Oracle® Switch ES2-72 and Oracle Switch ES2-64 Configuration Guide

Exit Print View

 
Updated: April 2015
 
 

Configure Static Unicast Route Entries

This task configures the static route entries in SEFOS and verifies that traffic is reachable across networks.

Note - Before performing this task, erase any previous configurations on the switches.

See Routing Feature Topology for the topology of this task.

  1. Configure the initial settings.

    See Configure Initial Settings.

  2. If GVRP and GMRP are enabled, disable them so that the VLAN creation will not be propagated.
    SEFOS-1# configure terminal
SEFOS-1(config)# set gvrp disable
SEFOS-1(config)# set gmrp disable
SEFOS-1(config)# end
SEFOS-1# show vlan device info
 
Vlan device configurations
--------------------------
Vlan Status                       : Enabled
Vlan Oper status                  : Enabled
Gvrp status                       : Disabled
Gmrp status                       : Disabled
Gvrp Oper status                  : Disabled
Gmrp Oper status                  : Disabled

    The set gvrp disable and set gmrp disable commands disable these protocols. The show vlan device info command shows the VLAN configuration information.

  3. Configure SEFOS-1.

    See Routing Feature Topology.

    1. Remove the IP address of VLAN 1.
      SEFOS-1# configure terminal
SEFOS-1(config)# interface vlan 1
SEFOS-1(config-if)# no ip address
SEFOS-1(config-if)# exit
SEFOS-1(config)# vlan 10
SEFOS-1(config-vlan)# exit
SEFOS-1(config)# interface range xl-ethernet 0/25-26
SEFOS-1(config-if-range)# switchport access vlan 10
SEFOS-1(config-if-range)# no shutdown
SEFOS-1(config-if-range)# exit
SEFOS-1(config)# interface vlan 10
SEFOS-1(config-if)# shut
SEFOS-1(config-if)# ip address 10.0.0.201 255.255.255.0
SEFOS-1(config-if)# no shutdown
SEFOS-1(config-if)# end

      The default IP address of VLAN 1 is 10.0.0.1, and the IP address of VLAN 10 is 10.0.0.201. So you must remove the IP address of VLAN 1 before you can add the IP address for VLAN 10.

    2. Ping host A from SEFOS-1.
      SEFOS-1# ping 10.0.0.169
    3. Ping host A-2 from SEFOS-1.
      SEFOS-1# ping 10.0.0.152
    4. Ping SEFOS-1 and host A-2 from host A.
      # ping 10.0.201
10.0.201 is alive
# ping 10.0.0.152
10.0.0.152 is alive
#
  4. Configure the SEFOS-2 switch based on the topology.

    See Routing Feature Topology.

    SEFOS-2# configure terminal
SEFOS-2(config)# interface vlan 1
SEFOS-2(config-if)# no ip address
SEFOS-2(config-if)# exit
SEFOS-2(config)# vlan 40
SEFOS-2(config-vlan)# exit
SEFOS-2(config)# interface range xl-ethernet 0/25-26
SEFOS-2(config-if-range)# shutdown
SEFOS-2(config-if-range)# switchport access vlan 40
SEFOS-2(config-if-range)# no shutdown
SEFOS-2(config-if-range)# exit
SEFOS-2(config)# interface vlan 40
SEFOS-2(config-if)# shutdown
SEFOS-2(config-if)# ip address 40.0.0.200 255.255.255.0
SEFOS-2(config-if)# no shutdown
SEFOS-2(config-if)# end
SEFOS-2#
  5. Ping host B and host B-2 from SEFOS-2.
    SEFOS-2# ping 40.0.0.110
SEFOS-2# ping 40.0.0.118
  6. Create VLAN 20 between the two switches.

    Use ports 1 to 2 on both switches.

    1. Create VLAN 20 on SEFOS-1, ports 21 to 22.
      SEFOS-1# configure terminal
SEFOS-1(config)# interface range xl-ethernet 0/1-2
SEFOS-1(config-if-range)# switchport access vlan 20
SEFOS-1(config-if-range)# no shutdown
SEFOS-1(config-if-range)# exit
SEFOS-1(config)# interface vlan 20
SEFOS-1(config-if)# shutdown
SEFOS-1(config-if)# ip address 20.0.0.201 255.255.255.0
SEFOS-1(config-if)# no shutdown
SEFOS-1(config-if)# end
SEFOS-1#
    2. Create VLAN 20 on SEFOS-2, ports 21 to 22.
      SEFOS-2# configure terminal
SEFOS-2(config)# interface range xl-ethernet 0/1-2
SEFOS-2(config-if-range)# switchport access vlan 20
SEFOS-2(config-if-range)# no shutdown
SEFOS-2(config-if-range)# exit
SEFOS-2(config)# interface vlan 20
SEFOS-2(config-if)# shutdown
SEFOS-2(config-if)# ip address 20.0.0.200 255.255.255.0
SEFOS-2(config-if)# no shutdown
SEFOS-2(config-if)# end
SEFOS-2# ping 20.0.0.201

      You can now use this configuration as a starting point for different router configurations.

  7. Save the configuration.
    1. On on SEFOS-1, type: 
      SEFOS-1# write startup-config
Building configuration _
[OK]
    2. On SEFOS-2, type:
      SEFOS-2# write startup-config
Building configuration _
[OK]

    Switches start with the saved configuration on reboot.

  8. Verify that the existing routes are available in SEFOS-1.
    1. On SEFOS-1, type: 
      SEFOS-1# show ip route
Codes: C - connected, S - static, R - rip, B - bgp, O - ospf
 
C 10.0.0.0/24 is directly connected, vlan10
C 20.0.0.0/24 is directly connected, vlan20
SEFOS-1#
    2. On SEFOS-2, type: 
      SEFOS-2# show ip route
Codes: C - connected, S - static, R - rip, B - bgp, O - ospf
 
C 20.0.0.0/24 is directly connected, vlan20
C 40.0.0.0/24 is directly connected, vlan40
 
SEFOS-2#

      If there is no known route from SEFOS-1 to host B, the ping from host A to host B fails.

  9. Configure the static route in the SEFOS-1.
    SEFOS-1# configure terminal
SEFOS-1(config)# ip route 40.0.0.0 255.255.255.0 20.0.0.200
SEFOS-1(config)# end
  10. Configure the static route in SEFOS-2.
    SEFOS-2# configure terminal
SEFOS-2(config)# ip route 10.0.0.0 255.255.255.0 20.0.0.201
SEFOS-2(config)# end
  11. Verify that the routes are known to SEFOS-1 and SEFOS-2.
    1. On SEFOS-1, type: 
      SEFOS-1# show ip route
Codes: C - connected, S - static, R - rip, B - bgp, O - ospf
C 10.0.0.0/24 is directly connected, vlan10
C 20.0.0.0/24 is directly connected, vlan20
S 40.0.0.0/24 [-1] via 20.0.0.200
    2. On SEFOS-2, type: 
      SEFOS-2# show ip route
Codes: C - connected, S - static, R - rip, B - bgp, O - ospf
S 10.0.0.0/24 [-1] via 20.0.0.201
C 20.0.0.0/24 is directly connected, vlan20
C 40.0.0.0/24 is directly connected, vlan40

Related Information

Copyright © 2015, Oracle and/or its affiliates. All rights reserved. Legal Notices
Previous
Next