Go to main content

man pages section 5: File Formats

Exit Print View

Updated: Thursday, June 13, 2019
 
 

xorg.conf.d (5)

Name

xorg.conf.d - configuration files for Xorg X server

Synopsis

Please see following description for synopsis

Description

xorg.conf(5)                  File Formats Manual                 xorg.conf(5)



NAME
       xorg.conf, xorg.conf.d - configuration files for Xorg X server

INTRODUCTION
       Xorg  supports several mechanisms for supplying/obtaining configuration
       and run-time parameters: command line options,  environment  variables,
       the  xorg.conf and xorg.conf.d configuration files, auto-detection, and
       fallback defaults. When the same information is supplied in  more  than
       one  way,  the highest precedence mechanism is used. The list of mecha-
       nisms is ordered from highest precedence to lowest. Note that  not  all
       parameters  can be supplied via all methods. The available command line
       options and environment variables (and some defaults) are described  in
       the Xserver(1) and Xorg(1) manual pages. Most configuration file param-
       eters, with their defaults, are described below. Driver and module spe-
       cific  configuration parameters are described in the relevant driver or
       module manual page.

DESCRIPTION
       Xorg uses a configuration file called xorg.conf and files ending in the
       suffix .conf from the directory xorg.conf.d for its initial setup.  The
       xorg.conf configuration file is searched for in  the  following  places
       when the server is started as a normal user:

           /etc/X11/<cmdline>
           /usr/lib/X11/<cmdline>
           /etc/X11/$XORGCONFIG
           /usr/lib/X11/$XORGCONFIG
           /etc/X11/xorg.conf
           /etc/xorg.conf
           /usr/etc/X11/xorg.conf.<hostname>
           /usr/etc/X11/xorg.conf
           /usr/lib/X11/xorg.conf.<hostname>
           /usr/lib/X11/xorg.conf

       where  <cmdline> is a relative path (with no ".." components) specified
       with the -config command line option, $XORGCONFIG is the relative  path
       (with  no  ".." components) specified by that environment variable, and
       <hostname> is the machine's hostname as reported by gethostname(3).

       When the Xorg server is started by the "root"  user,  the  config  file
       search locations are as follows:

           <cmdline>
           /etc/X11/<cmdline>
           /usr/lib/X11/<cmdline>
           $XORGCONFIG
           /etc/X11/$XORGCONFIG
           /usr/lib/X11/$XORGCONFIG
           /etc/X11/xorg.conf
           /etc/xorg.conf
           /usr/etc/X11/xorg.conf.<hostname>
           /usr/etc/X11/xorg.conf
           /usr/lib/X11/xorg.conf.<hostname>
           /usr/lib/X11/xorg.conf

       where  <cmdline>  is  the  path specified with the -config command line
       option (which may be absolute or relative),  $XORGCONFIG  is  the  path
       specified by that environment variable (absolute or relative), $HOME is
       the path specified by  that  environment  variable  (usually  the  home
       directory),  and  <hostname>  is  the machine's hostname as reported by
       gethostname(3).

       Additional configuration files are searched for in the following direc-
       tories when the server is started as a normal user:

           /etc/X11/<cmdline>
           /etc/X11/<cmdline>
           /etc/X11/xorg.conf.d
           /etc/X11/xorg.conf.d

       where  <cmdline> is a relative path (with no ".." components) specified
       with the -configdir command line option.

       When the Xorg server is started by the "root" user, the  config  direc-
       tory search locations are as follows:

           <cmdline>
           /etc/X11/<cmdline>
           /etc/X11/<cmdline>
           /etc/X11/xorg.conf.d
           /etc/X11/xorg.conf.d

       where  <cmdline> is the path specified with the -configdir command line
       option (which may be absolute or relative).

       Finally, configuration files will also be searched for in  a  directory
       reserved  for system use.  This is to separate configuration files from
       the vendor or 3rd party packages from those  of  local  administration.
       These files are found in the following directory:

           /usr/share/X11/xorg.conf.d

       The  xorg.conf  and  xorg.conf.d files are composed of a number of sec-
       tions which may be present in any order, or omitted to use default con-
       figuration values.  Each section has the form:

           Section  "SectionName"
               SectionEntry
               ...
           EndSection

       The section names are:

           Files          File pathnames
           ServerFlags    Server flags
           Module         Dynamic module loading
           Extensions     Extension enabling
           InputDevice    Input device description
           InputClass     Input class description
           OutputClass    Output class description
           Device         Graphics device description
           VideoAdaptor   Xv video adaptor description
           Monitor        Monitor description
           Modes          Video modes descriptions
           Screen         Screen configuration
           ServerLayout   Overall layout
           DRI            DRI-specific configuration
           Vendor         Vendor-specific configuration

       The  following obsolete section names are still recognised for compati-
       bility purposes.  In new config files, the InputDevice  section  should
       be used instead.

           Keyboard       Keyboard configuration
           Pointer        Pointer/mouse configuration

       The old XInput section is no longer recognised.

       The ServerLayout sections are at the highest level.  They bind together
       the input and output devices that will be used in a session.  The input
       devices are described in the InputDevice sections.  Output devices usu-
       ally consist of multiple independent components (e.g., a graphics board
       and  a  monitor).   These multiple components are bound together in the
       Screen sections, and it is these that are referenced by the  ServerLay-
       out section.  Each Screen section binds together a graphics board and a
       monitor.  The graphics boards are described in the Device sections, and
       the monitors are described in the Monitor sections.

       Config  file  keywords  are  case-insensitive,  and  "_" characters are
       ignored.  Most strings (including Option names) are also  case-insensi-
       tive, and insensitive to white space and "_" characters.

       Each  config  file  entry  usually  takes up a single line in the file.
       They consist of a keyword, which is possibly followed by  one  or  more
       arguments,  with the number and types of the arguments depending on the
       keyword.  The argument types are:

           Integer     an integer number in decimal, hex or octal
           Real        a floating point number
           String      a string enclosed in double quote marks (")

       Note: hex integer values must be prefixed with "0x", and  octal  values
       with "0".

       A  special  keyword called Option may be used to provide free-form data
       to various components of the server.  The Option keyword  takes  either
       one  or  two  string  arguments.  The first is the option name, and the
       optional second argument is  the  option  value.   Some  commonly  used
       option value types include:

           Integer     an integer number in decimal, hex or octal
           Real        a floating point number
           String      a sequence of characters
           Boolean     a boolean value (see below)
           Frequency   a frequency value (see below)

       Note  that  all  Option  values,  not just strings, must be enclosed in
       quotes.

       Boolean options may optionally have a value specified.  When  no  value
       is specified, the option's value is TRUE.  The following boolean option
       values are recognised as TRUE:

           1, on, true, yes

       and the following boolean option values are recognised as FALSE:

           0, off, false, no

       If an option name is prefixed with  "No",  then  the  option  value  is
       negated.

       Example: the following option entries are equivalent:

           Option "Accel"   "Off"
           Option "NoAccel"
           Option "NoAccel" "On"
           Option "Accel"   "false"
           Option "Accel"   "no"

       Frequency  option  values  consist  of a real number that is optionally
       followed by one of the following frequency units:

           Hz, k, kHz, M, MHz

       When the unit name is omitted, the correct  units  will  be  determined
       from  the  value  and  the expectations of the appropriate range of the
       value.  It is recommended that the units always be specified when using
       frequency option values to avoid any errors in determining the value.

FILES SECTION
       The  Files  section  is used to specify some path names required by the
       server.  Some of these paths can also be set from the command line (see
       Xserver(1) and Xorg(1)).  The command line settings override the values
       specified in the config file.  The Files section is  optional,  as  are
       all of the entries that may appear in it.

