ZS7-2 Front and Rear Panel Components

Language:

ZS7-2 Front Panel Components - The ZS7-2 controller drive slots and front panel components are shown in the following figure.

Figure 1 ZS7-2 Front Panel

image:The image shows the ZS7-2 front panel components.

1 RFID tag	2 System status LED: Locator (white)	3 System status LED: Service Action Required (amber)
4 System status LED: Power/OK (green)	5 Power button	6 Fan service action required (amber)
7 Power Supply (PS) service action required (amber)	8 Over-temperature warning (amber)	9 Service Processor (SP) OK (green)
10 Do Not Service indicator	11 System disk 0	12 System disk 1
13 Filler panel	14 Filler panel	15 Filler panel
16 Filler panel	17 Filler panel	18 Filler panel
19 Filler panel	20 Filler panel	21 Filler panel
22 Filler panel

ZS7-2 Rear Panel Components - The ZS7-2 controller PCIe slots and rear panel components are shown in the following figure.

Figure 2 ZS7-2 Rear Panel

image:The image shows the ZS7-2 high-end model rear panel components.

1 Power Supply (PS) Unit 1 (PS 1)	2 PS 1 status indicators (top to bottom): Attention (amber) Power/OK (green)	3 PS 0
4 PS 0 status indicators (top to bottom): Attention (amber) Power/OK (green)	5 Fifth PCIe option (slot 1)	6 External SAS-3 HBA (slot 2)
7 Slot 3: High-end model: External SAS-3 HBA Mid-range model: Filler panel	8 First PCIe option (slot 4)	9 Third PCIe option (slot 5)
10 Cluster interface card (slot 6)	11 Serial management (SER MGT) RJ-45 serial port	12 Service Processor (SP) NET MGT port
13 Network (NET) 100/1000BASE-T RJ-45 Gigabit Ethernet (GbE) port: NET 0	14 USB 3.0 port	15 System status LEDs: Locate (white) - left Attention (amber) - right, top Power/OK (green) - right, bottom
16 Fourth PCIe option (slot 7)	17 Second PCIe option (slot 8)	18 Slot 9: High-end model: External SAS-3 HBA Mid-range model: Filler panel
19 External SAS-3 HBA (slot 10)	20 Internal SAS-3 HBA (slot 11)

Cluster Interface Card Compatibility - The ZS7-2 controller contains a Version 3 cluster interface card, which is incompatible with Version 2.

For information about how to connect cables to form a cluster, see Connecting Cluster Cables in Oracle ZFS Storage Appliance Cabling Guide.

Ethernet Port

The ZS7-2 has one RJ-45 100/1000BASE-T Gigabit Ethernet (GbE) network connector, labeled NET0, on the rear panel. The port operates at 100 Mbits/sec or1000 Mbits/sec. Use this port to connect the appliance to the network.

There are two status indicators (LEDs) on this port. These indicators are visible from the rear of the controller.

Table 15 Gigabit Ethernet Port Status Indicators

Status Indicator Name	Location	Color	State and Meaning
Activity	Bottom left	Green	ON – Link up OFF – No link FLASHING – Packet activity
Link speed	Bottom right	Green	OFF – 100BASE-T link (if link up) ON – 1000BASE-T link

Network Management Port

The ZS7-2 controller has one 10/100/1000BASE-T Ethernet management domain interface, labeled NET MGT. There are two status indicators (LEDs) on this port. These indicators are visible from the rear of the controller. The service processor NET MGT port is the optional connection to the Oracle ILOM service processor. The NET MGT port is configured by default to use Dynamic Host Configuration Protocol (DHCP). The service processor NET MGT port uses an RJ-45 cable for a 10/100/1000BASE-T connection.

Table 16 Network Management Port Status Indicators

Status Indicator Name	Location	Color	State and Meaning
Activity	Top left	Green	ON – Link up OFF – No link FLASHING – Packet activity
Link speed	Top right	Green	ON – 1000BASE-T link OFF – 10/100BASE-T link

Serial Management Port

The service processor SER MGT port uses an RJ-45 cable and is the default connection to the Oracle ILOM service processor. This port supports local connections to the controller and only recognizes Oracle ILOM command-line interface (CLI) commands. Typically you connect a terminal or terminal emulator to this port.

Note - This port does not support network connections.

4x4 SAS HBA Ports

The 4x4 SAS HBAs are installed in PCIe slots 2, 3, 9, and 10 for the ZS7-2 high-end model, and slots 2 and 10 for the ZS7-2 mid-range model. The HBAs provide connectivity to external disk shelves. The HBA logical ports are numbered 0-3, bottom to top, as shown in the following figure.

Figure 3 ZS7-2 4x4 SAS HBA