Index
Numbers and Symbols
A
- activate blade server,
Boot From Secondary BIOS
- ADM1026,
I2C Device Mapping
- administration, network,
Administering the Network
- AMC
- connectors,
On-Board Connectors
- description,
System Configurations
- drives, support,
Networking and I/O
- installation,
Install an Advanced Mezzanine Card
- remove,
Remove an AMC
- support,
Advanced Mezzanine Card Support
- traffic port,
AMC and ARTM Traffic Port
- antistatic wrist strap,
Safety Requirements
- ARTM
- cable requirements,
System Configurations
- connectors,
Advanced Rear Transition Module Connectors (Zone 3)
- description,
System Configurations
- enables access,
System Requirements and Options
- installation,
Install an Advanced Rear Transition Module
- remove,
Remove an ARTM
- support,
Advanced Rear Transition Module Support
- traffic port,
AMC and ARTM Traffic Port
- ATCA system, illustrated,
System Configurations
B
- backplane, connectors,
Backplane Connectors
- backplane extended fabric,
Networking and I/O
- base fabric interface, connection,
Netinstall Boot Device Map
- battery, remove or replace,
Remove or Replace a Battery
- BIOS
- boot from secondary,
Boot From Secondary BIOS
- firmware upgrades,
Networking and I/O
- flash devices,
Networking and I/O
- key mapping,
Emulated Terminal Types and Key Mapping
- launch,
Keys for Directing Output to Remote Systems
- option ROMs,
BIOS Settings
- parameters, changing,
Change BIOS Parameters
- primary, selecting,
Select the BIOS Primary
- PROMs,
Networking and I/O
- screen navigation,
BIOS Settings
- settings,
BIOS Settings
- settings, restoring,
Restore the BIOS Settings
- setup menus,
BIOS Settings
- utility screens,
BIOS Screens
- block diagram,
Block Diagram
- BMR-H8S-ATCA,
I2C Device Mapping
- boot failure,
Networking and I/O
- boot from secondary BIOS,
Boot From Secondary BIOS
- Broadcom switch,
AMC and ARTM Traffic Port
C
- cable requirements, ARTM,
System Configurations
- checksum error,
Networking and I/O
- CLI commands,
ShMM CLI and Commands
- clock interface,
Backplane Connectors
- CMOS RAM,
BIOS Settings
- CMOS settings,
Restore the BIOS Settings
- compact flash
- installation,
Install Compact Flash Card
- interface,
Networking and I/O
- remove,
Remove a Compact Flash Card
- support,
Networking and I/O
- configurations, I/O,
System Configurations
- connectors
- AMC,
On-Board Connectors
- ARTM,
Advanced Rear Transition Module Connectors (Zone 3)
- backplane,
Backplane Connectors
- compact flash,
On-Board Connectors
- configuring,
Configuring Ports and Pins
- data transport,
Backplane Connectors
- DIMMs,
On-Board Connectors
- Ethernet,
Front Connectors
- front,
Front Connectors
- on-board,
On-Board Connectors
- power,
Backplane Connectors
- serial port,
Front Connectors
- USB,
Front Connectors
- Zone 1,
Backplane Connectors
- Zone 2,
Backplane Connectors
- Zone 3,
Advanced Rear Transition Module Connectors (Zone 3)
- cooling,
Required Cooling and Blade Impedance Curve
- Ctrl-key sequences,
Keys for Directing Output to Remote Systems
D
- date, reset,
Reset the System Time and Date
- defective blade server,
Return a Blade Server
- dimensions,
Form-Factor Physical Characteristics
- DIMMs
- empty slots,
Power and Thermal Distribution
- installation,
Install Onboard Memory
- precautions, handling,
Install Onboard Memory
- remove,
Remove Onboard Memory
- diskless client,
System Configurations
- drives, mounted to server,
Networking and I/O
E
F
- factory default settings, stored,
Networking and I/O
- fan trays,
Verify the Fan Trays
- fault origins,
LEDs and Status Indicators
- features,
Features
- firmware upgrades,
Software and Firmware Upgrades
- firmware upgrades, BIOS,
Networking and I/O
- front and side views,
Front and Side Views
- front connectors,
Front Connectors
- FRUID, viewing,
View Electronic Blade Server ID
- full-duplex serial terminal connection,
Connect Cables to a System Console Running Solaris OS
- FWH0,
Networking and I/O
- FWH1,
Networking and I/O