       The entries that can appear in this section are:

       FontPath "path"
              sets  the search path for fonts.  This path is a comma separated
              list of font path elements which the Xorg  server  searches  for
              font databases.  Multiple FontPath entries may be specified, and
              they will be concatenated to build up the fontpath used  by  the
              server.   Font  path  elements  can be absolute directory paths,
              catalogue directories or a font server identifier.  The  formats
              of the later two are explained below:

              Catalogue directories:

                  Catalogue directories can be specified using the prefix cat-
                  alogue: before the directory name. The directory can then be
                  populated  with  symlinks pointing to the real font directo-
                  ries, using the following syntax in the symlink name:

                      <identifier>:[attribute]:pri=<priority>

                  where   <identifier>   is   an   alphanumeric    identifier,
                  [attribute]  is  an  attribute  which  will be passed to the
                  underlying FPE and <priority> is a number used to order  the
                  fontfile FPEs. Examples:

                      75dpi:unscaled:pri=20 -> /usr/share/X11/fonts/75dpi
                      gscript:pri=60 -> /usr/share/fonts/default/ghostscript
                      misc:unscaled:pri=10 -> /usr/share/X11/fonts/misc

              Font server identifiers:

                  Font server identifiers have the form:

                      <trans>/<hostname>:<port-number>

                  where <trans> is the transport type to use to connect to the
                  font server (e.g., unix for UNIX-domain sockets or tcp for a
                  TCP/IP  connection),  <hostname>  is  the  hostname  of  the
                  machine running the font server, and  <port-number>  is  the
                  port  number  that  the font server is listening on (usually
                  7100).

              When this entry is not specified in the config file, the  server
              falls  back to the compiled-in default font path, which contains
              the following font path elements (which can be set inside a cat-
              alogue directory):

                  /usr/share/fonts/X11/misc/
                  /usr/share/fonts/X11/TTF/
                  /usr/share/fonts/X11/OTF/
                  /usr/share/fonts/X11/Type1/
                  /usr/share/fonts/X11/100dpi/
                  /usr/share/fonts/X11/75dpi/

              Font path elements that are found to be invalid are removed from
              the font path when the server starts up.

       ModulePath "path"
              sets the search path for loadable  Xorg  server  modules.   This
              path  is  a  comma  separated list of directories which the Xorg
              server searches for loadable modules loading in the order speci-
              fied.   Multiple  ModulePath  entries may be specified, and they
              will be concatenated to build the module search path used by the
              server.  The default module path is

                  /usr/lib/xorg/modules

       XkbDir "path"
              sets  the base directory for keyboard layout files.  The -xkbdir
              command line option can be used to override this.   The  default
              directory is

                  /usr/share/X11/xkb

SERVERFLAGS SECTION
       In  addition to options specific to this section (described below), the
       ServerFlags section is used to specify some global Xorg server options.
       All  of  the entries in this section are Options, although for compati-
       bility purposes some of the old style  entries  are  still  recognised.
       Those old style entries are not documented here, and using them is dis-
       couraged.  The ServerFlags section is optional, as are the entries that
       may be specified in it.

       Options  specified in this section (with the exception of the "Default-
       ServerLayout" Option) may be overridden by  Options  specified  in  the
       active ServerLayout section.  Options with command line equivalents are
       overridden when their command line equivalent  is  used.   The  options
       recognised by this section are:

       Option "Debug"  "string"
              This  comma-separated  list  provides  a  way to control various
              debugging switches from the config file.  At the moment the only
              defined value is dmabuf_capable which instructs glamor to enable
              some unstable buffer management code.

       Option "DefaultServerLayout"  "layout-id"
              This specifies the default ServerLayout section to  use  in  the
              absence of the -layout command line option.

       Option "NoTrapSignals"  "boolean"
              This  prevents  the  Xorg  server from trapping a range of unex-
              pected fatal signals and exiting  cleanly.   Instead,  the  Xorg
              server  will  die  and  drop core where the fault occurred.  The
              default behaviour is for the Xorg server to  exit  cleanly,  but
              still  drop  a core file.  In general you never want to use this
              option unless you are debugging an Xorg server problem and  know
              how to deal with the consequences.

       Option "DontVTSwitch"  "boolean"
              This  disallows  the  use  of the Ctrl+Alt+Fn sequence (where Fn
              refers to one of the numbered function keys).  That sequence  is
              normally used to switch to another "virtual terminal" on operat-
              ing systems  that  have  this  feature.   When  this  option  is
              enabled,  that key sequence has no special meaning and is passed
              to clients.  Default: off.

       Option "DontZap"  "boolean"
              This disallows the use of the Terminate_Server XKB action  (usu-
              ally  on  Ctrl+Alt+Backspace,  depending  on XKB options).  This
              action is normally used to terminate the Xorg server.  When this
              option is enabled, the action has no effect.  Default: off.

       Option "DontZoom"  "boolean"
              This   disallows   the   use  of  the  Ctrl+Alt+Keypad-Plus  and
              Ctrl+Alt+Keypad-Minus sequences.  These sequences allows you  to
              switch  between video modes.  When this option is enabled, those
              key sequences have no special meaning and are passed to clients.
              Default: off.

       Option "DisableVidModeExtension"  "boolean"
              This  disables  the  parts  of the VidMode extension used by the
              xvidtune client that can be used  to  change  the  video  modes.
              Default: the VidMode extension is enabled.

       Option "AllowNonLocalXvidtune"  "boolean"
              This  allows the xvidtune client (and other clients that use the
              VidMode extension) to connect from another host.  Default: off.

       Option "AllowMouseOpenFail"  "boolean"
              This tells the mousedrv(4) and vmmouse(4) drivers to not  report
              failure if the mouse device can't be opened/initialised.  It has
              no effect on the evdev(4) or other drivers.  Default: false.

       Option "BlankTime"  "time"
              sets the inactivity timeout for the blank phase of  the  screen-
              saver.   time  is  in  minutes.   This is equivalent to the Xorg
              server's -s flag, and the value can be changed at run-time  with
              xset(1).  Default: 10 minutes.

       Option "StandbyTime"  "time"
              sets  the inactivity timeout for the standby phase of DPMS mode.
              time is in minutes, and the value can  be  changed  at  run-time
              with  xset(1).   Default: 10 minutes.  This is only suitable for
              VESA DPMS compatible monitors, and may not be supported  by  all
              video  drivers.   It  is  only enabled for screens that have the
              "DPMS" option set (see the MONITOR section below).

       Option "SuspendTime"  "time"
              sets the inactivity timeout for the suspend phase of DPMS  mode.
              time  is  in  minutes,  and the value can be changed at run-time
              with xset(1).  Default: 10 minutes.  This is only  suitable  for
              VESA  DPMS  compatible monitors, and may not be supported by all
              video drivers.  It is only enabled for  screens  that  have  the
              "DPMS" option set (see the MONITOR section below).

       Option "OffTime"  "time"
              sets  the  inactivity  timeout  for  the off phase of DPMS mode.
              time is in minutes, and the value can  be  changed  at  run-time
              with  xset(1).   Default: 10 minutes.  This is only suitable for
              VESA DPMS compatible monitors, and may not be supported  by  all
              video  drivers.   It  is  only enabled for screens that have the
              "DPMS" option set (see the MONITOR section below).

       Option "MaxClients"  "integer"
              Set the maximum number of clients allowed to connect  to  the  X
              server.  Acceptable values are 64, 128, 256 or 512.

       Option "NoPM"  "boolean"
              Disables something to do with power management events.  Default:
              PM enabled on platforms that support it.

       Option "Xinerama"  "boolean"
              enable or disable XINERAMA extension.  Default is disabled.

       Option "IndirectGLX" "boolean"
              enable or disable indirect GLX contexts. Indirect  GLX  contexts
              are disabled by default.

       Option "DRI2" "boolean"
              enable or disable DRI2. DRI2 is disabled by default.

       Option "GlxVisuals" "string"
              This  option  controls how many GLX visuals the GLX modules sets
              up.  The default value is typical, which will setup up a typical
              subset  of  the GLXFBConfigs provided by the driver as GLX visu-
              als.  Other options are minimal, which will set up  the  minimal
              set  allowed  by  the GLX specification and all which will setup
              GLX visuals for all GLXFBConfigs.

       Option "UseDefaultFontPath" "boolean"
              Include the default font path even if other paths are  specified
              in xorg.conf. If enabled, other font paths are included as well.
              Enabled by default.

       Option "IgnoreABI" "boolean"
              Allow modules built for a  different,  potentially  incompatible
              version of the X server to load. Disabled by default.

       Option "AutoAddDevices" "boolean"
              If  this  option is disabled, then no devices will be added from
              the HAL or udev backends. Enabled by default.

       Option "AutoEnableDevices" "boolean"
              If this option is disabled, then the devices will be added  (and
              the  DevicePresenceNotify  event  sent),  but  not enabled, thus
              leaving policy up to the client.  Enabled by default.

