32_t ts_sec; /* Time stamp (seconds) */
uint32_t ts_usec; /* Time stamp (microseconds) */
uint32_t caplen; /* Length of the packet buffer */
uint32_t len; /* "On the wire" length of the packet */
uint8_t data[caplen]; /* Packet data */
};
If -p is supplied rawshark expects the following format.
This matches the struct pcap_pkthdr structure and packet
data used in libpcap/WinPcap. This structure's format is
platform-dependent; the size of the tv_sec field in the
struct timeval structure could be 32 bits or 64 bits. For
rawshark to work, the layout of the structure in the input
must match the layout of the structure in rawshark. Note
that this format will probably be the same as the previous
format if rawshark is a 32-bit program, but will not
necessarily be the same if rawshark is a 64-bit program.
1.10.7 Last change: 2014-06-17 1
The Wireshark Network Analyzer RAWSHARK(1)
struct rawshark_rec_s {
struct timeval ts; /* Time stamp */
uint32_t caplen; /* Length of the packet buffer */
uint32_t len; /* "On the wire" length of the packet */
uint8_t data[caplen]; /* Packet data */
};
In either case, the endianness (byte ordering) of each
integer must match the system on which rawshark is running.
OUTPUT
If one or more fields are specified via the -F flag,
Rawshark prints the number, field type, and display format
for each field on the first line as "packet number" 0. For
each record, the packet number, matching fields, and a "1"
or "0" are printed to indicate if the field matched any
supplied display filter. A "-" is used to signal the end of
a field description and at the end of each packet line. For
example, the flags -F ip.src -F dns.qry.type might generate
the following output:
0 FT_IPv4 BASE_NONE - 1 FT_UINT16 BASE_HEX -
1 1="1" 0="192.168.77.10" 1 -
2 1="1" 0="192.168.77.250" 1 -
3 0="192.168.77.10" 1 -
4 0="74.125.19.104" 1 -
Note that packets 1 and 2 are DNS queries, and 3 and 4 are
not. Adding -R "not dns" still prints each line, but there's
an indication that packets 1 and 2 didn't pass the filter:
0 FT_IPv4 BASE_NONE - 1 FT_UINT16 BASE_HEX -
1 1="1" 0="192.168.77.10" 0 -
2 1="1" 0="192.168.77.250" 0 -
3 0="192.168.77.10" 1 -
4 0="74.125.19.104" 1 -
Also note that the output may be in any order, and that
multiple matching fields might be displayed.
OPTIONS
-d <encapsulation>
Specify how the packet data should be dissected. The
encapsulation is of the form type:value, where type is
one of:
encap:name Packet data should be dissected using the
libpcap/WinPcap data link type (DLT) name, e.g.
encap:EN10MB for Ethernet. Names are converted using
pcap_datalink_name_to_val(). A complete list of DLTs
can be found at <http://www.tcpdump.org/linktypes.html>.
1.10.7 Last change: 2014-06-17 2
The Wireshark Network Analyzer RAWSHARK(1)
encap:number Packet data should be dissected using the
libpcap/WinPcap DLT number, e.g. encap:105 for raw IEEE
802.11.
proto:protocol Packet data should be passed to the
specified Wireshark protocol dissector, e.g. proto:http
for HTTP data.
-F <field to display>
Add the matching field to the output. Fields are any
valid display filter field. More than one -F flag may be
specified, and each field can match multiple times in a
given packet. A single field may be specified per -F
flag. If you want to apply a display filter, use the -R
flag.
-h Print the version and options and exits.
-l Flush the standard output after the information for each
packet is printed. (This is not, strictly speaking,
line-buffered if -V was specified; however, it is the
same as line-buffered if -V wasn't specified, as only
one line is printed for each packet, and, as -l is
normally used when piping a live capture to a program or
script, so that output for a packet shows up as soon as
the packet is seen and dissected, it should work just as
well as true line-buffering. We do this as a workaround
for a deficiency in the Microsoft Visual C++ C library.)
This may be useful when piping the output of TShark to
another program, as it means that the program to which
the output is piped will see the dissected data for a
packet as soon as TShark sees the packet and generates
that output, rather than seeing it only when the
standard output buffer containing that data fills up.
-n Disable network object name resolution (such as
hostname, TCP and UDP port names), the -N flag might
override this one.
-N <name resolving flags>
Turn on name resolving only for particular types of
addresses and port numbers, with name resolving for
other types of addresses and port numbers turned off.
