|
Oracle Server
|
Access the service processor (SP) to 1) monitor the system health;
2) view server component inventory; and 3) configure and view Oracle
ILOM administration properties.
From the server SP CLI, you can access the following
namespaces:
-
/SP – Use the
/SP target to configure Oracle ILOM
administration properties and to view log files.
-
/HOST – Use the
/HOST target to monitor and manage
HOST related properties.
-
/Servers – Use the
/Servers target to view and manage
existing PDomain configurations on multi-host SPARC servers
(/Servers/PDomains/PDomain_n).
-
/System – Use the
/System target to monitor component
inventory and environmental sensors.
|
x86 servers
SPARC T and M series servers
Oracle ILOM 3.1 and later
|
|
Oracle Blade Chassis System
|
Access the chassis monitoring module (CMM) to 1) monitor system
health; 2) view chassis component inventory; 3) navigate to chassis
components (blade server modules, power supplies, storage, and so
on), and 5) configure and view Oracle ILOM administration
properties.
From the CMM CLI, you can access the following namespaces:
-
/CMM – Use the
/CMM target to 1) access the server
SPs, 2) configure the Oracle ILOM SP administration
properties, and 3) view the audit and event log files.
-
/Storage (3.0 legacy target,
visible when enabled) – Use the
/Storage target to 1) access and
configure the SAS zoning interface, and 2) manage the
chassis storage components or storage blade server modules.
-
/Servers – Use the
/Servers target to monitor and manage
blade server modules as if you were logged into the blade
server at the SP level.
-
/Systems – Use the
/Systems target to view a top-level
summary of system inventory, component health status, and
the system log.
-
/CH (3.0 legacy target,
visible only when enabled) – Use the
/CH target to monitor component
inventory, environmental health status, and hardware
management at the chassis level. The targets under this
target directly correspond to the names of the hardware
components.
Note -
The 3.0 legacy targets under the CMM are available (whether
you see them or not) to ensure backward compatibility with
existing Oracle ILOM user scripts.
|
Oracle Blade 6000 Chassis
CMM
x86 and SPARC blade server modules
Oracle ILOM 3.1 and later
|
|
Oracle Netra Frame Modular System
|
Access the Frame Monitoring Module (FMM) to: 1) monitor system
health; 2) view component inventory; 3) navigate to computer
node(s), and 5) configure and view Oracle ILOM administration
properties.
From the FMM CLI, you can access the following namespaces:
-
/FMM – Use the
/FMM target to configure Oracle ILOM
users and administration properties, as well as to view
audit and event FMM log files.
-
/Networking – Use the
/Networking target to manage the
Network node(s) as if you were logged into the Network
node(s) at the SP level.
Note -
The /Networking target might not
be supported on all FMMs running Oracle ILOM firmware
version 3.2.5. A later firmware version might be
required.
-
/Servers – Use the
/Servers target to manage the compute
node(s) as if you were logged in to the compute node(s) at
the SP level.
-
/Systems – Use the
/Systems target for a top-level
summary view of open problems, compute and networking
inventory and health details, and events in the system log.
-
/FRAME (legacy target) – Use the
/FRAME target to view inventory
status, environments (alarms, LEDs, sensors and so on), and
to manage hardware components at the Frame level.
|
Netra Frame Chassis
x5-2 server compute nodes
FMM
Oracle ILOM firmware 3.2.5 and later.
|