See:
See Log In to the SP (SER MGT) or Log In to the SP (Network Management).
-> start /System/Networking/Switches/Switch_0/fs_cli
Are you sure you want to start /System/Networking/Switches/Switch_0/fs_cli
(y/n)? y
Management Switch for Oracle Fabric Interconnect F2-12
SEFOS login:
SEFOS login: root Password: admin123 SEFOS#
The default password is admin123.
SEFOS# show interfaces status Port Status Duplex Speed Negotiation Capability --- ------ ------ ----- ----------- ---------- Gi0/1 connected Full 1 Gbps Auto Auto-MDIX on Gi0/2 not connected Half - Auto Auto-MDIX on Gi0/3 not connected Half - Auto Auto-MDIX on Gi0/4 not connected Half - Auto Auto-MDIX on Gi0/5 connected Full 1 Gbps Auto Auto-MDIX on Gi0/6 connected Full 1 Gbps Auto Auto-MDIX on Gi0/7 not connected Half - Auto Auto-MDIX on Gi0/8 connected Full 1 Gbps Auto Auto-MDIX on Gi0/9 connected Full 1 Gbps Auto Auto-MDIX on Gi0/10 not connected Half - Auto Auto-MDIX on Gi0/11 connected Full 1 Gbps Auto Auto-MDIX on Gi0/12 connected Full 1 Gbps Auto Auto-MDIX on Gi0/13 not connected Half - Auto Auto-MDIX on Gi0/14 connected Full 1 Gbps Auto Auto-MDIX on Gi0/15 connected Full 1 Gbps Auto Auto-MDIX on Gi0/16 not connected Half - Auto Auto-MDIX on Gi0/17 connected Full 1 Gbps Auto Auto-MDIX on Gi0/18 connected Full 1 Gbps Auto Auto-MDIX on SEFOS#
In the output:
Port – Port of the EMS module as connected to chassis components.
Gi0/1 to Gi0/4 – Four 1GBASE-T ports on the left rear of the switch.
Gi0/5 to Gi0/11 – One port per slot on the rear panel. Gi0/5 is connected to slot 0, and Gi0/16 is connected to slot 11.
Gi0/17 and Gi0/18 are internal to the switch architecture.
Status – State of the port.
Duplex, Speed, and Negotiation – Parameters of the link.
Capability – Indicates if auto-crossover capability is on.
Refer to detecting and managing faults in the Oracle Fabric Interconnect F2-12 Service Manual and to the EMS module documentation.
SEFOS# exit Connection closed by foreign host Entering character mode Escape character is '^]'. start: The session with /System/Networking/Switches/Switch_0/fs_cli has ended. ->
-> start /HOST/console Are you sure you want to start /HOST/console (y/n)? y Serial console started. To stop, type ESC (
hostname login: Password:
where hostname is the host name of the SCP.
hostname login: admin
Password: password
Welcome to OFOS Controller
Copyright (c) 2012, 2016, Oracle and/or its affiliates. All rights reserved.
Enter "help" for information on available commands.
Enter the command "show system copyright" for licensing information
admin@hostname[OFOS]
[OFOS] show iocards slot state descr type v-resources -------------------------------------------------------------------------------- 0 up/up gwEthernet4Port40GbCard 0 1 up/up gwEthernet4Port40GbCard 0 3 up/up sanFc2Port16GbCard 0 4 up/up sanFc2Port16GbCard 0 6 up/up ibLr4Port100GbCard 7 up/up ibLr4Port100GbCard 9 up/up gwEthernet4Port10GbCard 0 10 up/up gwEthernet4Port10GbCard 0 embedded up/up spineIb4Gw2PortCard 0 9 records displayed [OFOS]
In the output:
slot – Slot number as seen on the rear panel.
state– Operational and administrative state of the I/O module in the listed slot.
descr – An optional description of the module or slot.
type – Type of module installed in the slot.
gwEthernet4Port40GbCard – Oracle F2 10 Gb and 40 Gb Ethernet module
sanFc2Port16GbCard – Oracle F2 Dual Port 16Gb Fibre Channel module
ibLr4Port100GbCard – Oracle F2 Long Range InfiniBand module
gwEthernet4Port10GbCard – Oracle F2 Quad Port 10GBASE-T module
spineIb4Gw2PortCard – The interfaces at the left rear of the switch.
v-resources – Indicates a value for internal switch use. This value is not useful to customers.
Refer to detecting and managing faults in the Oracle Fabric Interconnect F2-12 Service Manual.
[OFOS] show ioports name type state descr v-resources ------------------------------------------------------------------------------ 0/1 gwEthernet40GbPort up/up 0 0/2 gwEthernet40GbPort up/up 0 0/3 gwEthernet40GbPort up/up 0 0/4 gwEthernet40GbPort up/up 0 1/1 gwEthernet40GbPort up/up 0 1/2 gwEthernet40GbPort up/up 0 1/3 gwEthernet40GbPort up/up 0 1/4 gwEthernet40GbPort up/up 0 3/1 sanFc16GbPort up/up 0 3/2 sanFc16GbPort up/up 0 4/1 sanFc16GbPort up/up 0 4/2 sanFc16GbPort up/up 0 9/1 gwEthernet10GbPort up/up 0 9/2 gwEthernet10GbPort up/up 0 9/3 gwEthernet10GbPort up/up 0 9/4 gwEthernet10GbPort up/up 0 10/1 gwEthernet10GbPort up/up 0 10/2 gwEthernet10GbPort up/up 0 10/3 gwEthernet10GbPort up/up 0 10/4 gwEthernet10GbPort up/up 0 embedded/5 gwEthernet40GbPort up/up 0 embedded/6 gwEthernet40GbPort up/up 0 22 records displayed [OFOS]
In the output:
name – Slot number and port as seen on the rear panel/port number for the interface.
type – Type of gateway available in the slot.
gwEthernet40GbPort – 40 Gb Ethernet
gwEthernet10GbPort – 10 Gb Ethernet
sanFc16GbPort – 16 Gb Fibre Channel
state– Operational and administrative state of the I/O module in the listed slot.
descr – An optional description of the module or slot.
v-resources – Indicates a value for internal switch use. This value is not useful to customers.
[OFOS] show infiniband-port name state mode_state guid -------------------------------------------------------------- 6/1 up/down switching 0 6/2 up/down switching 0 6/3 up/down switching 0 6/4 up/down switching 0 7/1 up/down switching 0 7/2 up/down switching 0 7/3 up/down switching 0 7/4 up/down switching 0 embedded/1 up/down switching 0 embedded/2 up/down switching 0 embedded/3 up/down switching 0 embedded/4 up/down switching 0 12 records displayed [OFOS]
In the output:
name – Slot number as seen on the rear panel or port number for the interface.
state– Operational and administrative state of the listed port.
mode_state – State of the IB port as configured for switching or routing.
guid – Node GUID of each switch port.
Refer to the detecting and managing faults in the Oracle Fabric Interconnect F2-12 Service Manual, and to the Oracle Fabric OS documentation for assistance.
Type exit and press the Enter key, then press the Esc key and type (.
[OFOS] exit [root@azn111-222 ~]# Serial console stopped. ->