df [-F FSType] [-abeghklntPVvZ] [-o FSType-specific_options] [block_device | directory | file | resource ...]
The df utility displays the amount of disk space occupied by mounted or unmounted file systems, the amount of used and available space, and how much of the file system's total capacity has been used. The file system is specified by device, or by referring to a file or directory on the specified file system.
Used without operands or options, df reports on all mounted file systems.
df may not be supported for all FSTypes.
If df is run on a networked mount point that the automounter has not yet mounted, the file system size will be reported as zero. As soon as the automounter mounts the file system, the sizes will be reported correctly.
The following options are supported:
Reports on all file systems including ones whose entries in /etc/mnttab (see mnttab(4)) have the ignore option set.
Prints the total number of kilobytes free.
Prints only the number of files free.
Specifies the FSType on which to operate. The –F option is intended for use with unmounted file systems. The FSType should be specified here or be determinable from /etc/vfstab (see vfstab(4)) by matching the directory, block_device, or resource with an entry in the table, or by consulting /etc/default/fs. See default_fs(4).
Prints the entire statvfs(2) structure. This option is used only for mounted file systems. It can not be used with the –o option. This option overrides the –b, –e, –k, –n, –P, and –t options.
Like –k, except that sizes are in a more human readable format. The output consists of one line of information for each specified file system. This information includes the file system name, the total space allocated in the file system, the amount of space allocated to existing files, the total amount of space available for the creation of new files by unprivileged users, and the percentage of normally available space that is currently allocated to all files on the file system. All sizes are scaled to a human readable format, for example, 14K, 234M, 2.7G, or 3.0T. Scaling is done by repetitively dividing by 1024.
This option overrides the –b, –e, –g, –k, –n, –t, and –V options. This option only works on mounted filesystems and can not be used together with –o option.
Prints the allocation in kbytes. The output consists of one line of information for each specified file system. This information includes the file system name, the total space allocated in the file system, the amount of space allocated to existing files, the total amount of space available for the creation of new files by unprivileged users, and the percentage of normally available space that is currently allocated to all files on the file system. This option overrides the –b, –e, –n, and –t options and may not be used together with the –v option.
Reports on local file systems only. This option is used only for mounted file systems. It can not be used with the –o option.
Prints only the FSType name. Invoked with no operands, this option prints a list of mounted file system types. This option is used only for mounted file systems. It can not be used with the –o option.
Specifies FSType-specific options. These options are comma-separated, with no intervening spaces. See the manual page for the FSType-specific command for details.
Prints full listings with totals. This option overrides the –b, –e, and –n options.
Same as –h except in 512-byte units.
Echoes the complete set of file system specific command lines, but does not execute them. The command line is generated by using the options and operands provided by the user and adding to them information derived from /etc/mnttab, /etc/vfstab, or /etc/default/fs. This option may be used to verify and validate the command line.
Like –k, except that sizes are displayed in multiples of the smallest block size supported by each specified file system.
This option may not be used with the –k option.
The output consists of one line of information for each file system. This one line of information includes the following:
the file system's mount point
the file system's name
the total number of blocks allocated to the file system
the number of blocks allocated to existing files
the number of blocks available for the creation of new files by unprivileged users
the percentage of blocks in use by files
Displays mounts in all visible zones. By default, df displays mounts located only within the current zone. This option has no effect in a non-global zone.
The df utility interprets operands according to the following precedence: block_device, directory, file, resource. The following operands are supported:
Represents a block special device (for example, /dev/dsk/c1d0s7).
Represents a valid directory name. df reports on the file system that contains directory.
Represents a valid file name. df reports on the file system that contains file.
Represents an NFS resource name.
See largefile(5) for the description of the behavior of df when encountering files greater than or equal to 2 Gbyte ( 231 bytes).
The following example shows the df command and its output:
example% /usr/bin/df / (/dev/dsk/c0t0d0s0 ): 287530 blocks 92028 files /system/contract (ctfs ): 0 blocks 2147483572 files /system/object (objfs ): 0 blocks 2147483511 files /usr (/dev/dsk/c0t0d0s6 ): 1020214 blocks 268550 files /proc (/proc ): 0 blocks 878 files /dev/fd (fd ): 0 blocks 0 files /etc/mnttab (mnttab ): 0 blocks 0 files /var/run (swap ): 396016 blocks 9375 files /tmp (swap ): 396016 blocks 9375 files /opt (/dev/dsk/c0t0d0s5 ): 381552 blocks 96649 files /export/home (/dev/dsk/c0t0d0s7 ): 434364 blocks 108220 files
where the columns represent the mount point, device (or “filesystem”, according to df –k), free blocks, and free files, respectively. For contract file systems, /system/contract is the mount point, ctfs is the contract file system (used by SMF) with 0 free blocks and 2147483582(INTMAX-1) free files. For object file systems, /system/object is the mount point, objfs is the object file system (see objfs(7FS)) with 0 free blocks and 2147483511 free files.Example 2 Writing Portable Information About the /usr File System
The following example writes portable information about the /usr file system:
example% /usr/bin/df -P /usrExample 3 Writing Portable Information About the /usr/src file System
Assuming that /usr/src is part of the /usr file system, the following example writes portable information :
example% /usr/bin/df -P /usr/srcExample 4 Using df to Display Inode Usage
The following example displays inode usage on all ufs file systems:
example%/usr/bin/df -F ufs -o i
When set, any header which normally displays files will now display nodes. See environ(5) for descriptions of the following environment variables that affect the execution of df: LANG, LC_ALL, LC_CTYPE, LC_MESSAGES, and NLSPATH.
The following exit values are returned:
An error occurred.
Default local file system type. Default values can be set for the following flags in /etc/default/fs. For example: LOCAL=ufs, where LOCAL is the default partition for a command if no FSType is specified.
List of default parameters for each file system
See attributes(5) for descriptions of the following attributes:
If UFS logging is enabled on a file system, the disk space used for the log is reflected in the df report. The log is allocated from free blocks on the file system, and it is sized approximately 1 Mbyte per 1 Gbyte of file system, up to 256 Mbytes. The log size may be larger (up to a maximum of 512 Mbytes) depending on the number of cylinder groups present in the file system.