Skip Navigation Links | |
Exit Print View | |
Sun Network QDR InfiniBand Gateway Switch HTML Document Collection for Firmware Version 2.0 |
Network Management Connector and Pins
USB Management Connector and Pins
Preparing to Install the Gateway
Suggested Tools for Installation
Antistatic Precautions for Installation
Verify Shipping Carton Contents
Assemble the Ethernet Splitter Data Cables
Install the Gateway in the Rack
Verifying the InfiniBand Fabric
Understanding Routing Through the Gateway
Understanding Administrative Commands
Administering the I4 Switch Chip
Controlling the I4 Switch Chip
Administering the Subnet Manager
Controlling the Subnet Manager
Administering the InfiniBand Fabric
Monitoring the InfiniBand Fabric
Controlling the InfiniBand Fabric
Configuring the Fabric Director Node List
Partitioning the InfiniBand Fabric
Administering Gateway Resources
Installing Gateway Supportive Software (Linux)
Creating VNICs Under Gateway Manual Mode (Linux)
Creating VNICs Under Host Manual Mode (Linux)
Creating Virtual IO Adapters (Oracle Solaris)
Controlling Gateway Ports and Parameters
Understanding Oracle ILOM on the Gateway
Understanding Oracle ILOM Targets
Administering Oracle ILOM (CLI)
Accessing Oracle ILOM From the CLI
Switching Between the Oracle ILOM Shell and the Linux Shell
Monitoring Oracle ILOM Targets (CLI)
Controlling Oracle ILOM Targets (CLI)
Upgrading the Gateway Firmware Through Oracle ILOM (CLI)
Administering Oracle ILOM (Web)
Access Oracle ILOM From the Web Interface
Monitoring Oracle ILOM Targets (Web)
Controlling Oracle ILOM Targets (Web)
Upgrade the Gateway Firmware (Web)
Accessing the Rear Panel Diagram
Accessing Status Pane Information
Monitoring Parameters and Status
Administering Oracle ILOM (SNMP)
Monitoring Oracle ILOM Targets (SNMP)
Controlling Oracle ILOM Targets (SNMP)
Display the Sensor States (IPMI)
Display the Sensor Information (IPMI)
Display the System Event Log (IPMI)
Display FRU ID Information (IPMI)
Display Gateway Status LED States (IPMI)
Disable the Locator LED (IPMI)
Understanding Oracle ILOM Commands
Understanding Service Procedures
Antistatic Precautions for Service
Remove the Gateway From the Rack
Understanding Hardware Commands
Linux Shells for Hardware Commands
Understanding InfiniBand Commands
Linux Shells for InfiniBand Commands
Understanding the SUN-DCS-IB-MIB MIB OIDs
Understanding the SUN-FABRIC-MIB MIB OIDs
Understanding the SUN-HW-TRAP-MIB MIB OIDs
Understanding the SUN-ILOM-CONTROL-MIB MIB OIDs
Understanding the SUN-PLATFORM-MIB MIB OIDs
Displays port counters.
getportcounters port|connector [-R]
where:
port is the number of the port (1–36).
connector is the name of the connector (0A – 15A, 0A-ETH, 1A-ETH, 0B – 15B).
Note - The subordinate names of the 10 GbE connectors, 0A-ETH-1 to 0A-ETH-4 and 1A-ETH-1 to 1A-ETH-4 are also valid connector names.
This hardware command returns the error and data throughput counters of the specified port of the switch chip or connector of the gateway. If a port is specified, then the output is for InfiniBand counters. Similarly, if the connector specified is 0A to 15B, the output is also for InfiniBand counters. If the connector specified is 0A-ETH, 1A-ETH, or a subordinate connector, the output is for 10GbE counters.
The -R option clears the counters for the specified port or connector.
The getportcounters command is available from the /SYS/Switch_Diag, /SYS/Gateway_Mgmt, and /SYS/Fabric_Mgmt Linux shell targets of the Oracle ILOM CLI interface.
This example shows how to display the status of connector 1A-ETH-1 with the getportcounters command.
# getportcounters 1A-ETH-1 ETH Port 1A-ETH-1 ---------------------------------- RX bytes:........................0x6a5559 RX packets:......................0xd650 RX Jumbo packets:................0x0 RX unicast packets:..............0x0 RX multicast packets:............0xbcfc RX broadcast packets:............0x1954 RX no buffer:....................0x0 RX CRC:..........................0x0 RX runt:.........................0x0 RX errors:.......................0x0 TX bytes:........................0x0 TX packets:......................0x0 TX Jumbo packets:................0x0 TX unicast packets:..............0x0 TX multicast packets:............0x0 TX broadcast packets:............0x0 TX errors:.......................0x0 #