       Option "AutoAddGPU" "boolean"
              If this option is disabled, then no GPU devices  will  be  added
              from  the udev backend. Enabled by default. (May need to be dis-
              abled to setup Xinerama).

       Option "Log" "string"
              This option controls whether the log is flushed and/or synced to
              disk  after  each  message.   Possible values are flush or sync.
              Unset by default.

MODULE SECTION
       The Module section is used to specify which Xorg server modules  should
       be  loaded.   This  section is ignored when the Xorg server is built in
       static form.  The type of modules normally loaded in this  section  are
       Xorg  server  extension  modules.   Most  other module types are loaded
       automatically when they are needed via other  mechanisms.   The  Module
       section is optional, as are all of the entries that may be specified in
       it.

       Entries in this section may be in two forms.  The first and  most  com-
       monly  used  form  is an entry that uses the Load keyword, as described
       here:

       Load  "modulename"
              This instructs the server to load the module called  modulename.
              The  module name given should be the module's standard name, not
              the module file name.  The standard name is case-sensitive,  and
              does  not  include  the "lib" or "cyg" prefixes, or the ".so" or
              ".dll" suffixes.

              Example: the DRI extension module can be loaded with the follow-
              ing entry:

                  Load "dri"

       Disable  "modulename"
              This  instructs the server to not load the module called module-
              name.  Some modules are loaded by default  in  the  server,  and
              this  overrides that default. If a Load instruction is given for
              the same module, it overrides the Disable  instruction  and  the
              module  is  loaded. The module name given should be the module's
              standard name, not the  module  file  name.  As  with  the  Load
              instruction,  the  standard name is case-sensitive, and does not
              include the "lib" prefix, or the ".a", ".o", or ".so" suffixes.

       The second form of entry is a  SubSection,  with  the  subsection  name
       being the module name, and the contents of the SubSection being Options
       that are passed to the module when it is loaded.

       Example: the extmod module (which contains  a  miscellaneous  group  of
       server  extensions)  can be loaded, with the XFree86-DGA extension dis-
       abled by using the following entry:

           SubSection "extmod"
              Option  "omit XFree86-DGA"
           EndSubSection

       Modules are searched for in each directory specified in the  ModulePath
       search  path, and in the drivers, extensions, input, internal, and mul-
       timedia subdirectories of each of those directories.   In  addition  to
       this,  operating  system  specific  subdirectories of all the above are
       searched first if they exist.

       To see what extension modules are available, check the extensions  sub-
       directory under:

           /usr/lib/xorg/modules

       The  "extmod", "dbe", "dri", "dri2", "glx", and "record" extension mod-
       ules are loaded automatically, if they  are  present,  unless  disabled
       with  "Disable"  entries.   It  is  recommended  that at very least the
       "extmod" extension module be loaded.  If it isn't, some  commonly  used
       server extensions (like the SHAPE extension) will not be available.

EXTENSIONS SECTION
       The Extensions section is used to specify which X11 protocol extensions
       should be enabled or disabled.  The Extensions section is optional,  as
       are all of the entries that may be specified in it.

       Entries  in  this section are listed as Option statements with the name
       of the extension as the first argument, and a boolean value as the sec-
       ond.   The extension name is case-sensitive, and matches the form shown
       in the output of "Xorg -extension ?".

              Example: the MIT-SHM extension can be disabled with the  follow-
              ing entry:

                  Section "Extensions"
                      Option "MIT-SHM" "Disable"
                  EndSection

INPUTDEVICE SECTION
       The  config  file  may  have  multiple  InputDevice sections.  Recent X
       servers employ HAL or udev backends for input  device  enumeration  and
       input  hotplugging.  It is usually not necessary to provide InputDevice
       sections in the xorg.conf if hotplugging is in use (i.e. AutoAddDevices
       is  enabled). If hotplugging is enabled, InputDevice sections using the
       mouse, kbd and vmmouse driver will be ignored.

       If hotplugging is disabled, there will normally be at  least  two:  one
       for  the  core  (primary)  keyboard  and  one for the core pointer.  If
       either of these two is missing, a default configuration for the missing
       ones will be used. In the absence of an explicitly specified core input
       device, the first InputDevice marked as CorePointer  (or  CoreKeyboard)
       is  used.   If there is no match there, the first InputDevice that uses
       the "mouse" (or "kbd") driver is used.  The final fallback  is  to  use
       built-in  default  configurations.  Currently the default configuration
       may not work as expected on all platforms.

       InputDevice sections have the following format:

           Section "InputDevice"
               Identifier "name"
               Driver     "inputdriver"
               options
               ...
           EndSection

       The Identifier and Driver entries are required in all InputDevice  sec-
       tions.  All other entries are optional.

       The  Identifier  entry specifies the unique name for this input device.
       The Driver entry specifies the name of the driver to use for this input
       device.   When  using  the  loadable  server,  the  input driver module
       "inputdriver" will be loaded for each active InputDevice  section.   An
       InputDevice  section  is  considered  active  if it is referenced by an
       active ServerLayout section, if it is referenced by  the  -keyboard  or
       -pointer  command  line options, or if it is selected implicitly as the
       core pointer or keyboard device in the absence of such explicit  refer-
       ences.  The most commonly used input drivers are evdev(4) on Linux sys-
       tems, and kbd(4) and mousedrv(4) on other platforms.

       InputDevice sections recognise some driver-independent  Options,  which
       are described here.  See the individual input driver manual pages for a
       description of the device-specific options.

       Option "AutoServerLayout"  "boolean"
              Always add the device to the ServerLayout section used  by  this
              instance  of the server. This affects implied layouts as well as
              explicit layouts specified in the configuration  and/or  on  the
              command line.

       Option "CorePointer"
              Deprecated, see Floating

       Option "CoreKeyboard"
              Deprecated, see Floating

       Option "AlwaysCore"  "boolean"
              Deprecated, see Floating

       Option "SendCoreEvents"  "boolean"
              Deprecated, see Floating


       Option "Floating"  "boolean"
              When  enabled,  the input device is set up floating and does not
              report events through any master device or control a cursor. The
              device  is only available to clients using the X Input Extension
              API. This option is disabled  by  default.   The  options  Core-
              Pointer,  CoreKeyboard,  AlwaysCore, and SendCoreEvents, are the
              inverse of option Floating (i.e.  SendCoreEvents "on" is equiva-
              lent to Floating "off" ).

              This  option controls the startup behavior only, a device may be
              reattached or set floating at runtime.

       Option "TransformationMatrix" "a b c d e f g h i"
              Specifies the  3x3  transformation  matrix  for  absolute  input
              devices. The input device will be bound to the area given in the
              matrix.  In most configurations, "a" and "e" specify  the  width
              and  height  of the area the device is bound to, and "c" and "f"
              specify the x and y offset of the area.  The value range is 0 to
              1,  where  1  represents the width or height of all root windows
              together, 0.5 represents half the area, etc. The  values  repre-
              sent  a  3x3  matrix,  with the first, second and third group of
              three values representing the first, second and third row of the
              matrix,  respectively.   The identity matrix is "1 0 0 0 1 0 0 0
              1".

   POINTER ACCELERATION
       For pointing devices, the following options control how the pointer  is
       accelerated or decelerated with respect to physical device motion. Most
       of these can be adjusted at runtime, see the  xinput(1)  man  page  for
       details.  Only  the  most  important acceleration options are discussed
       here.

       Option "AccelerationProfile"  "integer"
              Select the profile. In layman's terms, the  profile  constitutes
              the "feeling" of the acceleration. More formally, it defines how
              the transfer function (actual acceleration as a function of cur-
              rent  device velocity and acceleration controls) is constructed.
              This is mainly a matter of personal preference.

              0      classic (mostly compatible)
             -1      none (only constant deceleration is applied)
              1      device-dependent
              2      polynomial (polynomial function)
              3      smooth linear (soft knee, then linear)
              4      simple (normal when slow, otherwise accelerated)
              5      power (power function)
              6      linear (more speed, more acceleration)
              7      limited (like linear, but maxes out at threshold)

       Option "ConstantDeceleration"  "real"
              Makes the pointer go deceleration times slower than normal. Most
              useful for high-resolution devices. A value between 0 and 1 will
              speed up the pointer.

