Oracle^® ZFS Storage Appliance Customer Service Manual

ZS5-4 Front and Rear Panel Components

ZS5-4 Front Panel Components - The ZS5-4 controller drive slots and front panel components are shown in the following figure.

Figure 1  ZS5-4 Front Panel

1 LEDs (left to right) Locator Service action required Power/OK 2 Power button 3 Alert indicators (left to right) Service Processor (SP) OK/Fault Fan/ CPU/ Memory service action required Power Supply (PS) service action required Over-temperature warning 4 Permanent HDD filler panels 5 System disk 1 6 System disk 0 7 DVD filler panel 8 DB-15 VGA port 9 Two USB 2.0 ports 10 RFID tag

ZS5-4 Rear Panel Components - The ZS5-4 controller PCIe slots and rear panel components are shown in the following figure.

Figure 2  ZS5-4 Rear Panel

1 Power Supply Unit (PSU) 0 2 PSU 1 3 DB-15 VGA port 4 SER MGT port 5 Service Processor (SP) NET MGT port 6 First PCle (slot 11) 7 Fifth PCIe (slot 10) 8 Third 4x4 SAS HBA or seventh PCIe (slot 9) 9 Second PCIe (slot 8) 10 4X4 SAS HBA (slot 7) 11 Two USB 2.0 ports 12 Network (NET) 10 Gb Ethernet ports, NET 0 - NET 3 13 4X4 SAS HBA (slot 6) 14 Third PCIe (slot 5) 15 Cluster interface card (slot 4) 16 Fourth 4X4 SAS HBA or sixth PCIe (slot 3) 17 Internal SAS HBA (slot 2) 18 Fourth PCIe (slot 1) 19 System status LEDs (left to right) Power/OK (green) Attention (amber) Locate (white) 20 PSU 1 AC inlet 21 PSU 0 AC inlet

Cluster Interface Card Compatibility - The ZS5-4 controller contains a Version 3 cluster interface card, which is incompatible with Version 2.

For information about how to connect cables to form a cluster, see Connecting Cluster Cables in Oracle ZFS Storage Appliance Cabling Guide.

Ethernet Ports

The ZS5-4 has four RJ-45 10-Gigabit Ethernet (10GbE) network connectors, labeled NET0, NET1, NET2, NET3 in a quadrant (where NET0 and NET1 are bottom left to right, NET2 is above NET0 and NET3 is above NET1) on the rear panel. The ports operate at 100 Mbits/sec, 1000 Mbit/sec, or 10-Gbits/sec. Use these ports to connect the appliance to the network.

There are two status indicators (LEDs) on each port. These indicators are visible from the rear of the controller.

Table 15  Gigabit Ethernet Port Status Indicators

Status Indicator Name Location Color State and Meaning Activity Top left Green ON – No link OFF– No activity FLASHING – Packet activity Link speed Top right Bicolored: Amber/Green OFF – 100BASE-T link Amber ON – 1000BASE-T link Green ON – 10GBASE-T link

Network Management Port

The ZS5-4 controller has one 10/100/1000BASE-T Ethernet management domain interface, labeled NET MGT. There are two status indicators (LEDs) on this port. These indicators are visible from the rear of the controller. The service processor NET MGT port is the optional connection to the Oracle ILOM service processor. The NET MGT port is configured by default to use Dynamic Host Configuration Protocol (DHCP). The service processor NET MGT port uses an RJ-45 cable for a 10/100/1000BASE-T connection.

Table 16  Network Management Port Status Indicators

Status Indicator Name Location Color State and Meaning Activity Top left Amber ON – Link up OFF – No link or down link FLASHING – Packet activity Link speed Top right Green Green ON – 1000BASE-T link OFF – 10/100BASE-T link

Serial Management Port

The service processor SER MGT port uses an RJ-45 cable and is the default connection to the Oracle ILOM service processor. This port supports local connections to the server and only recognizes Oracle ILOM command-line interface (CLI) commands. Typically you connect a terminal or terminal emulator to this port.

4x4 SAS HBA Ports

The 4x4 SAS HBA, installed in PCle slot 6 or slot 7 of the ZS5-4, provides connectivity to external disk shelves. The HBA logical ports are numbered 3-0, top to bottom, as shown in the following figure.

Figure 3  ZS5-4 4x4 SAS HBA