Gestion des périphériques dans Oracle® Solaris 11.2

Quitter la vue de l'impression

Mis à jour : Juillet 2014
 
 

Modification des partitions et création d'un système de fichiers PCFS sur un périphérique de stockage USB

Les étapes suivantes décrivent comment supprimer une partition existante, créer une partition, puis créer un système de fichiers PCFS sur le périphérique USB. Assurez-vous de sauvegarder toutes les données avant d'effectuer cette tâche.

  1. Connectez-vous en tant qu'administrateur.
  2. Modifier les partitions tel que suit :
    1. Démarrez l'utilitaire fdisk.
      # fdisk device
    2. Sur le programme d'installation en mode interface affichée, choisissez les options appropriées pour les actions suivantes lorsque vous y êtes invité.
      • Supprimez la partition.

      • Spécifiez le numéro de la partition à supprimer.

      • Créer la partition.

      • Sélectionnez le type de partition à créer.

      • Indiquez le pourcentage de l'espace disque à utiliser pour cette partition.

      • Indiquer si la nouvelle partition doit être actifs ou inactifs.

      • Choisissez de mettre à jour la configuration du disque et quittez.

  3. Démontez le périphérique, si nécessaire.

    Pour plus d'informations sur le démontage d'un périphérique USB, reportez-vous à la section Montage ou démontage d'un périphérique de stockage USB.

  4. Créez le système de fichiers PCFS sur cette partition.
    # mkfs -F FS-type -o FS-type-specific-option raw-device-file
    
Exemple 13-1  La modification de disquettes USB les partitions d'un

Dans l'exemple suivant, la configuration de disque de c3t0d0p0 est modifiée, en commençant par la création d'une nouvelle partition.

# fdisk /dev/rdsk/c3t0d0p0
      Total disk size is 29 cylinders
Cylinder size is 2048 (512 byte) blocks

Cylinders
Partition   Status    Type          Start   End   Length    %
=========   ======    ============  =====   ===   ======   ===
1       Active    Solaris2          1    28      28     97

SELECT ONE OF THE FOLLOWING:
1. Create a partition
2. Specify the active partition
3. Delete a partition
4. Change between Solaris and Solaris2 Partition IDs
5. Exit (update disk configuration and exit)
6. Cancel (exit without updating disk configuration)
Enter Selection: 3Partition will be deleted.


      Total disk size is 29 cylinders
Cylinder size is 2048 (512 byte) blocks

Cylinders
Partition   Status    Type          Start   End   Length    %
=========   ======    ============  =====   ===   ======   ===
1       Active    Solaris2          1    28      28     97

SELECT ONE OF THE FOLLOWING:
1. Create a partition
2. Specify the active partition
3. Delete a partition
4. Change between Solaris and Solaris2 Partition IDs
5. Exit (update disk configuration and exit)
6. Cancel (exit without updating disk configuration)
Specify the partition number to delete (or enter 0 to exit): 1Partition number to delete.

Partition deleted.Deletion is completed.


      Total disk size is 29 cylinders
Cylinder size is 2048 (512 byte) blocks

Cylinders
Partition   Status    Type          Start   End   Length    %
=========   ======    ============  =====   ===   ======   ===

WARNING: no partitions are defined!

SELECT ONE OF THE FOLLOWING:
1. Create a partition
2. Specify the active partition
3. Delete a partition
4. Change between Solaris and Solaris2 Partition IDs
5. Exit (update disk configuration and exit)
6. Cancel (exit without updating disk configuration)
Enter Selection: 1Partition will be created.


      Total disk size is 29 cylinders
Cylinder size is 2048 (512 byte) blocks

Cylinders
Partition   Status    Type          Start   End   Length    %
=========   ======    ============  =====   ===   ======   ===

WARNING: no partitions are defined!

SELECT ONE OF THE FOLLOWING:
1. Create a partition
2. Specify the active partition
3. Delete a partition
4. Change between Solaris and Solaris2 Partition IDs
5. Exit (update disk configuration and exit)
6. Cancel (exit without updating disk configuration)
Select the partition type to create:
1=SOLARIS2  2=UNIX        3=PCIXOS     4=Other
5=DOS12     6=DOS16       7=DOSEXT     8=DOSBIG
9=DOS16LBA  A=x86 Boot    B=Diagnostic C=FAT32
D=FAT32LBA  E=DOSEXTLBA   F=EFI        0=Exit? cPartition type is selected.


       Total disk size is 29 cylinders
Cylinder size is 2048 (512 byte) blocks

Cylinders
Partition   Status    Type          Start   End   Length    %
=========   ======    ============  =====   ===   ======   ===

WARNING: no partitions are defined!

SELECT ONE OF THE FOLLOWING:
1. Create a partition
2. Specify the active partition
3. Delete a partition
4. Change between Solaris and Solaris2 Partition IDs
5. Exit (update disk configuration and exit)
6. Cancel (exit without updating disk configuration)
Select the partition type to create:
Specify the percentage of disk to use for this partition (or type "c" to
specify the size in cylinders). 100Percentage of disk space is specified.


              Total disk size is 29 cylinders
Cylinder size is 2048 (512 byte) blocks

Cylinders
Partition   Status    Type          Start   End   Length    %
=========   ======    ============  =====   ===   ======   ===

WARNING: no partitions are defined!

SELECT ONE OF THE FOLLOWING:
1. Create a partition
2. Specify the active partition
3. Delete a partition
4. Change between Solaris and Solaris2 Partition IDs
5. Exit (update disk configuration and exit)
6. Cancel (exit without updating disk configuration)
Select the partition type to create:
Should this become the active partition? If yes, it  will be activated
each time the computer is reset or turned on.
Please type "y" or "n". nInactive partition is selected.


      Total disk size is 29 cylinders
Cylinder size is 2048 (512 byte) blocks

Cylinders
Partition   Status    Type          Start   End   Length    %
=========   ======    ============  =====   ===   ======   ===
1                 Win95 FAT32       1    28      28     97

SELECT ONE OF THE FOLLOWING:
1. Create a partition
2. Specify the active partition
3. Delete a partition
4. Change between Solaris and Solaris2 Partition IDs
5. Exit (update disk configuration and exit)
6. Cancel (exit without updating disk configuration)
Enter Selection: 5Disk configuration will be updated.

# mkfs -F pcfs -o fat=32 /dev/rdsk/c3t0d0p0:c
Construct a new FAT file system on /dev/rdsk/c3t0d0p0:c: (y/n)? yFile system is created.