       Option "AdaptiveDeceleration"  "real"
              Allows to actually decelerate the pointer when  going  slow.  At
              most,  it  will  be  adaptive deceleration times slower. Enables
              precise pointer placement without sacrificing speed.

       Option "AccelerationScheme"  "string"
              Selects the scheme, which is the underlying algorithm.

              predictable   default algorithm (behaving more predictable)
              lightweight   old acceleration code (as specified in the X protocol spec)
              none          no acceleration or deceleration

       Option "AccelerationNumerator"  "integer"

       Option "AccelerationDenominator"  "integer"
              Set numerator and denominator of the  acceleration  factor.  The
              acceleration  factor  is a rational which, together with thresh-
              old, can be used to tweak profiles to suit the users needs.  The
              simple  and limited profiles use it directly (i.e. they acceler-
              ate by the factor), for other profiles it  should  hold  that  a
              higher acceleration factor leads to a faster pointer. Typically,
              1 is unaccelerated and values up to 5 are sensible.

       Option "AccelerationThreshold"  "integer"
              Set the threshold, which is roughly the velocity (usually device
              units  per 10 ms) required for acceleration to become effective.
              The precise effect varies with the profile however.


INPUTCLASS SECTION
       The config file may have multiple InputClass sections.  These  sections
       are optional and are used to provide configuration for a class of input
       devices as they are automatically added. An input device can match more
       than  one  InputClass  section. Each class can override settings from a
       previous class, so it is best to arrange the  sections  with  the  most
       generic matches first.

       InputClass sections have the following format:

           Section "InputClass"
               Identifier  "name"
               entries
               ...
               options
               ...
           EndSection

       The Identifier entry is required in all InputClass sections.  All other
       entries are optional.

       The Identifier entry specifies the unique name for  this  input  class.
       The Driver entry specifies the name of the driver to use for this input
       device.  After all classes have been examined, the "inputdriver" module
       from  the  first  Driver  entry will be enabled when using the loadable
       server.

       When an input device is automatically added,  its  characteristics  are
       checked  against  all  InputClass  sections.  Each  section can contain
       optional entries to narrow the match of  the  class.  If  none  of  the
       optional  entries  appear,  the  InputClass section is generic and will
       match any input device. If more than one of these entries appear,  they
       all must match for the configuration to apply.

       There  are  two types of match entries used in InputClass sections. The
       first allows various tokens to be matched  against  attributes  of  the
       device.  An entry can be constructed to match attributes from different
       devices by separating arguments with a '|' character. Multiple  entries
       of the same type may be supplied to add multiple matching conditions on
       the same attribute. For example:

           Section "InputClass"
               Identifier   "My Class"
               # product string must contain example and
               # either gizmo or gadget
               MatchProduct "example"
               MatchProduct "gizmo|gadget"
               NoMatchDriver "drivername"
               ...
           EndSection

       MatchProduct  "matchproduct"
              This entry can be used to check if the substring  "matchproduct"
              occurs in the device's product name.

       MatchVendor  "matchvendor"
              This  entry  can be used to check if the substring "matchvendor"
              occurs in the device's vendor name.

       MatchDevicePath "matchdevice"
              This entry can be used to check if the device file  matches  the
              "matchdevice" pathname pattern.

       MatchOS "matchos"
              This  entry can be used to check if the operating system matches
              the case-insensitive "matchos" string. This entry is  only  sup-
              ported on platforms providing the uname(2) system call.

       MatchPnPID "matchpnp"
              The  device's  Plug and Play (PnP) ID can be checked against the
              "matchpnp" shell wildcard pattern.

       MatchUSBID "matchusb"
              The device's USB ID can be checked against the "matchusb"  shell
              wildcard pattern. The ID is constructed as lowercase hexadecimal
              numbers separated by a ':'. This  is  the  same  format  as  the
              lsusb(8) program.

       MatchDriver "matchdriver"
              Check  the  case-sensitive string "matchdriver" against the cur-
              rently configured driver of the  device.  Ordering  of  sections
              using this entry is important since it will not match unless the
              driver has been set by the config backend or a  previous  Input-
              Class section.

       MatchTag "matchtag"
              This  entry  can be used to check if tags assigned by the config
              backend matches the "matchtag" pattern. A match is found  if  at
              least  one  of the tags given in "matchtag" matches at least one
              of the tags assigned by the backend.

       MatchLayout "matchlayout"
              Check the case-sensitive string "matchlayout" against  the  cur-
              rently  active ServerLayout section. The empty string "" matches
              an implicit layout which appears if no named  ServerLayout  sec-
              tions have been found.

       The  above  directives  have equivalents for negative matching with the
       NoMatchProduct, NoMatchVendor, NoMatchDevicePath, NoMatchOS, NoMatchPn-
       PID,  NoMatchUSBID, NoMatchDriver, NoMatchTag, and NoMatchLayout direc-
       tives. These NoMatch directives match if the subsequent  match  is  not
       met by the device.

       The  second  type of entry is used to match device types. These entries
       take a boolean argument similar to Option entries.

       MatchIsKeyboard     "bool"

       MatchIsPointer      "bool"

       MatchIsJoystick     "bool"

       MatchIsTablet       "bool"

       MatchIsTabletPad    "bool"

       MatchIsTouchpad     "bool"

       MatchIsTouchscreen  "bool"

       When an input device has been matched to the  InputClass  section,  any
       Option  entries  are  applied  to  the  device. One InputClass specific
       Option is recognized. See the InputDevice section above for a  descrip-
       tion of the remaining Option entries.

       Option "Ignore" "boolean"
              This  optional entry specifies that the device should be ignored
              entirely, and not added to the server. This can be  useful  when
              the  device is handled by another program and no X events should
              be generated.

OUTPUTCLASS SECTION
       The config file may have multiple OutputClass sections.  These sections
       are  optional and are used to provide configuration for a class of out-
       put devices as they are automatically  added.   An  output  device  can
       match  more than one OutputClass section.  Each class can override set-
       tings from a previous class, so it is best to arrange the sections with
       the most generic matches first.

       OutputClass sections have the following format:

           Section "OutputClass"
               Identifier  "name"
               entries
               ...
           EndSection

       The  Identifier  entry  is  required  in all OutputClass sections.  All
       other entries are optional.

       The Identifier entry specifies the unique name for this  output  class.
       The  Driver entry specifies the name of the driver to use for this out-
       put device.  After all classes have been examined,  the  "outputdriver"
       module from the first Driver entry will be enabled when using the load-
       able server.

       When an output device is automatically added, its  characteristics  are
       checked  against  all  OutputClass  sections.  Each section can contain
       optional entries to narrow the match of the  class.   If  none  of  the
       optional  entries  appear,  the OutputClass section is generic and will
       match any output device.  If more than one  of  these  entries  appear,
       they all must match for the configuration to apply.

       The  following  list of tokens can be matched against attributes of the
       device.  An entry can be constructed to match attributes from different
       devices by separating arguments with a '|' character.

       For example:

           Section "OutputClass"
               Identifier   "My Class"
               # kernel driver must be either foo or bar
               MatchDriver "foo|bar"
               ...
           EndSection

       MatchDriver "matchdriver"
              Check the case-sensitive string "matchdriver" against the kernel
              driver of the device.

       When an output device has been matched to the OutputClass section,  any
       Option  entries  are  applied  to  the device. One OutputClass specific
       Option is recognized. See the Device section below for a description of
       the remaining Option entries.

       Option "PrimaryGPU" "boolean"
              This  option specifies that the matched device should be treated
              as the primary GPU, replacing the selection of the GPU  used  as
              output by the firmware. If multiple output devices match an Out-
              putClass section with the PrimaryGPU option set, the  first  one
              enumerated becomes the primary GPU.

       A  OutputClass  Section  may contain ModulePath entries. When an output
       device matches an OutputClass section, any ModulePath entries  in  that
       OutputClass  are pre-pended to the search path for loadable Xorg server
       modules. See ModulePath in the Files section for more info.

DEVICE SECTION
       The config file may have multiple Device sections.  There  must  be  at
       least one, for the video card being used.

       Device sections have the following format:

           Section "Device"
               Identifier "name"
               Driver     "driver"
               entries
               ...
           EndSection

       The  Identifier and Driver entries are required in all Device sections.
       All other entries are optional.

