smp_rep_general - invoke REPORT GENERAL SMP function
smp_rep_general [--brief] [--changecount] [--help] [--hex] [--inter- face=PARAMS] [--raw] [--sa=SAS_ADDR] [--verbose] [--version] [--zero] SMP_DEVICE[,N]
SMP_REP_GENERAL(8) SMP_UTILS SMP_REP_GENERAL(8) NAME smp_rep_general - invoke REPORT GENERAL SMP function SYNOPSIS smp_rep_general [--brief] [--changecount] [--help] [--hex] [--inter- face=PARAMS] [--raw] [--sa=SAS_ADDR] [--verbose] [--version] [--zero] SMP_DEVICE[,N] DESCRIPTION Sends a SAS Serial Management Protocol (SMP) REPORT GENERAL function request to an SMP target. The SMP target is identified by the SMP_DEVICE and the SAS_ADDR. Depending on the interface, the SAS_ADDR may be deduced from the SMP_DEVICE. The mpt interface uses SMP_DEVICE to identify a HBA (an SMP initiator) and needs the additional ,N to differentiate between HBAs if there are multiple present. OPTIONS Mandatory arguments to long options are mandatory for short options as well. -b, --brief reports (prints to stdout) only a few important fields from the response. -c, --changecount reports (prints to stdout) the value of the expander change count field from the response. The value is printed in decimal and is in the range 0 to 65535. Only expanders compliant with SAS-1.1 (and earlier) should yield 0. [Expanders compliant with SAS-2 (and later) should set the "long response" bit in the REPORT GENERAL response to 1.] -h, --help output the usage message then exit. -H, --hex output the response (less the CRC field) in hexadecimal. -I, --interface=PARAMS interface specific parameters. In this case "interface" refers to the path through the operating system to the SMP initiator. See the smp_utils man page for more information. -r, --raw send the response (less the CRC field) to stdout in binary. All error messages are sent to stderr. -s, --sa=SAS_ADDR specifies the SAS address of the SMP target device. Typically this is an expander. This option may not be needed if the SMP_DEVICE has the target's SAS address within it. The SAS_ADDR is in decimal but most SAS addresses are shown in hexadecimal. To give a number in hexadecimal either prefix it with '0x' or put a trailing 'h' on it. -v, --verbose increase the verbosity of the output. Can be used multiple times -V, --version print the version string and then exit. -z, --zero zero the Allocated Response Length field in the request. This is required for strict SAS-1.1 compliance. However this option should not be given in SAS-2 and later; if it is given an abridged response may result. EXAMPLES See "Examples" section in http://sg.danny.cz/sg/smp_utils.html CONFORMING TO The SMP REPORT GENERAL function was introduced in SAS-1, with small additions in SAS-1.1 . There have been a large number of additions in SAS-2 . AUTHORS Written by Douglas Gilbert. REPORTING BUGS Report bugs to <dgilbert at interlog dot com>. COPYRIGHT Copyright (C) 2006-2011 Douglas Gilbert This software is distributed under a FreeBSD license. There is NO war- ranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR- POSE. ATTRIBUTES See attributes(7) for descriptions of the following attributes: +---------------+--------------------------+ |ATTRIBUTE TYPE | ATTRIBUTE VALUE | +---------------+--------------------------+ |Availability | system/storage/smp_utils | +---------------+--------------------------+ |Stability | Uncommitted | +---------------+--------------------------+ SEE ALSO smp_utils, smp_discover(smp_utils) NOTES Source code for open source software components in Oracle Solaris can be found at https://www.oracle.com/downloads/opensource/solaris-source- code-downloads.html. This software was built from source available at https://github.com/oracle/solaris-userland. The original community source was downloaded from http://sg.danny.cz/sg/p/smp_utils-0.98.tgz. Further information about this software can be found on the open source community website at http://sg.danny.cz/sg/smp_utils.html. smp_utils-0.96 May 2011 SMP_REP_GENERAL(8)