This flag overrides -n if both -N and -n are present. If
both -N and -n flags are not present, all name
resolutions are turned on.
The argument is a string that may contain the letters:
m to enable MAC address resolution
1.10.7 Last change: 2014-06-17 3
The Wireshark Network Analyzer RAWSHARK(1)
n to enable network address resolution
N to enable using external resolvers (e.g., DNS) for
network address resolution
t to enable transport-layer port number resolution
C to enable concurrent (asynchronous) DNS lookups
-o <preference>:<value>
Set a preference value, overriding the default value and
any value read from a preference file. The argument to
the option is a string of the form prefname:value, where
prefname is the name of the preference (which is the
same name that would appear in the preference file), and
value is the value to which it should be set.
-p Assume that packet data is preceded by a pcap_pkthdr
struct as defined in pcap.h. On some systems the size of
the timestamp data will be different from the data
written to disk. On other systems they are identical and
this flag has no effect.
-r <pipe>|-
Read packet data from input source. It can be either the
name of a FIFO (named pipe) or ``-'' to read data from
the standard input, and must have the record format
specified above.
-R <read (display) filter>
Cause the specified filter (which uses the syntax of
read/display filters, rather than that of capture
filters) to be applied before printing the output.
-s Allows standard pcap files to be used as input, by
skipping over the 24 byte pcap file header.
-S Use the specified format string to print each field. The
following formats are supported:
%D Field name or description, e.g. "Type" for
dns.qry.type
%N Base 10 numeric value of the field.
%S String value of the field.
For something similar to Wireshark's standard display
("Type: A (1)") you could use %D: %S (%N).
-t ad|a|r|d|e
Set the format of the packet timestamp printed in
1.10.7 Last change: 2014-06-17 4
The Wireshark Network Analyzer RAWSHARK(1)
summary lines, the default is relative. The format can
be one of:
ad absolute with date: The absolute date and time is the
actual time and date the packet was captured
a absolute: The absolute time is the actual time the
packet was captured, with no date displayed
r relative: The relative time is the time elapsed
between the first packet and the current packet
d delta: The delta time is the time since the previous
packet was captured
e epoch: The time in seconds since epoch (Jan 1, 1970
00:00:00)
-v Print the version and exit.
READ FILTER SYNTAX
For a complete table of protocol and protocol fields that
are filterable in TShark see the wireshark-filter(4) manual
page.
FILES
These files contains various Wireshark configuration values.
Preferences
The preferences files contain global (system-wide) and
personal preference settings. If the system-wide
preference file exists, it is read first, overriding the
default settings. If the personal preferences file
exists, it is read next, overriding any previous values.
Note: If the command line option -o is used (possibly
more than once), it will in turn override values from
the preferences files.
The preferences settings are in the form prefname:value,
one per line, where prefname is the name of the
preference and value is the value to which it should be
set; white space is allowed between : and value. A
preference setting can be continued on subsequent lines
by indenting the continuation lines with white space. A
# character starts a comment that runs to the end of the
line:
# Capture in promiscuous mode?
# TRUE or FALSE (case-insensitive).
capture.prom_mode: TRUE
The global preferences file is looked for in the
1.10.7 Last change: 2014-06-17 5
The Wireshark Network Analyzer RAWSHARK(1)
wireshark directory under the share subdirectory of the
main installation directory (for example,
/usr/local/share/wireshark/preferences) on UNIX-
compatible systems, and in the main installation
directory (for example, C:\Program
Files\Wireshark\preferences) on Windows systems.
The personal preferences file is looked for in
$HOME/.wireshark/preferences on UNIX-compatible systems
and %APPDATA%\Wireshark\preferences (or, if %APPDATA%
isn't defined, %USERPROFILE%\Application
Data\Wireshark\preferences) on Windows systems.
Disabled (Enabled) Protocols
The disabled_protos files contain system-wide and
personal lists of protocols that have been disabled, so
that their dissectors are never called. The files
contain protocol names, one per line, where the protocol
name is the same name that would be used in a display
filter for the protocol:
http
tcp # a comment
The global disabled_protos file uses the same directory
as the global preferences file.
The personal disabled_protos file uses the same
directory as the personal preferences file.
Name Resolution (hosts)
If the personal hosts file exists, it is used to resolve
IPv4 and IPv6 addresses before any other attempts are
made to resolve them. The file has the standard hosts
file syntax; each line contains one IP address and name,
separated by whitespace. The same directory as for the
personal preferences file is used.