       The Identifier entry  specifies  the  unique  name  for  this  graphics
       device.   The  Driver entry specifies the name of the driver to use for
       this graphics device.  When using the loadable server, the driver  mod-
       ule  "driver"  will be loaded for each active Device section.  A Device
       section is considered active if it is referenced by  an  active  Screen
       section.

       Device  sections recognise some driver-independent entries and Options,
       which  are  described  here.   Not  all  drivers  make  use  of   these
       driver-independent  entries,  and  many  of those that do don't require
       them to be specified because the information is auto-detected.  See the
       individual  graphics  driver manual pages for further information about
       this, and for a description of the device-specific options.  Note  that
       most  of  the  Options  listed  here (but not the other entries) may be
       specified in the Screen section instead of here in the Device section.

       BusID  "bus-id"
              This specifies the bus  location  of  the  graphics  card.   For
              PCI/AGP    cards,    the    bus-id    string    has   the   form
              PCI:bus@domain:device:function  (e.g.,  "PCI:1@0:0:0"  might  be
              appropriate for an AGP card). The "@domain" part can be left out
              for PCI domain 0. This field is usually optional in  single-head
              configurations  when using the primary graphics card.  In multi-
              head configurations, or when using a secondary graphics card  in
              a  single-head configuration, this entry is mandatory.  Its main
              purpose is to make an unambiguous connection between the  device
              section  and  the hardware it is representing.  This information
              can usually be found by running the pciaccess tool scanpci.

       Screen  number
              This option is mandatory for cards where a single PCI entity can
              drive more than one display (i.e., multiple CRTCs sharing a sin-
              gle graphics accelerator and video memory).  One Device  section
              is  required  for each head, and this parameter determines which
              head each of the Device sections applies to.  The  legal  values
              of  number  range  from  0  to one less than the total number of
              heads per entity.  Most drivers require that the primary  screen
              (0) be present.

       Chipset  "chipset"
              This  usually  optional  entry specifies the chipset used on the
              graphics board.  In  most  cases  this  entry  is  not  required
              because  the  drivers  will  probe the hardware to determine the
              chipset type.  Don't specify it unless the driver-specific docu-
              mentation recommends that you do.

       Ramdac  "ramdac-type"
              This  optional  entry  specifies  the type of RAMDAC used on the
              graphics board.  This is only used by a few of the drivers,  and
              in  most cases it is not required because the drivers will probe
              the hardware to determine the RAMDAC type where possible.  Don't
              specify  it  unless the driver-specific documentation recommends
              that you do.

       DacSpeed  speed

       DacSpeed  speed-8 speed-16 speed-24 speed-32
              This optional entry specifies the RAMDAC speed rating (which  is
              usually printed on the RAMDAC chip).  The speed is in MHz.  When
              one value is given, it applies to all framebuffer  pixel  sizes.
              When  multiple  values  are given, they apply to the framebuffer
              pixel sizes 8, 16, 24 and 32 respectively.  This is not used  by
              many drivers, and only needs to be specified when the speed rat-
              ing of the RAMDAC is different from the  defaults  built  in  to
              driver,  or  when  the  driver  can't  auto-detect  the  correct
              defaults.  Don't specify it unless the driver-specific  documen-
              tation recommends that you do.

       Clocks  clock ...
              specifies the pixel that are on your graphics board.  The clocks
              are in MHz, and may be specified as  a  floating  point  number.
              The value is stored internally to the nearest kHz.  The ordering
              of the clocks is important.  It must match the  order  in  which
              they  are selected on the graphics board.  Multiple Clocks lines
              may be specified, and each is concatenated  to  form  the  list.
              Most  drivers do not use this entry, and it is only required for
              some older boards with non-programmable clocks.   Don't  specify
              this  entry  unless the driver-specific documentation explicitly
              recommends that you do.

       ClockChip  "clockchip-type"
              This optional entry is used to specify the clock  chip  type  on
              graphics boards which have a programmable clock generator.  Only
              a few  Xorg  drivers  support  programmable  clock  chips.   For
              details, see the appropriate driver manual page.

       VideoRam  mem
              This  optional  entry  specifies the amount of video ram that is
              installed on the graphics board.  This is  measured  in  kBytes.
              In  most  cases  this  is  not  required because the Xorg server
              probes the graphics  board  to  determine  this  quantity.   The
              driver-specific  documentation  should indicate when it might be
              needed.

       MemBase  baseaddress
              This optional entry specifies  the  memory  base  address  of  a
              graphics board's linear frame buffer.  This entry is not used by
              many drivers, and it should only be specified if the driver-spe-
              cific documentation recommends it.

       IOBase  baseaddress
              This  optional  entry specifies the IO base address.  This entry
              is not used by many drivers, and it should only be specified  if
              the driver-specific documentation recommends it.

       ChipID  id
              This  optional  entry  specifies a numerical ID representing the
              chip type.  For PCI cards, it is usually the  device  ID.   This
              can be used to override the auto-detection, but that should only
              be done when the driver-specific documentation recommends it.

       ChipRev  rev
              This optional entry specifies the chip  revision  number.   This
              can be used to override the auto-detection, but that should only
              be done when the driver-specific documentation recommends it.

       MatchSeat  seat-id
              Only apply this Device section if  X  server  was  started  with
              -seat seat-id option.

       Option "ModeDebug" "boolean"
              Enable  printing of additional debugging information about mode-
              setting to the server log.

       Option "PreferCloneMode" "boolean"
              If enabled, bring up monitors of a screen in clone mode  instead
              of  horizontal extended layout by default. (Defaults to off; the
              video driver can change the default value, but this  option  can
              always override it)

       Options
              Option  flags  may  be  specified in the Device sections.  These
              include driver-specific options and driver-independent  options.
              The  former  are described in the driver-specific documentation.
              Some of the latter are described below in the section about  the
              Screen section, and they may also be included here.


VIDEOADAPTOR SECTION
       Nobody wants to say how this works.  Maybe nobody knows ...


MONITOR SECTION
       The  config file may have multiple Monitor sections.  There should nor-
       mally be at least one, for the monitor being used, but a  default  con-
       figuration will be created when one isn't specified.

       Monitor sections have the following format:

           Section "Monitor"
               Identifier "name"
               entries
               ...
           EndSection

       The only mandatory entry in a Monitor section is the Identifier entry.

       The  Identifier  entry specifies the unique name for this monitor.  The
       Monitor section may be used to provide information about the specifica-
       tions  of  the monitor, monitor-specific Options, and information about
       the video modes to use with the monitor.

       With RandR 1.2-enabled drivers, monitor sections may be  tied  to  spe-
       cific  outputs of the video card.  Using the name of the output defined
       by the video driver plus the identifier of a monitor section, one asso-
       ciates  a  monitor  section  with  an output by adding an option to the
       Device section in the following format:

       Option "Monitor-outputname" "monitorsection"

       (for example, Option "Monitor-VGA" "VGA monitor" for a VGA output)

       In the absence of specific association of monitor sections to  outputs,
       if  a  monitor  section is present the server will associate it with an
       output to preserve compatibility for  previous  single-head  configura-
       tions.

       Specifying  video modes is optional because the server will use the DDC
       or other information provided by the monitor to automatically configure
       the  list  of  modes available.  When modes are specified explicitly in
       the Monitor section (with the Mode, ModeLine,  or  UseModes  keywords),
       built-in  modes  with  the same names are not included.  Built-in modes
       with different names are, however, still implicitly included, when they
       meet the requirements of the monitor.

       The entries that may be used in Monitor sections are described below.

       VendorName  "vendor"
              This optional entry specifies the monitor's manufacturer.

       ModelName  "model"
              This optional entry specifies the monitor's model.

       HorizSync  horizsync-range
              gives  the  range(s) of horizontal sync frequencies supported by
              the monitor.  horizsync-range may be a comma separated  list  of
              either  discrete  values or ranges of values.  A range of values
              is two values separated by a dash.  By default the values are in
              units  of  kHz.  They may be specified in MHz or Hz if MHz or Hz
              is added to the end of the line.  The data given here is used by
              the Xorg server to determine if video modes are within the spec-
              ifications of the monitor.  This information should be available
              in  the monitor's handbook.  If this entry is omitted, a default
              range of 28-33kHz is used.