Capture filter name resolution is handled by libpcap on
UNIX-compatible systems and WinPcap on Windows. As such
the Wireshark personal hosts file will not be consulted
for capture filter name resolution.
Name Resolution (ethers)
The ethers files are consulted to correlate 6-byte
hardware addresses to names. First the personal ethers
file is tried and if an address is not found there the
global ethers file is tried next.
Each line contains one hardware address and name,
separated by whitespace. The digits of the hardware
address are separated by colons (:), dashes (-) or
1.10.7 Last change: 2014-06-17 6
The Wireshark Network Analyzer RAWSHARK(1)
periods (.). The same separator character must be used
consistently in an address. The following three lines
are valid lines of an ethers file:
ff:ff:ff:ff:ff:ff Broadcast
c0-00-ff-ff-ff-ff TR_broadcast
00.00.00.00.00.00 Zero_broadcast
The global ethers file is looked for in the /etc
directory on UNIX-compatible systems, and in the main
installation directory (for example, C:\Program
Files\Wireshark) on Windows systems.
The personal ethers file is looked for in the same
directory as the personal preferences file.
Capture filter name resolution is handled by libpcap on
UNIX-compatible systems and WinPcap on Windows. As such
the Wireshark personal ethers file will not be consulted
for capture filter name resolution.
Name Resolution (manuf)
The manuf file is used to match the 3-byte vendor
portion of a 6-byte hardware address with the
manufacturer's name; it can also contain well-known MAC
addresses and address ranges specified with a netmask.
The format of the file is the same as the ethers files,
except that entries of the form:
00:00:0C Cisco
can be provided, with the 3-byte OUI and the name for a
vendor, and entries such as:
00-00-0C-07-AC/40 All-HSRP-routers
can be specified, with a MAC address and a mask
indicating how many bits of the address must match. The
above entry, for example, has 40 significant bits, or 5
bytes, and would match addresses from 00-00-0C-07-AC-00
through 00-00-0C-07-AC-FF. The mask need not be a
multiple of 8.
The manuf file is looked for in the same directory as
the global preferences file.
Name Resolution (ipxnets)
The ipxnets files are used to correlate 4-byte IPX
network numbers to names. First the global ipxnets file
is tried and if that address is not found there the
personal one is tried next.
1.10.7 Last change: 2014-06-17 7
The Wireshark Network Analyzer RAWSHARK(1)
The format is the same as the ethers file, except that
each address is four bytes instead of six.
Additionally, the address can be represented as a single
hexadecimal number, as is more common in the IPX world,
rather than four hex octets. For example, these four
lines are valid lines of an ipxnets file:
C0.A8.2C.00 HR
c0-a8-1c-00 CEO
00:00:BE:EF IT_Server1
110f FileServer3
The global ipxnets file is looked for in the /etc
directory on UNIX-compatible systems, and in the main
installation directory (for example, C:\Program
Files\Wireshark) on Windows systems.
The personal ipxnets file is looked for in the same
directory as the personal preferences file.
ENVIRONMENT VARIABLES
WIRESHARK_DEBUG_EP_NO_CHUNKS
Normally per-packet memory is allocated in large
"chunks." This behavior doesn't work well with
debugging tools such as Valgrind or ElectricFence.
Export this environment variable to force individual
allocations. Note: disabling chunks also disables
canaries (see below).
WIRESHARK_DEBUG_SE_NO_CHUNKS
Normally per-file memory is allocated in large "chunks."
This behavior doesn't work well with debugging tools
such as Valgrind or ElectricFence. Export this
environment variable to force individual allocations.
Note: disabling chunks also disables canaries (see
below).
WIRESHARK_DEBUG_EP_NO_CANARY
Normally per-packet memory allocations are separated by
"canaries" which allow detection of memory overruns.
This comes at the expense of some extra memory usage.
Exporting this environment variable disables these
canaries.
WIRESHARK_DEBUG_SE_USE_CANARY
Exporting this environment variable causes per-file
memory allocations to be protected with "canaries" which
allow for detection of memory overruns. This comes at
the expense of significant extra memory usage.