       VertRefresh  vertrefresh-range
              gives the range(s) of vertical refresh frequencies supported  by
              the monitor.  vertrefresh-range may be a comma separated list of
              either discrete values or ranges of values.  A range  of  values
              is two values separated by a dash.  By default the values are in
              units of Hz.  They may be specified in MHz or kHz if MHz or  kHz
              is added to the end of the line.  The data given here is used by
              the Xorg server to determine if video modes are within the spec-
              ifications of the monitor.  This information should be available
              in the monitor's handbook.  If this entry is omitted, a  default
              range of 43-72Hz is used.

       DisplaySize  width height
              This  optional entry gives the width and height, in millimetres,
              of the picture area of the monitor.  If given this  is  used  to
              calculate the horizontal and vertical pitch (DPI) of the screen.

       Gamma  gamma-value

       Gamma  red-gamma green-gamma blue-gamma
              This  is an optional entry that can be used to specify the gamma
              correction for the monitor.  It may be  specified  as  either  a
              single value or as three separate RGB values.  The values should
              be in the range 0.1 to 10.0, and the default is  1.0.   Not  all
              drivers are capable of using this information.

       UseModes  "modesection-id"
              Include the set of modes listed in the Modes section called mod-
              esection-id.  This makes all of the modes defined in  that  sec-
              tion available for use by this monitor.

       Mode  "name"
              This is an optional multi-line entry that can be used to provide
              definitions for video modes for the monitor.  In most cases this
              isn't  necessary because the built-in set of VESA standard modes
              will be sufficient.  The Mode keyword indicates the start  of  a
              multi-line video mode description.  The mode description is ter-
              minated with the EndMode keyword.  The mode description consists
              of the following entries:

              DotClock  clock
                  is the dot (pixel) clock rate to be used for the mode.

              HTimings  hdisp hsyncstart hsyncend htotal
                  specifies the horizontal timings for the mode.

              VTimings  vdisp vsyncstart vsyncend vtotal
                  specifies the vertical timings for the mode.

              Flags  "flag" ...
                  specifies  an optional set of mode flags, each of which is a
                  separate string in  double  quotes.   "Interlace"  indicates
                  that  the mode is interlaced.  "DoubleScan" indicates a mode
                  where each scanline is doubled.  "+HSync" and  "-HSync"  can
                  be  used  to  select  the  polarity  of  the  HSync  signal.
                  "+VSync" and "-VSync" can be used to select the polarity  of
                  the  VSync  signal.  "Composite" can be used to specify com-
                  posite sync on hardware where this is supported.   Addition-
                  ally, on some hardware, "+CSync" and "-CSync" may be used to
                  select the composite sync polarity.

              HSkew  hskew
                  specifies the number of pixels (towards the  right  edge  of
                  the  screen)  by  which  the  display enable signal is to be
                  skewed.  Not all drivers use this information.  This  option
                  might  become  necessary  to override the default value sup-
                  plied by the server (if  any).   "Roving"  horizontal  lines
                  indicate  this value needs to be increased.  If the last few
                  pixels on a scan line appear on the left of the screen, this
                  value should be decreased.

              VScan  vscan
                  specifies  the  number  of times each scanline is painted on
                  the screen.  Not all drivers use this  information.   Values
                  less  than 1 are treated as 1, which is the default.  Gener-
                  ally, the "DoubleScan" Flag  mentioned  above  doubles  this
                  value.

       ModeLine  "name" mode-description
              This  entry  is a more compact version of the Mode entry, and it
              also can be used to specify video modes for the  monitor.   This
              is  a  single  line  format for specifying video modes.  In most
              cases this isn't necessary because  the  built-in  set  of  VESA
              standard modes will be sufficient.

              The  mode-description  is  in  four sections, the first three of
              which are mandatory.  The first is the dot (pixel) clock.   This
              is  a single number specifying the pixel clock rate for the mode
              in MHz.  The second section is a list of four numbers specifying
              the  horizontal  timings.   These  numbers are the hdisp, hsync-
              start, hsyncend, and htotal values.  The third section is a list
              of  four numbers specifying the vertical timings.  These numbers
              are the vdisp, vsyncstart, vsyncend,  and  vtotal  values.   The
              final  section  is a list of flags specifying other characteris-
              tics of the mode.  Interlace indicates that the mode  is  inter-
              laced.   DoubleScan indicates a mode where each scanline is dou-
              bled.  +HSync and -HSync can be used to select the  polarity  of
              the  HSync  signal.  +VSync and -VSync can be used to select the
              polarity of the VSync signal.  Composite can be used to  specify
              composite  sync  on hardware where this is supported.  Addition-
              ally, on some hardware, +CSync and -CSync may be used to  select
              the  composite  sync polarity.  The HSkew and VScan options men-
              tioned above in the Mode entry  description  can  also  be  used
              here.

       Option "DPMS" "bool"
              This  option  controls whether the server should enable the DPMS
              extension for power management for this screen.  The default  is
              to enable the extension.

       Option "SyncOnGreen" "bool"
              This  option  controls  whether  the video card should drive the
              sync signal on the green color pin.  Not all cards support  this
              option,  and  most  monitors  do not require it.  The default is
              off.

       Option "Primary" "bool"
              This optional entry specifies that the monitor should be treated
              as the primary monitor. (RandR 1.2-supporting drivers only)

       Option "PreferredMode" "name"
              This  optional  entry  specifies a mode to be marked as the pre-
              ferred initial mode of the monitor.  (RandR 1.2-supporting driv-
              ers only)

       Option "ZoomModes" "name name ..."
              This  optional entry specifies modes to be marked as zoom modes.
              It is possible to switch to  the  next  and  previous  mode  via
              Ctrl+Alt+Keypad-Plus  and Ctrl+Alt+Keypad-Minus.  All these key-
              pad available modes are selected  from  the  screen  mode  list.
              This  list  is  a  copy of the compatibility output monitor mode
              list.  Since this output is the output connected to  the  lowest
              dot-area monitor, as determined from its largest size mode, that
              monitor defines the available zoom modes.  (RandR 1.2-supporting
              drivers only)

       Option "Position" "x y"
              This optional entry specifies the position of the monitor within
              the X screen.  (RandR 1.2-supporting drivers only)

       Option "LeftOf" "output"
              This optional entry specifies that the monitor should  be  posi-
              tioned  to  the  left  of  the output (not monitor) of the given
              name.  (RandR 1.2-supporting drivers only)

       Option "RightOf" "output"
              This optional entry specifies that the monitor should  be  posi-
              tioned  to  the  right  of the output (not monitor) of the given
              name.  (RandR 1.2-supporting drivers only)

       Option "Above" "output"
              This optional entry specifies that the monitor should  be  posi-
              tioned above the output (not monitor) of the given name.  (RandR
              1.2-supporting drivers only)

       Option "Below" "output"
              This optional entry specifies that the monitor should  be  posi-
              tioned below the output (not monitor) of the given name.  (RandR
              1.2-supporting drivers only)

       Option "Enable" "bool"
              This optional entry specifies  whether  the  monitor  should  be
              turned  on  at  startup.  By default, the server will attempt to
              enable all connected monitors.   (RandR  1.2-supporting  drivers
              only)

       Option "DefaultModes" "bool"
              This optional entry specifies whether the server should add sup-
              ported default modes to the list of modes offered on this  moni-
              tor.  By  default, the server will add default modes; you should
              only disable this if you can guarantee that EDID will be  avail-
              able  at  all times, or if you have added custom modelines which
              the server can use.  (RandR 1.2-supporting drivers only)

       Option "MinClock" "frequency"
              This optional entry specifies the minimum  dot  clock,  in  kHz,
              that is supported by the monitor.

       Option "MaxClock" "frequency"
              This  optional  entry  specifies  the maximum dot clock, in kHz,
              that is supported by the monitor.

       Option "Ignore" "bool"
              This optional entry specifies that the monitor should be ignored
              entirely, and not reported through RandR.  This is useful if the
              hardware reports the  presence  of  outputs  that  don't  exist.
              (RandR 1.2-supporting drivers only)

       Option "Rotate" "rotation"
              This  optional entry specifies the initial rotation of the given
              monitor.   Valid  values  for  rotation  are  "normal",  "left",
              "right", and "inverted".  (RandR 1.2-supporting drivers only)


MODES SECTION
       The  config file may have multiple Modes sections, or none.  These sec-
       tions provide a way of defining sets of video  modes  independently  of
       the  Monitor  sections.   Monitor  sections may include the definitions
       provided in these sections by using  the  UseModes  keyword.   In  most
       cases  the Modes sections are not necessary because the built-in set of
       VESA standard modes will be sufficient.