WIRESHARK_DEBUG_SCRUB_MEMORY
If this environment variable is set, the contents of
1.10.7 Last change: 2014-06-17 8
The Wireshark Network Analyzer RAWSHARK(1)
per-packet and per-file memory is initialized to
0xBADDCAFE when the memory is allocated and is reset to
0xDEADBEEF when the memory is freed. This functionality
is useful mainly to developers looking for bugs in the
way memory is handled.
WIRESHARK_DEBUG_WMEM_OVERRIDE
Setting this environment variable forces the wmem
framework to use the specified allocator backend for
*all* allocations, regardless of which backend is
normally specified by the code. This is mainly useful to
developers when testing or debugging. See README.wmem in
the source distribution for details.
WIRESHARK_RUN_FROM_BUILD_DIRECTORY
This environment variable causes the plugins and other
data files to be loaded from the build directory (where
the program was compiled) rather than from the standard
locations. It has no effect when the program in
question is running with root (or setuid) permissions on
*NIX.
WIRESHARK_DATA_DIR
This environment variable causes the various data files
to be loaded from a directory other than the standard
locations. It has no effect when the program in
question is running with root (or setuid) permissions on
*NIX.
WIRESHARK_PYTHON_DIR
This environment variable points to an alternate
location for Python. It has no effect when the program
in question is running with root (or setuid) permissions
on *NIX.
ERF_RECORDS_TO_CHECK
This environment variable controls the number of ERF
records checked when deciding if a file really is in the
ERF format. Setting this environment variable a number
higher than the default (20) would make false positives
less likely.
IPFIX_RECORDS_TO_CHECK
This environment variable controls the number of IPFIX
records checked when deciding if a file really is in the
IPFIX format. Setting this environment variable a
number higher than the default (20) would make false
positives less likely.
WIRESHARK_ABORT_ON_DISSECTOR_BUG
If this environment variable is set, Rawshark will call
abort(3) when a dissector bug is encountered. abort(3)
1.10.7 Last change: 2014-06-17 9
The Wireshark Network Analyzer RAWSHARK(1)
will cause the program to exit abnormally; if you are
running Rawshark in a debugger, it should halt in the
debugger and allow inspection of the process, and, if
you are not running it in a debugger, it will, on some
OSes, assuming your environment is configured correctly,
generate a core dump file. This can be useful to
developers attempting to troubleshoot a problem with a
protocol dissector.
WIRESHARK_EP_VERIFY_POINTERS
This environment variable, if set, causes certain uses
of pointers to be audited to ensure they do not point to
memory that is deallocated after each packet has been
fully dissected. This can be useful to developers
writing or auditing code.
WIRESHARK_SE_VERIFY_POINTERS
This environment variable, if set, causes certain uses
of pointers to be audited to ensure they do not point to
memory that is deallocated after when a capture file is
closed. This can be useful to developers writing or
auditing code.
WIRESHARK_ABORT_ON_OUT_OF_MEMORY
This environment variable, if present, causes abort(3)
to be called if certain out-of-memory conditions (which
normally result in an exception and an explanatory error
message) are experienced. This can be useful to
developers debugging out-of-memory conditions.
ATTRIBUTES
See attributes(5) for descriptions of the following
attributes:
+---------------+---------------------------------------+
|ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+---------------+---------------------------------------+
|Availability | diagnostic/wireshark/wireshark-common |
+---------------+---------------------------------------+
|Stability | Uncommitted |
+---------------+---------------------------------------+
SEE ALSO
wireshark-filter(4), wireshark(1), tshark(1), editcap(1),
pcap(3), dumpcap(1), text2pcap(1), pcap-filter(5) or
tcpdump(1)
NOTES
Rawshark is part of the Wireshark distribution. The latest
version of Wireshark can be found at
<http://www.wireshark.org>.
1.10.7 Last change: 2014-06-17 10
The Wireshark Network Analyzer RAWSHARK(1)
HTML versions of the Wireshark project man pages are
available at: http://www.wireshark.org/docs/man-pages
<http://www.wireshark.org/docs/man-pages>.
AUTHORS
Rawshark uses the same packet dissection code that Wireshark
does, as well as using many other modules from Wireshark;
see the list of authors in the Wireshark man page for a list
of authors of that code.
This software was built from source available at
https://java.net/projects/solaris-userland. The original
community source was downloaded from
http://www.wireshark.org/download/src/all-
versions/wireshark-1.10.7.tar.bz2
Further information about this software can be found on the
open source community website at http://www.wireshark.org/.
1.10.7 Last change: 2014-06-17 11