       Modes sections have the following format:

           Section "Modes"
               Identifier "name"
               entries
               ...
           EndSection

       The Identifier entry specifies the unique name for  this  set  of  mode
       descriptions.   The  other  entries permitted in Modes sections are the
       Mode and ModeLine entries that are described above in the Monitor  sec-
       tion.

SCREEN SECTION
       The  config  file  may have multiple Screen sections.  There must be at
       least one, for the "screen" being  used.   A  "screen"  represents  the
       binding  of  a  graphics device (Device section) and a monitor (Monitor
       section).  A Screen section is considered "active" if it is  referenced
       by  an  active  ServerLayout  section  or  by  the -screen command line
       option.  If neither of those is present, the first Screen section found
       in the config file is considered the active one.

       Screen sections have the following format:

           Section "Screen"
               Identifier "name"
               Device     "devid"
               GPUDevice  "devid"
               Monitor    "monid"
               entries
               ...
               SubSection "Display"
                  entries
                  ...
               EndSubSection
               ...
           EndSection

       The Identifier entry is mandatory.  All others are optional.

       The  Identifier  entry  specifies the unique name for this screen.  The
       Screen section provides  information  specific  to  the  whole  screen,
       including screen-specific Options.  In multi-head configurations, there
       will be multiple active  Screen  sections,  one  for  each  head.   The
       entries available for this section are:

       Device  "device-id"
              This  entry  specifies  the  Device  section to be used for this
              screen.  When multiple graphics cards are present, this is  what
              ties  a specific card to a screen.  The device-id must match the
              Identifier of a Device section in the config file.

       GPUDevice  "device-id"
              This entry specifies the Device section to be  used  as  a  sec-
              ondary GPU device for this screen.  When multiple graphics cards
              are present, this is what ties a specific secondary  card  to  a
              screen.   The  device-id  must  match the Identifier of a Device
              section in the config file. This can be specified up to 4  times
              for a single screen.

       Monitor  "monitor-id"
              specifies  which  monitor  description  is  to  be used for this
              screen.  If a Monitor name is not specified, a default  configu-
              ration  is  used.   Currently  the default configuration may not
              function as expected on all platforms.

       VideoAdaptor  "xv-id"
              specifies an optional Xv video adaptor description  to  be  used
              with this screen.

       DefaultDepth  depth
              specifies  which  color  depth the server should use by default.
              The -depth command line option can be used to override this.  If
              neither  is specified, the default depth is driver-specific, but
              in most cases is 8.

       DefaultFbBpp  bpp
              specifies which framebuffer  layout  to  use  by  default.   The
              -fbbpp  command  line  option  can be used to override this.  In
              most cases the driver will chose  the  best  default  value  for
              this.   The only case where there is even a choice in this value
              is for depth 24, where some hardware supports both a  packed  24
              bit framebuffer layout and a sparse 32 bit framebuffer layout.

       MatchSeat  seat-id
              Only  apply  this  Screen  section  if X server was started with
              -seat seat-id option.

       Options
              Various Option flags may be specified  in  the  Screen  section.
              Some  are  driver-specific and are described in the driver docu-
              mentation.  Others are driver-independent, and  will  eventually
              be described here.

       Option "Accel"
              Enables 2D hardware acceleration.  This option is on by default,
              but it may be necessary to turn it off if there are bugs in  the
              driver.   There are many options to disable specific accelerated
              operations, listed below.  Note that disabling an operation will
              have  no effect if the operation is not accelerated (whether due
              to lack of support in the hardware or in the driver).

       Option "GlxVendorLibrary" "string"
              This option specifies a space-separated list  of  OpenGL  vendor
              libraries  to  use for the screen. This may be used to select an
              alternate implementation for development, debugging,  or  alter-
              nate feature sets.  Default: mesa.

       Option "InitPrimary" "boolean"
              Use  the  Int10  module to initialize the primary graphics card.
              Normally, only secondary cards are soft-booted using  the  Int10
              module,  as the primary card has already been initialized by the
              BIOS at boot time.  Default: false.

       Option "NoInt10" "boolean"
              Disables the Int10 module, a module that uses the int10 call  to
              the BIOS of the graphics card to initialize it.  Default: false.

       Each  Screen section may optionally contain one or more Display subsec-
       tions.  Those subsections provide  depth/fbbpp  specific  configuration
       information,  and the one chosen depends on the depth and/or fbbpp that
       is being used  for  the  screen.   The  Display  subsection  format  is
       described in the section below.


DISPLAY SUBSECTION
       Each  Screen  section  may  have  multiple  Display  subsections.   The
       "active" Display subsection is the first that matches the depth  and/or
       fbbpp  values being used, or failing that, the first that has neither a
       depth or fbbpp value specified.  The Display subsections are  optional.
       When  there  isn't one that matches the depth and/or fbbpp values being
       used, all the parameters that can be specified here fall back to  their
       defaults.

       Display subsections have the following format:

               SubSection "Display"
                   Depth  depth
                   entries
                   ...
               EndSubSection

       Depth  depth
              This entry specifies what colour depth the Display subsection is
              to be used for.  This entry is usually specified, but it may  be
              omitted to create a match-all Display subsection or when wishing
              to match only against the FbBpp parameter.  The range  of  depth
              values  that  are  allowed  depends on the driver.  Most drivers
              support 8, 15, 16 and 24.  Some also support  1  and/or  4,  and
              some  may support other values (like 30).  Note: depth means the
              number of bits in a pixel that are actually  used  to  determine
              the pixel colour.  32 is not a valid depth value.  Most hardware
              that uses 32 bits per pixel only uses 24 of  them  to  hold  the
              colour information, which means that the colour depth is 24, not
              32.

       FbBpp  bpp
              This entry specifies the framebuffer format this Display subsec-
              tion  is to be used for.  This entry is only needed when provid-
              ing depth 24 configurations that allow a choice between a 24 bpp
              packed framebuffer format and a 32bpp sparse framebuffer format.
              In most cases this entry should not be used.

       Weight  red-weight green-weight blue-weight
              This optional entry specifies the relative RGB weighting  to  be
              used  for  a  screen  is being used at depth 16 for drivers that
              allow multiple formats.  This may also  be  specified  from  the
              command line with the -weight option (see Xorg(1)).

       Virtual  xdim ydim
              This  optional  entry specifies the virtual screen resolution to
              be used.  xdim must be a multiple of either 8  or  16  for  most
              drivers,  and  a multiple of 32 when running in monochrome mode.
              The given value will be rounded down if this is  not  the  case.
              Video  modes  which are too large for the specified virtual size
              will be rejected.  If this entry is  not  present,  the  virtual
              screen resolution will be set to accommodate all the valid video
              modes given in the Modes entry.  Some drivers/hardware  combina-
              tions  do not support virtual screens.  Refer to the appropriate
              driver-specific documentation for details.

       ViewPort  x0 y0
              This optional entry sets the upper left corner  of  the  initial
              display.   This is only relevant when the virtual screen resolu-
              tion is different from the resolution of the initial video mode.
              If  this  entry  is  not given, then the initial display will be
              centered in the virtual display area.

       Modes  "mode-name" ...
              This optional entry specifies the list of video  modes  to  use.
              Each  mode-name  specified  must be in double quotes.  They must
              correspond to those specified or referenced in  the  appropriate
              Monitor  section  (including implicitly referenced built-in VESA
              standard modes).  The server will delete modes  from  this  list
              which  don't satisfy various requirements.  The first valid mode
              in this list will be the default display mode for startup.   The
              list  of  valid  modes  is  converted internally into a circular
              list.   It  is  possible  to  switch  to  the  next  mode   with
              Ctrl+Alt+Keypad-Plus and to the previous mode with Ctrl+Alt+Key-
              pad-Minus.  When this entry is omitted, the valid  modes  refer-
              enced  by  the appropriate Monitor section will be used.  If the
              Monitor section contains no modes, then the  selection  will  be
              taken from the built-in VESA standard modes.

       Visual  "visual-name"
              This optional entry sets the default root visual type.  This may
              also be specified from the command line (see the Xserver(1)  man
              page).   The  visual types available for depth 8 are (default is
              PseudoColor):

                  StaticGray
                  GrayScale
                  StaticColor
                  PseudoColor
                  TrueColor
                  DirectColor

              The visual type available for the  depths  15,  16  and  24  are
              (default is TrueColor):

                  TrueColor
                  DirectColor

              Not all drivers support DirectColor at these depths.

              The visual types available for the depth 4 are (default is Stat-
              icColor):

                  StaticGray
                  GrayScale
                  StaticColor
                  PseudoColor

              The visual type available for the depth 1 (monochrome) is  Stat-
              icGray.

       Black  red green blue
              This  optional  entry allows the "black" colour to be specified.
              This is only supported at depth 1.  The default is black.

       White  red green blue
              This optional entry allows the "white" colour to  be  specified.
              This is only supported at depth 1.  The default is white.

       Options
              Option flags may be specified in the Display subsections.  These
              may  include  driver-specific  options  and   driver-independent
              options.   The former are described in the driver-specific docu-
              mentation.  Some of the latter are described above in  the  sec-
              tion  about  the  Screen  section, and they may also be included
              here.

SERVERLAYOUT SECTION
       The config file may have multiple  ServerLayout  sections.   A  "server
       layout" represents the binding of one or more screens (Screen sections)
       and one or more input devices (InputDevice sections) to form a complete
       configuration.   In  multi-head  configurations,  it also specifies the
       relative layout of the heads.  A  ServerLayout  section  is  considered
       "active"  if  it is referenced by the -layout command line option or by
       an Option "DefaultServerLayout" entry in the ServerFlags  section  (the
       former  takes  precedence  over  the latter).  If those options are not
       used, the first ServerLayout section found in the config file  is  con-
       sidered  the  active one.  If no ServerLayout sections are present, the
       single active screen and two active (core) input devices  are  selected
       as described in the relevant sections above.

       ServerLayout sections have the following format:

           Section "ServerLayout"
               Identifier   "name"
               Screen       "screen-id"
               ...
               InputDevice  "idev-id"
               ...
               options
               ...
           EndSection

       Each  ServerLayout  section  must have an Identifier entry and at least
       one Screen entry.

       The Identifier entry specifies the unique name for this server  layout.
       The  ServerLayout  section  provides  information specific to the whole
       session, including session-specific Options.  The  ServerFlags  options
       (described  above)  may be specified here, and ones given here override
       those given in the ServerFlags section.

       The entries that may be used in this section are described here.

       Screen  screen-num "screen-id" position-information
              One of these entries must be given for each screen being used in
              a  session.  The screen-id field is mandatory, and specifies the
              Screen  section  being  referenced.   The  screen-num  field  is
              optional,  and  may  be  used  to  specify  the screen number in
              multi-head configurations.  When  this  field  is  omitted,  the
              screens  will  be numbered in the order that they are listed in.
              The numbering starts from 0, and must be consecutive.  The posi-
              tion-information  field  describes  the way multiple screens are
              positioned.  There are a number  of  different  ways  that  this
              information can be provided:

              x y

              Absolute  x y
                  These  both specify that the upper left corner's coordinates
                  are (x,y).  The Absolute keyword is  optional.   Some  older
                  versions  of  XFree86  (4.2 and earlier) don't recognise the
                  Absolute keyword, so it's safest to just specify the coordi-
                  nates without it.

              RightOf   "screen-id"

              LeftOf    "screen-id"

              Above     "screen-id"

              Below     "screen-id"

              Relative  "screen-id" x y
                  These give the screen's location relative to another screen.
                  The first four position the screen immediately to the right,
                  left,  above or below the other screen.  When positioning to
                  the right or left, the top edges are  aligned.   When  posi-
                  tioning  above  or  below,  the left edges are aligned.  The
                  Relative form specifies the offset of  the  screen's  origin
                  (upper  left  corner)  relative  to  the  origin  of another
                  screen.

       InputDevice  "idev-id" "option" ...
              One of these entries should be given for each input device being
              used in a session.  Normally at least two are required, one each
              for the core pointer and keyboard devices.  If either  of  those
              is  missing, suitable InputDevice entries are searched for using
              the method described above  in  the  INPUTDEVICE  section.   The
              idev-id field is mandatory, and specifies the name of the Input-
              Device section being referenced.  Multiple option fields may  be
              specified,  each  in  double quotes.  The options permitted here
              are any that may also be  given  in  the  InputDevice  sections.
              Normally  only  session-specific  input  device options would be
              used here.  The most commonly used options are:

                  "CorePointer"
                  "CoreKeyboard"
                  "SendCoreEvents"

              and the first two should normally be used to indicate  the  core
              pointer and core keyboard devices respectively.

       MatchSeat  seat-id
              Only  apply  this  ServerLayout  section if X server was started
              with -seat seat-id option.

       Options
              In addition to  the  following,  any  option  permitted  in  the
              ServerFlags  section  may also be specified here.  When the same
              option appears in both places, the value  given  here  overrides
              the one given in the ServerFlags section.

       Option "IsolateDevice"  "bus-id"
              Restrict  device  resets to the specified bus-id.  See the BusID
              option (described in DEVICE SECTION, above) for  the  format  of
              the  bus-id  parameter.   This  option  overrides SingleCard, if
              specified.  At present, only PCI devices can be isolated in this
              manner.

       Option "SingleCard"  "boolean"
              As  IsolateDevice, except that the bus ID of the first device in
              the layout is used.

       Here is an example of a ServerLayout section for a dual headed configu-
       ration with two mice:

           Section "ServerLayout"
               Identifier  "Layout 1"
               Screen      "MGA 1"
               Screen      "MGA 2" RightOf "MGA 1"
               InputDevice "Keyboard 1" "CoreKeyboard"
               InputDevice "Mouse 1"    "CorePointer"
               InputDevice "Mouse 2"    "SendCoreEvents"
               Option      "BlankTime"  "5"
           EndSection

DRI SECTION
       This  optional  section  is  used  to  provide some information for the
       Direct Rendering Infrastructure.  Details about the format of this sec-
       tion can be found on-line at <http://dri.freedesktop.org/>.

VENDOR SECTION
       The optional Vendor section may be used to provide vendor-specific con-
       figuration information.  Multiple Vendor sections may be  present,  and
       they  may  contain  an Identifier entry and multiple Option flags.  The
       data therein is not used in this release.

ATTRIBUTES
       See attributes(7) for descriptions of the following attributes:


       +---------------+------------------+
       |ATTRIBUTE TYPE | ATTRIBUTE VALUE  |
       +---------------+------------------+
       |Availability   | x11/server/xorg  |
       +---------------+------------------+
       |Stability      | Volatile         |
       +---------------+------------------+
SEE ALSO
       General: X(7), Xserver(1), Xorg(1), cvt(1), gtf(1).

       Not all modules or interfaces are available on all platforms.

       Display  drivers:  apm(4),  ati(4),  chips(4),   cirrus(4),   cyrix(4),
       fbdev(4),  glide(4),  glint(4),  i128(4),  i740(4), imstt(4), intel(4),
       mga(4), neomagic(4), nv(4), openchrome(4), r128(4),  radeon(4),  rendi-
       tion(4),  savage(4),  s3virge(4),  siliconmotion(4), sis(4), sisusb(4),
       sunbw2(4),  suncg14(4),  suncg3(4),  suncg6(4),  sunffb(4),  sunleo(4),
       suntcx(4),   tdfx(4),   trident(4),   tseng(4),   vesa(4),   vmware(4),
       voodoo(4), wsfb(4), xgi(4), xgixp(4).

       Input drivers: acecad(4), citron(4), elographics(4), evdev(4), fpit(4),
       joystick(4), kbd(4), libinput(4), mousedrv(4), mutouch(4), penmount(4),
       synaptics(4), vmmouse(4), void(4), wacom(4).

       Other modules and interfaces: exa(4), fbdevhw(4), v4l(4).

AUTHORS
       This   manual   page   was   largely   rewritten   by    David    Dawes
       <dawes@xfree86.org>.



NOTES
       This     software     was    built    from    source    available    at
       https://github.com/oracle/solaris-userland.   The  original   community
       source   was   downloaded   from    https://www.x.org/releases/individ-
       ual/xserver/xorg-server-1.20.3.tar.bz2

       Further information about this software can be found on the open source
       community website at https://www.x.org.



X Version 11                  xorg-server 1.20.3                  xorg.conf(5)